Midea Washing Machines Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E1
Washer stops mid-cycle and displays E1; water does not drain or drains very slowly.
Drainage Failure
E10
Washer displays E10; no water enters or fill is extremely slow at the beginning of the cycle.
Water Inlet Failure
E11
Washer shows E11; water does not drain within the expected time, often after rinse.
Drain Timeout
E12
Washer displays E12; heating function fails or water does not reach target temperature.
Heater Circuit Fault
E2
Washer displays E2 and will not spin; clothes remain very wet at the end of the cycle.
Unbalanced Load / Spin Protection
E21
Washer shows E21; drum does not spin or spin speed is very low.
Motor Drive Error
E23
Washer displays E23; drain pump triac or pump circuit error.
Drain Pump Control Fault
E3
Washer shows E3 and stops; drum does not rotate or rotates only briefly then stops.
Motor Overload / Motor Drive Fault
E30
Washer shows E30; door lock cannot be engaged or detected.
Door Locking Failure
E31
Washer displays E31; water level sensor signal is out of range.
Pressure Sensor Signal Error
E32
Washer shows E32; unbalanced load detected repeatedly, spin aborted.
Chronic Unbalance Detection
E33
Washer displays E33; heating and water level signals conflict (e.g., heater on with low water).
Heater and Water Level Conflict
E34
Washer shows E34; door lock and water level signals conflict (e.g., door open while full).
Door Lock / Water Level Conflict
E4
Washer displays E4 and will not start or stops filling; water level seems incorrect.
Water Level Sensor / Pressure Switch Error
E40
Washer displays E40; door is reported as open when starting a cycle.
Door Open Detection Error
E41
Washer shows E41; door lock cannot be unlocked at end of cycle.
Door Unlock Failure
E5
Washer shows E5; water does not fill or fills very slowly.
Water Inlet Timeout / Low Water Flow
E50
Washer displays E50; general motor error, drum may not turn or may jerk.
General Motor Fault
E51
Washer shows E51; motor triac or inverter short circuit.
Motor Power Device Short
E6
Washer displays E6; motor does not run or runs erratically.
Motor Tachometer / Speed Sensor Error
E60
Washer displays E60; general heating system error.
General Heater System Fault
E7
Washer shows E7 and will not start or stops unexpectedly; often related to lid/door status.
Lid / Door Switch Error
E8
Washer displays E8; water level is too high or overflows into the drum.
Overfill / Overflow Protection
E9
Washer shows E9; water leaks detected in base or abnormal water level behavior.
Leakage / Water Level Abnormality
E90
Washer shows E90; communication error between main control board and user interface or inverter.
Communication Failure
Symptom
Top-load washer agitator does not move, but the drum may spin.
Agitator Drive Failure (Top-Load)
Symptom
Washer does not spin at the end of the cycle; clothes are soaking wet.
No Spin / Spin Cycle Failure
Symptom
Washer door or lid is difficult to open or close; latch feels stiff.
Mechanical Door / Lid Alignment Issue
Symptom
Washer drum has excessive play and can be lifted significantly up and down.
Drum Support / Bearing Failure
Symptom
Washer emits a burning smell during operation.
Overheating Component / Friction
Symptom
Washer fills with water but does not agitate or tumble.
Wash Motor / Agitation Failure
Symptom
Washer has a strong moldy or musty odor inside the drum.
Biofilm / Mold Build-Up
Symptom
Washer intermittently stops mid-cycle and then resumes after some time.
Overheating Motor or Control / Intermittent Power
Symptom
Washer is very noisy during spin; banging or knocking sounds from the drum.
Excessive Vibration / Suspension Failure
Symptom
Washer leaks water from the front door area during wash or spin.
Door Gasket / Seal Leak
Symptom
Washer leaks water from underneath the cabinet.
Internal Hose or Pump Leak
Symptom
Washer leaves detergent residue or white streaks on clothes.
Poor Rinsing / Detergent Overuse
Symptom
Washer makes a grinding or scraping noise when the drum turns.
Foreign Object in Drum / Bearing Wear
Symptom
Washer powers on but will not start cycle when Start/Pause is pressed.
Start Command / User Interface Fault
Symptom
Washer takes much longer than expected to complete a cycle.
Extended Cycle Time / Control Logic Adjustment
Symptom
Washer will not power on at all; no lights or display response.
No Power / Dead Appliance
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E1 |
Washer stops mid-cycle and displays E1; water does not drain or drains very slowly.
|
Drainage Failure | View Details |
| E10 |
Washer displays E10; no water enters or fill is extremely slow at the beginning of the cycle.
|
Water Inlet Failure | View Details |
| E11 |
Washer shows E11; water does not drain within the expected time, often after rinse.
|
Drain Timeout | View Details |
| E12 |
Washer displays E12; heating function fails or water does not reach target temperature.
|
Heater Circuit Fault | View Details |
| E2 |
Washer displays E2 and will not spin; clothes remain very wet at the end of the cycle.
|
Unbalanced Load / Spin Protection | View Details |
| E21 |
Washer shows E21; drum does not spin or spin speed is very low.
|
Motor Drive Error | View Details |
| E23 |
Washer displays E23; drain pump triac or pump circuit error.
|
Drain Pump Control Fault | View Details |
| E3 |
Washer shows E3 and stops; drum does not rotate or rotates only briefly then stops.
|
Motor Overload / Motor Drive Fault | View Details |
| E30 |
Washer shows E30; door lock cannot be engaged or detected.
|
Door Locking Failure | View Details |
| E31 |
Washer displays E31; water level sensor signal is out of range.
|
Pressure Sensor Signal Error | View Details |
| E32 |
Washer shows E32; unbalanced load detected repeatedly, spin aborted.
|
Chronic Unbalance Detection | View Details |
| E33 |
Washer displays E33; heating and water level signals conflict (e.g., heater on with low water).
|
Heater and Water Level Conflict | View Details |
| E34 |
Washer shows E34; door lock and water level signals conflict (e.g., door open while full).
|
Door Lock / Water Level Conflict | View Details |
| E4 |
Washer displays E4 and will not start or stops filling; water level seems incorrect.
|
Water Level Sensor / Pressure Switch Error | View Details |
| E40 |
Washer displays E40; door is reported as open when starting a cycle.
|
Door Open Detection Error | View Details |
| E41 |
Washer shows E41; door lock cannot be unlocked at end of cycle.
|
Door Unlock Failure | View Details |
| E5 |
Washer shows E5; water does not fill or fills very slowly.
|
Water Inlet Timeout / Low Water Flow | View Details |
| E50 |
Washer displays E50; general motor error, drum may not turn or may jerk.
|
General Motor Fault | View Details |
| E51 |
Washer shows E51; motor triac or inverter short circuit.
|
Motor Power Device Short | View Details |
| E6 |
Washer displays E6; motor does not run or runs erratically.
|
Motor Tachometer / Speed Sensor Error | View Details |
| E60 |
Washer displays E60; general heating system error.
|
General Heater System Fault | View Details |
| E7 |
Washer shows E7 and will not start or stops unexpectedly; often related to lid/door status.
|
Lid / Door Switch Error | View Details |
| E8 |
Washer displays E8; water level is too high or overflows into the drum.
|
Overfill / Overflow Protection | View Details |
| E9 |
Washer shows E9; water leaks detected in base or abnormal water level behavior.
|
Leakage / Water Level Abnormality | View Details |
| E90 |
Washer shows E90; communication error between main control board and user interface or inverter.
|
Communication Failure | View Details |
| – |
Top-load washer agitator does not move, but the drum may spin.
|
Agitator Drive Failure (Top-Load) | View Details |
| – |
Washer does not spin at the end of the cycle; clothes are soaking wet.
|
No Spin / Spin Cycle Failure | View Details |
| – |
Washer door or lid is difficult to open or close; latch feels stiff.
|
Mechanical Door / Lid Alignment Issue | View Details |
| – |
Washer drum has excessive play and can be lifted significantly up and down.
|
Drum Support / Bearing Failure | View Details |
| – |
Washer emits a burning smell during operation.
|
Overheating Component / Friction | View Details |
| – |
Washer fills with water but does not agitate or tumble.
|
Wash Motor / Agitation Failure | View Details |
| – |
Washer has a strong moldy or musty odor inside the drum.
|
Biofilm / Mold Build-Up | View Details |
| – |
Washer intermittently stops mid-cycle and then resumes after some time.
|
Overheating Motor or Control / Intermittent Power | View Details |
| – |
Washer is very noisy during spin; banging or knocking sounds from the drum.
|
Excessive Vibration / Suspension Failure | View Details |
| – |
Washer leaks water from the front door area during wash or spin.
|
Door Gasket / Seal Leak | View Details |
| – |
Washer leaks water from underneath the cabinet.
|
Internal Hose or Pump Leak | View Details |
| – |
Washer leaves detergent residue or white streaks on clothes.
|
Poor Rinsing / Detergent Overuse | View Details |
| – |
Washer makes a grinding or scraping noise when the drum turns.
|
Foreign Object in Drum / Bearing Wear | View Details |
| – |
Washer powers on but will not start cycle when Start/Pause is pressed.
|
Start Command / User Interface Fault | View Details |
| – |
Washer takes much longer than expected to complete a cycle.
|
Extended Cycle Time / Control Logic Adjustment | View Details |
| – |
Washer will not power on at all; no lights or display response.
|
No Power / Dead Appliance | View Details |
No matching codes found
Advertisements