V-ZUG Washing Machines Error Codes

E01

Washer will not start; display shows E01 immediately after pressing Start

Door Lock / Interlock Fault

E02

Washer does not fill with water; E02 displayed shortly after cycle start

Water Inlet / Fill Fault

E03

Washer fails to drain; water remains in drum and E03 is displayed

Drain Pump / Drainage Fault

E04

Washer overfills or shows E04 with water level too high in drum

Water Level / Pressure Sensor Fault

E05

Washer does not heat water; cycle runs cold and E05 appears

Heating Circuit Fault

E06

Washer stops mid-cycle and displays E06; door may remain locked

Motor / Drive Fault

E07

Washer displays E07 and will not spin at high speed

Unbalanced Load / Spin Protection Fault

E08

Washer shows E08 and stops; often associated with water leakage into base

AquaStop / Leak Protection Activation

E09

Washer displays E09 and does not start or stops unexpectedly

Control Electronics / Communication Fault

E10

Washer shows E10 and does not take in softener or detergent correctly

Detergent Drawer / Dispenser Valve Fault

E11

Washer shows E11 and door cannot be opened at end of cycle

Door Unlock Fault

E12

Washer displays E12 and stops during rinse or spin; often with excessive foam

Foam / Suds Detection Fault

E13

Washer shows E13 and does not start; often related to door or safety system

Safety Interlock / Child Lock Fault

E20

Washer shows E20 and does not drain or spin properly

Extended Drain Time / Pump Performance Fault

E21

Washer displays E21 and drum does not rotate or rotates erratically

Motor Tachometer / Speed Feedback Fault

E22

Washer shows E22 and does not heat or complete cycles correctly

NTC Temperature Sensor Fault

E23

Washer displays E23 and may trip the household fuse or not start

Heater Earth Leakage / Short to Ground

E24

Washer shows E24 and stops; often related to door or water safety

Door / Water Safety Combined Fault

E30

Washer shows E30 and will not start or stops with water in drum

General Water System Fault

E40

Washer displays E40 and door symbol flashes; machine will not start

Door Not Properly Closed

E41

Washer shows E41; door appears closed but machine still reports door error

Door Lock Contact Fault

E50

Washer shows E50 and may not spin or wash; motor-related error

General Motor / Inverter Fault

E51

Washer displays E51 and stops during spin acceleration

Motor Power Stage Fault

E60

Washer shows E60; heating-related general error

General Heating System Fault

E70

Washer displays E70; temperature sensing error

Temperature Sensor Calibration / Range Fault

E90

Washer shows E90 and is unresponsive or behaves erratically

Configuration / Software Communication Fault

Symptom

Washer display is completely dead; no lights or response

No Power / Supply Fault

Symptom

Washer display works but program freezes mid-cycle without error code

Control Logic Hang / Sensor Timeout

Symptom

Washer does not dispense fabric softener; softener remains in drawer after cycle

Softener Compartment Siphon Failure

Symptom

Washer does not fill with enough water; clothes come out partially dry or not fully wet

Low Water Level / Underfilling

Symptom

Washer door or rubber seal has a strong moldy or musty odor

Biofilm / Mold Build-Up in Door Seal and Tub

Symptom

Washer drum does not turn at all during wash or spin, but no error code is shown

Drive System Failure Without Code

Symptom

Washer emits a burning smell during operation

Overheating Electrical or Mechanical Component

Symptom

Washer emits a sewage or rotten egg smell from the drum

Drain System Odor / Bacterial Growth

Symptom

Washer leaks water from the front under the door during wash or rinse

Door Seal (Gasket) Leak

Symptom

Washer leaks water from the rear or bottom during operation

Internal Hose or Pump Leak

Symptom

Washer leaves clothes very wet at the end of the cycle; spin seems weak

Poor Spin Performance

Symptom

Washer leaves detergent residues or white streaks on clothes

Poor Rinsing / Detergent Dissolution

Symptom

Washer makes loud banging or knocking noises during spin

Suspension / Shock Absorber Wear

Symptom

Washer overfills slightly and water can be seen in the door seal area during wash

High Water Level / Overfilling Without Code

Symptom

Washer produces a high-pitched squeal or grinding noise when spinning

Drum Bearing or Drive Pulley Fault

Symptom

Washer takes much longer than the displayed time to finish a cycle

Extended Cycle Time / Auto-Adjustment

Symptom

Washer vibrates excessively and moves across the floor during spin

Excessive Vibration / Installation Fault

Symptom

Washer will not start; display is on but Start button does nothing and no code appears

User Interface / Start Circuit Fault