Siemens Ranges & Cooktops Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
dE
Cooktop or range shows dE and controls are locked
Child Lock / Demo Mode Active
E0
Induction cooktop does not heat, display shows E0 on one or more zones
Cookware Detection / Pan Recognition Fault
E1
Induction cooktop zone shuts off and displays E1 shortly after switching on
Overheating Protection / Internal Temperature Sensor Fault
E2
Induction zone stops heating and E2 appears on the display
Overtemperature of Cooking Zone / Coil Overheat
E3
Induction cooktop displays E3 and does not heat on one or more zones
Supply Voltage Too High / Mains Overvoltage Detection
E4
Induction zone shows E4 and shuts down when trying to cook
Supply Voltage Too Low / Undervoltage Detection
E5
Induction cooktop displays E5 and beeps, zones do not heat
Electronics Overheating / Heat Sink Overtemperature
E6
Induction cooktop shows E6 on one or more zones and will not start heating
Internal Communication Error Between User Interface and Power Module
E7
Induction cooktop displays E7 and does not respond to touch controls
Touch Control Panel / Sensor Calibration Error
E8
Induction cooktop shows E8 on a specific zone, no heating on that zone
Induction Coil or Power Stage Fault
E9
Induction cooktop displays E9 and shuts down completely
Internal Electronics Fault / EEPROM or Configuration Error
Er22
Induction cooktop shows Er22 and beeps continuously, no response to touch
Touch Control Panel Hardware Error
Er42
Induction cooktop displays Er42, some or all zones inoperative
Configuration / Parameter Error Between Glass and Electronics
Er47
Induction cooktop shows Er47 on a specific zone
Cooking Zone Power Module Fault
Er55
Induction cooktop displays Er55 and will not start any zone
Internal Software / Firmware Error
F0
Gas cooktop with electronic ignition shows F0 on display (if equipped) and burners do not ignite automatically
Ignition System General Fault
F1
Gas range or cooktop shows F1 and beeps, oven or burners may be disabled
Touchpad / Keypad Stuck or Shorted
F2
Range oven section (on a Siemens range) shows F2 and shuts off heating
Oven Overtemperature Fault
F3
Range oven display shows F3 and will not heat
Oven Temperature Sensor Open Circuit
F4
Range oven shows F4 error and may overheat or not regulate temperature
Oven Temperature Sensor Short Circuit
F5
Range or cooktop display shows F5, some functions disabled
Communication Error Between Oven Control and Cooktop Module
Symptom
Clock or timer on Siemens range does not keep time or resets randomly
Electronic Timer / Control Power Supply Fault
Symptom
Continuous clicking from gas burners even when all knobs are in OFF position
Ignition Switch Stuck Closed / Moisture in Ignition System
Symptom
Cooktop controls do not respond, but display lights are on (no specific error code)
Control Lock Active or Touch Panel Unresponsive
Symptom
Cooktop glass is cracked or shattered
Glass Ceramic Top Damage
Symptom
Cooktop indicator light stays on even when all zones are off and cool
Residual Heat Indicator or Control Logic Fault
Symptom
Cooktop surface around burners or zones is excessively hot or discolored
Overheating of Surrounding Glass / Heat Transfer Issue
Symptom
Cooktop trips the circuit breaker or RCD when turned on
Electrical Short or Earth Leakage
Symptom
Electric radiant cooktop zone does not heat at all (no error code)
Radiant Heating Element Open Circuit
Symptom
Electric radiant zone heats only on highest setting or cannot be controlled
Infinite Switch / Power Control Failure
Symptom
Gas burner clicks (sparks) but does not light or takes a long time to ignite
Delayed Ignition / Poor Flame Establishment
Symptom
Gas burner flame is uneven, yellow, or noisy (lifting off the burner)
Incorrect Air-Gas Mixture / Burner Contamination
Symptom
Gas burner ignites but goes out when knob is released
Flame Supervision Device (Thermocouple) Failure
Symptom
Gas burner will not ignite (no clicking sound, no spark at electrode)
Ignition System Failure – No Spark
Symptom
Gas smell around Siemens cooktop when not in use
Gas Leak in Supply or Valve Assembly
Symptom
Induction cooktop makes loud buzzing or humming noise during operation
Induction Acoustic Noise / Coil Vibration
Symptom
Oven door on Siemens range does not close properly or heat escapes
Door Alignment / Seal Failure
Symptom
Oven temperature inaccurate (overheating or underheating) on Siemens range
Temperature Regulation Fault
Symptom
Range oven in Siemens range does not heat, but cooktop works normally
Oven Heating Circuit Failure
Symptom
Strong burning smell or smoke from cooktop or range during normal use
Overheating or Contamination on Heating Components
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| dE |
Cooktop or range shows dE and controls are locked
|
Child Lock / Demo Mode Active | View Details |
| E0 |
Induction cooktop does not heat, display shows E0 on one or more zones
|
Cookware Detection / Pan Recognition Fault | View Details |
| E1 |
Induction cooktop zone shuts off and displays E1 shortly after switching on
|
Overheating Protection / Internal Temperature Sensor Fault | View Details |
| E2 |
Induction zone stops heating and E2 appears on the display
|
Overtemperature of Cooking Zone / Coil Overheat | View Details |
| E3 |
Induction cooktop displays E3 and does not heat on one or more zones
|
Supply Voltage Too High / Mains Overvoltage Detection | View Details |
| E4 |
Induction zone shows E4 and shuts down when trying to cook
|
Supply Voltage Too Low / Undervoltage Detection | View Details |
| E5 |
Induction cooktop displays E5 and beeps, zones do not heat
|
Electronics Overheating / Heat Sink Overtemperature | View Details |
| E6 |
Induction cooktop shows E6 on one or more zones and will not start heating
|
Internal Communication Error Between User Interface and Power Module | View Details |
| E7 |
Induction cooktop displays E7 and does not respond to touch controls
|
Touch Control Panel / Sensor Calibration Error | View Details |
| E8 |
Induction cooktop shows E8 on a specific zone, no heating on that zone
|
Induction Coil or Power Stage Fault | View Details |
| E9 |
Induction cooktop displays E9 and shuts down completely
|
Internal Electronics Fault / EEPROM or Configuration Error | View Details |
| Er22 |
Induction cooktop shows Er22 and beeps continuously, no response to touch
|
Touch Control Panel Hardware Error | View Details |
| Er42 |
Induction cooktop displays Er42, some or all zones inoperative
|
Configuration / Parameter Error Between Glass and Electronics | View Details |
| Er47 |
Induction cooktop shows Er47 on a specific zone
|
Cooking Zone Power Module Fault | View Details |
| Er55 |
Induction cooktop displays Er55 and will not start any zone
|
Internal Software / Firmware Error | View Details |
| F0 |
Gas cooktop with electronic ignition shows F0 on display (if equipped) and burners do not ignite automatically
|
Ignition System General Fault | View Details |
| F1 |
Gas range or cooktop shows F1 and beeps, oven or burners may be disabled
|
Touchpad / Keypad Stuck or Shorted | View Details |
| F2 |
Range oven section (on a Siemens range) shows F2 and shuts off heating
|
Oven Overtemperature Fault | View Details |
| F3 |
Range oven display shows F3 and will not heat
|
Oven Temperature Sensor Open Circuit | View Details |
| F4 |
Range oven shows F4 error and may overheat or not regulate temperature
|
Oven Temperature Sensor Short Circuit | View Details |
| F5 |
Range or cooktop display shows F5, some functions disabled
|
Communication Error Between Oven Control and Cooktop Module | View Details |
| – |
Clock or timer on Siemens range does not keep time or resets randomly
|
Electronic Timer / Control Power Supply Fault | View Details |
| – |
Continuous clicking from gas burners even when all knobs are in OFF position
|
Ignition Switch Stuck Closed / Moisture in Ignition System | View Details |
| – |
Cooktop controls do not respond, but display lights are on (no specific error code)
|
Control Lock Active or Touch Panel Unresponsive | View Details |
| – |
Cooktop glass is cracked or shattered
|
Glass Ceramic Top Damage | View Details |
| – |
Cooktop indicator light stays on even when all zones are off and cool
|
Residual Heat Indicator or Control Logic Fault | View Details |
| – |
Cooktop surface around burners or zones is excessively hot or discolored
|
Overheating of Surrounding Glass / Heat Transfer Issue | View Details |
| – |
Cooktop trips the circuit breaker or RCD when turned on
|
Electrical Short or Earth Leakage | View Details |
| – |
Electric radiant cooktop zone does not heat at all (no error code)
|
Radiant Heating Element Open Circuit | View Details |
| – |
Electric radiant zone heats only on highest setting or cannot be controlled
|
Infinite Switch / Power Control Failure | View Details |
| – |
Gas burner clicks (sparks) but does not light or takes a long time to ignite
|
Delayed Ignition / Poor Flame Establishment | View Details |
| – |
Gas burner flame is uneven, yellow, or noisy (lifting off the burner)
|
Incorrect Air-Gas Mixture / Burner Contamination | View Details |
| – |
Gas burner ignites but goes out when knob is released
|
Flame Supervision Device (Thermocouple) Failure | View Details |
| – |
Gas burner will not ignite (no clicking sound, no spark at electrode)
|
Ignition System Failure – No Spark | View Details |
| – |
Gas smell around Siemens cooktop when not in use
|
Gas Leak in Supply or Valve Assembly | View Details |
| – |
Induction cooktop makes loud buzzing or humming noise during operation
|
Induction Acoustic Noise / Coil Vibration | View Details |
| – |
Oven door on Siemens range does not close properly or heat escapes
|
Door Alignment / Seal Failure | View Details |
| – |
Oven temperature inaccurate (overheating or underheating) on Siemens range
|
Temperature Regulation Fault | View Details |
| – |
Range oven in Siemens range does not heat, but cooktop works normally
|
Oven Heating Circuit Failure | View Details |
| – |
Strong burning smell or smoke from cooktop or range during normal use
|
Overheating or Contamination on Heating Components | View Details |
No matching codes found
Advertisements