Electrolux Washing Machines Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E10
Washer will not fill or takes a very long time to fill; E10 displayed shortly after cycle start.
Water Inlet Timeout / Fill Fault
E11
Washer does not fill to the correct level; E11 displayed; cycle may pause or abort.
Fill Level Not Reached / Water Level Sensor Fault
E13
Washer detects water in base pan or internal leak; E13 displayed; machine may stop and attempt to drain.
Water Leak Detected / Overflow Protection
E20
Washer will not drain or drains very slowly; E20 displayed; cycle may stop before spin.
Drain Pump / Drainage Fault
E21
Washer attempts to drain but times out; E21 displayed; water remains in drum.
Drain Timeout / Pump Performance Fault
E23
Washer will not drain; E23 displayed; pump does not run even though water is in drum.
Drain Pump Triac / Control Circuit Fault
E24
Washer shows E24 and may not drain; intermittent pump operation.
Drain Pump Feedback / Wiring Fault
E30
Washer stops mid-cycle and displays E30; may also show water in base pan.
Generic Water Leak / Overflow Fault
E31
Washer displays E31; irregular filling behavior or incorrect water levels.
Pressure Sensor Calibration / Signal Fault
E32
Washer shows E32; water level readings appear unstable (overfilling or underfilling).
Pressure Sensor Range / Out-of-Range Signal
E35
Washer overfills or shows E35; water level too high in drum; may trigger drain pump.
Overfill / Pressure Sensor High-Level Fault
E38
Washer displays E38; incorrect water level detection; may not spin or may drain unexpectedly.
Blocked Air Trap / Pressure Chamber Fault
E40
Washer will not start; E40 displayed; door appears closed but cycle will not begin.
Door Lock / Door Not Properly Closed
E41
Washer displays E41; control thinks door is open even when closed.
Door Open Signal Fault
E42
Washer shows E42; door remains locked or unlocks unexpectedly during cycle.
Door Locking/Unlocking Fault
E43
Washer displays E43; door lock circuit error; machine may not start.
Door Lock Triac / Control Board Fault
E44
Washer shows E44; door status sensing error.
Door Status Sensor Fault
E45
Washer displays E45; advanced door lock circuit fault.
Door Lock Communication / Triac Fault
E50
Washer will not spin or tumble; E50 displayed; may attempt to start then stop.
General Motor / Drive Fault
E51
Washer shows E51; motor does not run; may hum briefly.
Motor Power Triac Short Circuit
E52
Washer displays E52; drum may start to move then stop; erratic spin speeds.
Motor Tachometer Signal Fault
E53
Washer shows E53; motor control error; no spin or tumble.
Motor Control Triac / Driver Fault
E54
Washer displays E54; motor relay sticking or not engaging properly.
Motor Relay Fault
E55
Washer shows E55; motor power fault; no drum movement.
Motor Power Supply Fault
E56
Washer displays E56; high motor current detected; may stop mid-spin.
Motor Overcurrent Fault
E60
Washer-dryer combo or washer with heater shows E60; water not heating correctly.
General Heating System Fault
E61
Washer displays E61; water heating too slowly or not reaching target temperature.
Heating Performance Fault
E62
Washer shows E62; overheating detected; water gets excessively hot.
Overheating / Heater Stuck On
E66
Washer displays E66; heater relay fault; no heating or intermittent heating.
Heater Relay / Control Board Fault
E70
Washer shows E70; temperature sensor circuit error.
NTC Temperature Sensor Fault
E90
Washer displays E90; general communication error; may not start or respond correctly.
User Interface / Main Control Communication Fault
E91
Washer shows E91; no communication with user interface.
UI Communication Fault
E92
Washer displays E92; configuration or communication mismatch between boards.
Configuration / Communication Error
E93
Washer shows E93; configuration error detected.
Incorrect Configuration Data
E94
Washer displays E94; program configuration error; cycles may behave abnormally.
Program Configuration Fault
E95
Washer shows E95; communication error between microcontrollers on the main board.
Internal Control Board Communication Fault
E96
Washer displays E96; hardware configuration mismatch.
Hardware Configuration Fault
E97
Washer shows E97; program selector and configuration mismatch.
Program Selector / Configuration Fault
E98
Washer displays E98; communication error between main control and motor control section.
Motor Control Communication Fault
Symptom
Washer displays incorrect water temperature (cold when set to hot, or vice versa).
Water Supply / Valve Misconnection
Symptom
Washer door will not unlock at end of cycle; clothes are trapped inside.
Door Lock Stuck / No Unlock
Symptom
Washer drum does not turn at all during wash or spin, but the machine fills and drains normally.
No Drum Movement / Drive Failure
Symptom
Washer emits a burning smell or electrical odor during operation.
Overheating Component / Electrical Fault
Symptom
Washer fills and agitates but will not spin; clothes remain very wet at end of cycle.
No Spin / Spin Inhibit Condition
Symptom
Washer has a strong musty or moldy odor, especially from the drum or door gasket.
Biofilm / Mold Build-Up
Symptom
Washer is very noisy during spin; loud rumbling, grinding, or roaring sound from drum area.
Drum Bearing Failure
Symptom
Washer leaks water from the front door area during wash or spin.
Door Boot / Gasket Leak
Symptom
Washer leaks water from underneath or at the rear during operation.
Internal Hose or Pump Leak
Symptom
Washer leaves clothes with detergent residue or white streaks after washing.
Poor Rinsing / Detergent Residue
Symptom
Washer makes loud banging or knocking noises during spin; machine may move or "walk" across the floor.
Excessive Vibration / Suspension Fault
Symptom
Washer powers on but will not start any cycle; Start button unresponsive or cycle cancels immediately.
Start Circuit / User Interface Fault
Symptom
Washer produces a high-pitched squealing or chirping noise during spin.
Belt Slippage / Pulley Noise
Symptom
Washer takes much longer than expected to complete cycles; time remaining jumps up or down.
Extended Cycle Time / Adaptive Control Response
Symptom
Washer will not power on at all; no lights or display, even with outlet known to be live.
No Power / Dead Appliance
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E10 |
Washer will not fill or takes a very long time to fill; E10 displayed shortly after cycle start.
|
Water Inlet Timeout / Fill Fault | View Details |
| E11 |
Washer does not fill to the correct level; E11 displayed; cycle may pause or abort.
|
Fill Level Not Reached / Water Level Sensor Fault | View Details |
| E13 |
Washer detects water in base pan or internal leak; E13 displayed; machine may stop and attempt to drain.
|
Water Leak Detected / Overflow Protection | View Details |
| E20 |
Washer will not drain or drains very slowly; E20 displayed; cycle may stop before spin.
|
Drain Pump / Drainage Fault | View Details |
| E21 |
Washer attempts to drain but times out; E21 displayed; water remains in drum.
|
Drain Timeout / Pump Performance Fault | View Details |
| E23 |
Washer will not drain; E23 displayed; pump does not run even though water is in drum.
|
Drain Pump Triac / Control Circuit Fault | View Details |
| E24 |
Washer shows E24 and may not drain; intermittent pump operation.
|
Drain Pump Feedback / Wiring Fault | View Details |
| E30 |
Washer stops mid-cycle and displays E30; may also show water in base pan.
|
Generic Water Leak / Overflow Fault | View Details |
| E31 |
Washer displays E31; irregular filling behavior or incorrect water levels.
|
Pressure Sensor Calibration / Signal Fault | View Details |
| E32 |
Washer shows E32; water level readings appear unstable (overfilling or underfilling).
|
Pressure Sensor Range / Out-of-Range Signal | View Details |
| E35 |
Washer overfills or shows E35; water level too high in drum; may trigger drain pump.
|
Overfill / Pressure Sensor High-Level Fault | View Details |
| E38 |
Washer displays E38; incorrect water level detection; may not spin or may drain unexpectedly.
|
Blocked Air Trap / Pressure Chamber Fault | View Details |
| E40 |
Washer will not start; E40 displayed; door appears closed but cycle will not begin.
|
Door Lock / Door Not Properly Closed | View Details |
| E41 |
Washer displays E41; control thinks door is open even when closed.
|
Door Open Signal Fault | View Details |
| E42 |
Washer shows E42; door remains locked or unlocks unexpectedly during cycle.
|
Door Locking/Unlocking Fault | View Details |
| E43 |
Washer displays E43; door lock circuit error; machine may not start.
|
Door Lock Triac / Control Board Fault | View Details |
| E44 |
Washer shows E44; door status sensing error.
|
Door Status Sensor Fault | View Details |
| E45 |
Washer displays E45; advanced door lock circuit fault.
|
Door Lock Communication / Triac Fault | View Details |
| E50 |
Washer will not spin or tumble; E50 displayed; may attempt to start then stop.
|
General Motor / Drive Fault | View Details |
| E51 |
Washer shows E51; motor does not run; may hum briefly.
|
Motor Power Triac Short Circuit | View Details |
| E52 |
Washer displays E52; drum may start to move then stop; erratic spin speeds.
|
Motor Tachometer Signal Fault | View Details |
| E53 |
Washer shows E53; motor control error; no spin or tumble.
|
Motor Control Triac / Driver Fault | View Details |
| E54 |
Washer displays E54; motor relay sticking or not engaging properly.
|
Motor Relay Fault | View Details |
| E55 |
Washer shows E55; motor power fault; no drum movement.
|
Motor Power Supply Fault | View Details |
| E56 |
Washer displays E56; high motor current detected; may stop mid-spin.
|
Motor Overcurrent Fault | View Details |
| E60 |
Washer-dryer combo or washer with heater shows E60; water not heating correctly.
|
General Heating System Fault | View Details |
| E61 |
Washer displays E61; water heating too slowly or not reaching target temperature.
|
Heating Performance Fault | View Details |
| E62 |
Washer shows E62; overheating detected; water gets excessively hot.
|
Overheating / Heater Stuck On | View Details |
| E66 |
Washer displays E66; heater relay fault; no heating or intermittent heating.
|
Heater Relay / Control Board Fault | View Details |
| E70 |
Washer shows E70; temperature sensor circuit error.
|
NTC Temperature Sensor Fault | View Details |
| E90 |
Washer displays E90; general communication error; may not start or respond correctly.
|
User Interface / Main Control Communication Fault | View Details |
| E91 |
Washer shows E91; no communication with user interface.
|
UI Communication Fault | View Details |
| E92 |
Washer displays E92; configuration or communication mismatch between boards.
|
Configuration / Communication Error | View Details |
| E93 |
Washer shows E93; configuration error detected.
|
Incorrect Configuration Data | View Details |
| E94 |
Washer displays E94; program configuration error; cycles may behave abnormally.
|
Program Configuration Fault | View Details |
| E95 |
Washer shows E95; communication error between microcontrollers on the main board.
|
Internal Control Board Communication Fault | View Details |
| E96 |
Washer displays E96; hardware configuration mismatch.
|
Hardware Configuration Fault | View Details |
| E97 |
Washer shows E97; program selector and configuration mismatch.
|
Program Selector / Configuration Fault | View Details |
| E98 |
Washer displays E98; communication error between main control and motor control section.
|
Motor Control Communication Fault | View Details |
| – |
Washer displays incorrect water temperature (cold when set to hot, or vice versa).
|
Water Supply / Valve Misconnection | View Details |
| – |
Washer door will not unlock at end of cycle; clothes are trapped inside.
|
Door Lock Stuck / No Unlock | View Details |
| – |
Washer drum does not turn at all during wash or spin, but the machine fills and drains normally.
|
No Drum Movement / Drive Failure | View Details |
| – |
Washer emits a burning smell or electrical odor during operation.
|
Overheating Component / Electrical Fault | View Details |
| – |
Washer fills and agitates but will not spin; clothes remain very wet at end of cycle.
|
No Spin / Spin Inhibit Condition | View Details |
| – |
Washer has a strong musty or moldy odor, especially from the drum or door gasket.
|
Biofilm / Mold Build-Up | View Details |
| – |
Washer is very noisy during spin; loud rumbling, grinding, or roaring sound from drum area.
|
Drum Bearing Failure | View Details |
| – |
Washer leaks water from the front door area during wash or spin.
|
Door Boot / Gasket Leak | View Details |
| – |
Washer leaks water from underneath or at the rear during operation.
|
Internal Hose or Pump Leak | View Details |
| – |
Washer leaves clothes with detergent residue or white streaks after washing.
|
Poor Rinsing / Detergent Residue | View Details |
| – |
Washer makes loud banging or knocking noises during spin; machine may move or "walk" across the floor.
|
Excessive Vibration / Suspension Fault | View Details |
| – |
Washer powers on but will not start any cycle; Start button unresponsive or cycle cancels immediately.
|
Start Circuit / User Interface Fault | View Details |
| – |
Washer produces a high-pitched squealing or chirping noise during spin.
|
Belt Slippage / Pulley Noise | View Details |
| – |
Washer takes much longer than expected to complete cycles; time remaining jumps up or down.
|
Extended Cycle Time / Adaptive Control Response | View Details |
| – |
Washer will not power on at all; no lights or display, even with outlet known to be live.
|
No Power / Dead Appliance | View Details |
No matching codes found
Advertisements