Haier Washing Machines Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E1
Washer stops and displays E1; tub does not fill with water or fills very slowly.
Water Inlet Timeout / No Fill
E10
Washer displays E10; communication error between main control board and display or inverter module.
Communication / PCB Interface Fault
E11
Washer displays E11; door cannot be unlocked at end of cycle or during error condition.
Door Unlock Failure
E12
Washer displays E12; abnormal water temperature detected (overheating or sensor out of range).
Overheat / Temperature Sensor Range Error
E13
Washer displays E13; water leakage detected in base tray or anti-flood system activated.
Leakage / Anti-Flood Protection
E14
Washer displays E14; water inlet valve or flow meter signal abnormal.
Inlet Flow Meter / Valve Control Fault
E2
Washer displays E2 and will not drain; water remains in the drum.
Drain Timeout / No Drain
E21
Washer displays E21; motor overload or stall detected during operation.
Motor Overload / Stall Protection
E22
Washer displays E22; abnormal current detected in motor circuit.
Motor Current / Inverter Error
E23
Washer displays E23; drain pump electrical fault detected.
Drain Pump Electrical Error
E24
Washer displays E24; door lock circuit electrical fault.
Door Lock Circuit Error
E25
Washer displays E25; EEPROM or memory error on control board.
Control Board Memory Fault
E3
Washer displays E3 and stops during spin; drum may be heavily loaded or unbalanced.
Unbalanced Load / Spin Protection
E4
Washer displays E4 and may not start or may stop mid-cycle; often related to door or lid not locking.
Door/Lid Lock Failure
E5
Washer displays E5; water temperature is abnormal or heating function fails.
Water Heating Fault / Temperature Sensor Error
E6
Washer displays E6; motor does not run or stops unexpectedly during wash or spin.
Motor Drive Fault
E7
Washer displays E7; water level reading is abnormal (overfill or no level change detected).
Water Level Sensor / Pressure Switch Fault
E8
Washer displays E8; often associated with water level too high or overflow condition.
Overflow / Overfill Protection
E9
Washer displays E9; drum speed feedback is abnormal or spin cannot be controlled.
Motor Tachometer / Speed Sensor Error
F1
Top-load Haier washer displays F1; lid switch or lid lock fault.
Lid Switch / Lid Lock Failure
F2
Top-load Haier washer displays F2; water level sensor or overflow issue.
Water Level / Overflow Fault (Top-Load)
F3
Top-load Haier washer displays F3; motor or drive fault.
Top-Load Motor / Drive Error
F4
Top-load Haier washer displays F4; drain fault similar to E2 on front-load models.
Top-Load Drain Timeout
F5
Top-load Haier washer displays F5; unbalanced load or spin fault.
Top-Load Unbalanced Spin
F6
Top-load Haier washer displays F6; water temperature sensor or heating fault (if equipped with heater).
Top-Load Temperature Sensor Fault
Symptom
Top-load washer agitator or pulsator does not move, but the motor can be heard running.
Agitator / Pulsator Drive Failure
Symptom
Washer displays incorrect water level (too little or too much) without showing a specific error code.
Water Level Calibration Issue
Symptom
Washer door or lid will not open at the end of the cycle, but no error code is shown.
Door Lock Stuck Closed
Symptom
Washer drum does not turn freely by hand; feels seized or very stiff.
Drum Seizure / Bearing or Foreign Object Jam
Symptom
Washer emits a burning smell during operation.
Overheating Component / Belt Slippage
Symptom
Washer fills with water but does not agitate or tumble; drum remains still during wash phase.
No Agitation / No Tumble
Symptom
Washer has a strong musty or moldy odor inside the drum or from the door seal.
Biofilm / Mold Build-Up
Symptom
Washer intermittently stops mid-cycle and then resumes or resets itself.
Intermittent Power / Control Fault
Symptom
Washer is very noisy during spin; loud rumbling, grinding, or roaring sound.
Drum Bearing Failure
Symptom
Washer leaks water from the front door area during wash or spin.
Door Gasket / Seal Leak
Symptom
Washer leaks water from underneath the machine.
Internal Hose / Pump Leak
Symptom
Washer leaves clothes covered in lint, residue, or undissolved detergent.
Poor Rinsing / Detergent Residue
Symptom
Washer makes a high-pitched squealing noise during spin.
Belt or Pulley Noise
Symptom
Washer makes loud banging or knocking noises during spin; machine may move or walk.
Excessive Vibration / Suspension Failure
Symptom
Washer powers on but will not start any cycle; Start button unresponsive or cycle will not initiate.
Start Circuit / User Interface Fault
Symptom
Washer takes much longer than expected to complete cycles.
Extended Cycle Time / Sensor Compensation
Symptom
Washer will not power on; no lights or display, machine appears completely dead.
No Power / Dead Control
Symptom
Washer will not spin or spins very slowly; clothes come out very wet.
No Spin / Weak Spin
Symptom
Washer's detergent drawer overflows or leaks water down the front of the machine.
Dispenser Overflow / Blockage
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E1 |
Washer stops and displays E1; tub does not fill with water or fills very slowly.
|
Water Inlet Timeout / No Fill | View Details |
| E10 |
Washer displays E10; communication error between main control board and display or inverter module.
|
Communication / PCB Interface Fault | View Details |
| E11 |
Washer displays E11; door cannot be unlocked at end of cycle or during error condition.
|
Door Unlock Failure | View Details |
| E12 |
Washer displays E12; abnormal water temperature detected (overheating or sensor out of range).
|
Overheat / Temperature Sensor Range Error | View Details |
| E13 |
Washer displays E13; water leakage detected in base tray or anti-flood system activated.
|
Leakage / Anti-Flood Protection | View Details |
| E14 |
Washer displays E14; water inlet valve or flow meter signal abnormal.
|
Inlet Flow Meter / Valve Control Fault | View Details |
| E2 |
Washer displays E2 and will not drain; water remains in the drum.
|
Drain Timeout / No Drain | View Details |
| E21 |
Washer displays E21; motor overload or stall detected during operation.
|
Motor Overload / Stall Protection | View Details |
| E22 |
Washer displays E22; abnormal current detected in motor circuit.
|
Motor Current / Inverter Error | View Details |
| E23 |
Washer displays E23; drain pump electrical fault detected.
|
Drain Pump Electrical Error | View Details |
| E24 |
Washer displays E24; door lock circuit electrical fault.
|
Door Lock Circuit Error | View Details |
| E25 |
Washer displays E25; EEPROM or memory error on control board.
|
Control Board Memory Fault | View Details |
| E3 |
Washer displays E3 and stops during spin; drum may be heavily loaded or unbalanced.
|
Unbalanced Load / Spin Protection | View Details |
| E4 |
Washer displays E4 and may not start or may stop mid-cycle; often related to door or lid not locking.
|
Door/Lid Lock Failure | View Details |
| E5 |
Washer displays E5; water temperature is abnormal or heating function fails.
|
Water Heating Fault / Temperature Sensor Error | View Details |
| E6 |
Washer displays E6; motor does not run or stops unexpectedly during wash or spin.
|
Motor Drive Fault | View Details |
| E7 |
Washer displays E7; water level reading is abnormal (overfill or no level change detected).
|
Water Level Sensor / Pressure Switch Fault | View Details |
| E8 |
Washer displays E8; often associated with water level too high or overflow condition.
|
Overflow / Overfill Protection | View Details |
| E9 |
Washer displays E9; drum speed feedback is abnormal or spin cannot be controlled.
|
Motor Tachometer / Speed Sensor Error | View Details |
| F1 |
Top-load Haier washer displays F1; lid switch or lid lock fault.
|
Lid Switch / Lid Lock Failure | View Details |
| F2 |
Top-load Haier washer displays F2; water level sensor or overflow issue.
|
Water Level / Overflow Fault (Top-Load) | View Details |
| F3 |
Top-load Haier washer displays F3; motor or drive fault.
|
Top-Load Motor / Drive Error | View Details |
| F4 |
Top-load Haier washer displays F4; drain fault similar to E2 on front-load models.
|
Top-Load Drain Timeout | View Details |
| F5 |
Top-load Haier washer displays F5; unbalanced load or spin fault.
|
Top-Load Unbalanced Spin | View Details |
| F6 |
Top-load Haier washer displays F6; water temperature sensor or heating fault (if equipped with heater).
|
Top-Load Temperature Sensor Fault | View Details |
| – |
Top-load washer agitator or pulsator does not move, but the motor can be heard running.
|
Agitator / Pulsator Drive Failure | View Details |
| – |
Washer displays incorrect water level (too little or too much) without showing a specific error code.
|
Water Level Calibration Issue | View Details |
| – |
Washer door or lid will not open at the end of the cycle, but no error code is shown.
|
Door Lock Stuck Closed | View Details |
| – |
Washer drum does not turn freely by hand; feels seized or very stiff.
|
Drum Seizure / Bearing or Foreign Object Jam | View Details |
| – |
Washer emits a burning smell during operation.
|
Overheating Component / Belt Slippage | View Details |
| – |
Washer fills with water but does not agitate or tumble; drum remains still during wash phase.
|
No Agitation / No Tumble | View Details |
| – |
Washer has a strong musty or moldy odor inside the drum or from the door seal.
|
Biofilm / Mold Build-Up | View Details |
| – |
Washer intermittently stops mid-cycle and then resumes or resets itself.
|
Intermittent Power / Control Fault | View Details |
| – |
Washer is very noisy during spin; loud rumbling, grinding, or roaring sound.
|
Drum Bearing Failure | View Details |
| – |
Washer leaks water from the front door area during wash or spin.
|
Door Gasket / Seal Leak | View Details |
| – |
Washer leaks water from underneath the machine.
|
Internal Hose / Pump Leak | View Details |
| – |
Washer leaves clothes covered in lint, residue, or undissolved detergent.
|
Poor Rinsing / Detergent Residue | View Details |
| – |
Washer makes a high-pitched squealing noise during spin.
|
Belt or Pulley Noise | View Details |
| – |
Washer makes loud banging or knocking noises during spin; machine may move or walk.
|
Excessive Vibration / Suspension Failure | View Details |
| – |
Washer powers on but will not start any cycle; Start button unresponsive or cycle will not initiate.
|
Start Circuit / User Interface Fault | View Details |
| – |
Washer takes much longer than expected to complete cycles.
|
Extended Cycle Time / Sensor Compensation | View Details |
| – |
Washer will not power on; no lights or display, machine appears completely dead.
|
No Power / Dead Control | View Details |
| – |
Washer will not spin or spins very slowly; clothes come out very wet.
|
No Spin / Weak Spin | View Details |
| – |
Washer's detergent drawer overflows or leaks water down the front of the machine.
|
Dispenser Overflow / Blockage | View Details |
No matching codes found
Advertisements