Caple
Caple Ranges & Cooktops Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E1
Induction hob zone will not heat and displays E1 shortly after switching on.
Pan Detection / Cookware Recognition Fault
E2
Induction hob zone shuts down and shows E2 after a short period of heating.
Induction Zone Overheating / Thermal Sensor Fault
E3
Induction hob displays E3 and will not start heating on one or more zones.
Supply Voltage Out of Range / Overvoltage Protection
E4
Induction hob shows E4 and the affected zone cannot be used.
IGBT / Power Module Overcurrent Fault
E5
Induction hob displays E5 and beeps, zones refuse to start.
NTC Sensor Open Circuit / Temperature Sensor Failure
E6
Induction hob shows E6 and all zones are disabled.
Internal Communication Error Between Touch Control and Power Module
E7
Induction hob intermittently shows E7 and beeps when trying to adjust power levels.
Touch Slider / Keypad Calibration Error
E8
Induction hob shows E8 and one side (left or right group of zones) is inoperative.
Half‑Bridge / Side Power Module Failure
E9
Induction hob displays E9 and shuts down during operation.
Internal EEPROM / Configuration Error
F0
Gas hob with electronic ignition shows F0 on the display and burners will not ignite.
Ignition System General Fault
F1
Gas hob shows F1 and continuously clicks even when burners are lit.
Flame Detection / Ignition Switch Stuck
F2
Gas hob with digital display shows F2 and gas supply is cut off to all burners.
Flame Failure Device / Safety Valve Fault
F3
Electric ceramic hob shows F3 and one radiant zone does not heat.
Radiant Element Temperature Sensor Fault
F4
Electric ceramic hob shows F4 and multiple zones are disabled.
Power Relay / Triac Failure
F5
Electric hob shows F5 and beeps when trying to use the child lock or timer.
User Interface Logic / Lock Circuit Fault
F6
Electric hob shows F6 and shuts down when multiple zones are used.
Overcurrent / Load Management Fault
H
H or "Hot" remains displayed on the hob long after it has cooled.
Residual Heat Indicator Sensor Fault
Lo
Induction hob displays "Lo" and zones will not heat above a low setting.
Low Power / Demo Mode or Power Limitation Active
Symptom
Control knobs on gas hob are stiff or difficult to turn.
Seized Gas Tap / Valve
Symptom
Cooling fan runs continuously long after the hob has been turned off.
Cooling Fan Control / Temperature Sensor Issue
Symptom
Electric ceramic hob zone does not heat at all, no error code displayed.
Open Circuit Radiant Element or Switch
Symptom
Electric ceramic hob zone overheats and does not cycle off, causing very high temperatures.
Stuck Energy Regulator / Thermostat Failure
Symptom
Gas burner lights but goes out when the knob is released.
Flame Failure Device Not Holding
Symptom
Gas burner will not ignite or takes a long time to light, but other burners work normally.
Individual Burner Ignition Failure
Symptom
Gas hob makes loud popping or blowing noises when burners are on.
Burner Instability / Flame Lift
Symptom
Gas hob produces yellow, lazy flames or soot on pans.
Incorrect Combustion / Air–Gas Mixture Fault
Symptom
Gas smell around hob when burners are off.
Gas Leak at Hob Connections
Symptom
Hob causes interference with radio or Wi‑Fi when in use.
Electromagnetic Interference (EMI) from Hob
Symptom
Hob completely dead; no lights or response from any controls.
No Power / Supply Failure
Symptom
Hob controls unresponsive; no keys respond but power indicator is lit.
Frozen Touch Control Panel
Symptom
Hob emits a strong burning smell or visible smoke during use.
Overheating Wiring or Component Failure
Symptom
Hob glass is cracked or shattered but appliance still heats.
Damaged Ceramic Glass Top
Symptom
Hob vibrates loudly or buzzes excessively when induction zones are on.
Induction Acoustic Noise / Mechanical Resonance
Symptom
Induction hob clicks on and off rapidly and will not maintain a steady heat.
Intermittent Pan Detection / Power Modulation Fault
Symptom
Induction hob trips the household circuit breaker when a zone is turned on.
Short Circuit in Induction Power Stage
Symptom
Timer or display on hob is dim, flickering, or partially missing segments.
Display Module / Power Supply Fault
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E1 |
Induction hob zone will not heat and displays E1 shortly after switching on.
|
Pan Detection / Cookware Recognition Fault | View Details |
| E2 |
Induction hob zone shuts down and shows E2 after a short period of heating.
|
Induction Zone Overheating / Thermal Sensor Fault | View Details |
| E3 |
Induction hob displays E3 and will not start heating on one or more zones.
|
Supply Voltage Out of Range / Overvoltage Protection | View Details |
| E4 |
Induction hob shows E4 and the affected zone cannot be used.
|
IGBT / Power Module Overcurrent Fault | View Details |
| E5 |
Induction hob displays E5 and beeps, zones refuse to start.
|
NTC Sensor Open Circuit / Temperature Sensor Failure | View Details |
| E6 |
Induction hob shows E6 and all zones are disabled.
|
Internal Communication Error Between Touch Control and Power Module | View Details |
| E7 |
Induction hob intermittently shows E7 and beeps when trying to adjust power levels.
|
Touch Slider / Keypad Calibration Error | View Details |
| E8 |
Induction hob shows E8 and one side (left or right group of zones) is inoperative.
|
Half‑Bridge / Side Power Module Failure | View Details |
| E9 |
Induction hob displays E9 and shuts down during operation.
|
Internal EEPROM / Configuration Error | View Details |
| F0 |
Gas hob with electronic ignition shows F0 on the display and burners will not ignite.
|
Ignition System General Fault | View Details |
| F1 |
Gas hob shows F1 and continuously clicks even when burners are lit.
|
Flame Detection / Ignition Switch Stuck | View Details |
| F2 |
Gas hob with digital display shows F2 and gas supply is cut off to all burners.
|
Flame Failure Device / Safety Valve Fault | View Details |
| F3 |
Electric ceramic hob shows F3 and one radiant zone does not heat.
|
Radiant Element Temperature Sensor Fault | View Details |
| F4 |
Electric ceramic hob shows F4 and multiple zones are disabled.
|
Power Relay / Triac Failure | View Details |
| F5 |
Electric hob shows F5 and beeps when trying to use the child lock or timer.
|
User Interface Logic / Lock Circuit Fault | View Details |
| F6 |
Electric hob shows F6 and shuts down when multiple zones are used.
|
Overcurrent / Load Management Fault | View Details |
| H |
H or "Hot" remains displayed on the hob long after it has cooled.
|
Residual Heat Indicator Sensor Fault | View Details |
| Lo |
Induction hob displays "Lo" and zones will not heat above a low setting.
|
Low Power / Demo Mode or Power Limitation Active | View Details |
| – |
Control knobs on gas hob are stiff or difficult to turn.
|
Seized Gas Tap / Valve | View Details |
| – |
Cooling fan runs continuously long after the hob has been turned off.
|
Cooling Fan Control / Temperature Sensor Issue | View Details |
| – |
Electric ceramic hob zone does not heat at all, no error code displayed.
|
Open Circuit Radiant Element or Switch | View Details |
| – |
Electric ceramic hob zone overheats and does not cycle off, causing very high temperatures.
|
Stuck Energy Regulator / Thermostat Failure | View Details |
| – |
Gas burner lights but goes out when the knob is released.
|
Flame Failure Device Not Holding | View Details |
| – |
Gas burner will not ignite or takes a long time to light, but other burners work normally.
|
Individual Burner Ignition Failure | View Details |
| – |
Gas hob makes loud popping or blowing noises when burners are on.
|
Burner Instability / Flame Lift | View Details |
| – |
Gas hob produces yellow, lazy flames or soot on pans.
|
Incorrect Combustion / Air–Gas Mixture Fault | View Details |
| – |
Gas smell around hob when burners are off.
|
Gas Leak at Hob Connections | View Details |
| – |
Hob causes interference with radio or Wi‑Fi when in use.
|
Electromagnetic Interference (EMI) from Hob | View Details |
| – |
Hob completely dead; no lights or response from any controls.
|
No Power / Supply Failure | View Details |
| – |
Hob controls unresponsive; no keys respond but power indicator is lit.
|
Frozen Touch Control Panel | View Details |
| – |
Hob emits a strong burning smell or visible smoke during use.
|
Overheating Wiring or Component Failure | View Details |
| – |
Hob glass is cracked or shattered but appliance still heats.
|
Damaged Ceramic Glass Top | View Details |
| – |
Hob vibrates loudly or buzzes excessively when induction zones are on.
|
Induction Acoustic Noise / Mechanical Resonance | View Details |
| – |
Induction hob clicks on and off rapidly and will not maintain a steady heat.
|
Intermittent Pan Detection / Power Modulation Fault | View Details |
| – |
Induction hob trips the household circuit breaker when a zone is turned on.
|
Short Circuit in Induction Power Stage | View Details |
| – |
Timer or display on hob is dim, flickering, or partially missing segments.
|
Display Module / Power Supply Fault | View Details |
No matching codes found
Advertisements