Rosières
Rosières Washing Machines Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E01
Washer will not start a cycle and the door will not lock; E01 appears shortly after pressing Start.
Door Lock Circuit Failure
E02
Washer does not fill with water or fills very slowly; E02 appears after a few minutes from start.
Water Inlet Timeout / Fill Fault
E03
Washer stops with water remaining in the drum; E03 is displayed and the cycle will not continue to spin.
Drain Timeout / Pumping Fault
E04
Washer overfills or shows E04 and attempts to drain immediately after filling; may also show water in the drawer or leak from door.
Overfill / Pressure Switch Fault
E05
Washer stops during wash or rinse with E05; water may be cold even on hot programs.
Heating Circuit Failure
E06
Washer displays E06 and may not spin or may stop mid-cycle; sometimes accompanied by unusual motor noises.
Motor Tachometer / Speed Sensor Fault
E07
Washer shows E07 and will not spin at high speed; drum may turn slowly but final spin is not reached.
Unbalanced Load / Spin Protection Fault
E08
Washer displays E08 and the drum does not turn at all during wash or spin.
Motor Drive Failure
E09
Washer shows E09 and may trip the household breaker or stop immediately after starting a cycle.
Heater Short Circuit / Earth Leakage
E10
Washer displays E10 and does not take in water at the start of the cycle.
No Water Inlet Detected
E11
Washer shows E11 during or after filling; water level appears incorrect or machine may overfill/underfill.
Water Level Sensing Error
E12
Washer displays E12 and may stop during heating phase; water may be lukewarm or cold.
Temperature Sensor (NTC) Fault
E13
Washer shows E13 and may stop with water in the base tray; often accompanied by the drain pump running continuously.
Anti-Flood / Leak Detection Activated
E14
Washer displays E14 and may not respond to button presses or may behave erratically.
Control Panel / User Interface Communication Error
E15
Washer shows E15 and will not start; display may be blank or frozen.
Main Control Board Failure
E16
Washer displays E16 and the door remains locked at the end of the cycle.
Door Unlock Failure
E17
Washer shows E17 and may stop during spin; sometimes accompanied by loud knocking or excessive movement.
Excessive Vibration / Out-of-Balance Error
E18
Washer displays E18 and the cycle time does not advance; machine may appear to be stuck on one stage.
Program Timing / Sensor Feedback Error
E19
Washer shows E19 and may not respond correctly to selected programs; options may not be applied.
EEPROM / Program Memory Error
E20
Washer displays E20 and stops with water in the drum or fails to spin properly.
Drain / Spin Interlock Fault
Symptom
Washer display and lights flicker or reset during operation.
Intermittent Power / Electrical Noise
Symptom
Washer does not drain water at the end of the cycle; clothes remain soaked, but no error code is displayed.
Partial Drain Blockage
Symptom
Washer does not heat water; cycles complete but clothes are washed cold.
No Heating Without Error Code
Symptom
Washer does not spin or spins only very slowly; clothes come out very wet.
Spin Cycle Not Reached
Symptom
Washer does not start at all; no lights or display when the power button is pressed.
No Power / Supply Fault
Symptom
Washer door will not open at the end of the cycle, but no error code is shown.
Door Lock Stuck Closed
Symptom
Washer emits a bad smell (musty or sewer-like) from the drum or detergent drawer.
Biofilm / Bacterial Build-Up
Symptom
Washer emits a high-pitched squeal or scraping noise when the drum turns.
Foreign Object Between Drum and Tub
Symptom
Washer fills and drains repeatedly without progressing to wash.
Continuous Fill and Drain (Siphoning or Level Fault)
Symptom
Washer leaks water from the front door area during wash or rinse.
Door Gasket (Boot Seal) Leak
Symptom
Washer leaks water from underneath the cabinet, especially during drain or spin.
Internal Hose or Pump Leak
Symptom
Washer leaves black or greasy marks on clothes.
Contamination from Drum or Bearings
Symptom
Washer leaves clothes with detergent residue or not properly rinsed.
Poor Rinsing Performance
Symptom
Washer makes a loud roaring or rumbling noise during spin; noise increases with speed.
Drum Bearing Failure
Symptom
Washer makes loud banging or knocking noises during spin; machine may move across the floor.
Suspension / Shock Absorber Wear
Symptom
Washer overflows from the detergent drawer during fill.
Drawer Overflow / Venting Issue
Symptom
Washer powers on but will not start a cycle; Start button unresponsive, no error code shown.
User Interface / Start Circuit Issue
Symptom
Washer takes much longer than the displayed time to complete a cycle.
Extended Cycle Time / Auto-Correction
Symptom
Washer vibrates excessively even with small loads and correct leveling.
Chronic Vibration / Structural Issue
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E01 |
Washer will not start a cycle and the door will not lock; E01 appears shortly after pressing Start.
|
Door Lock Circuit Failure | View Details |
| E02 |
Washer does not fill with water or fills very slowly; E02 appears after a few minutes from start.
|
Water Inlet Timeout / Fill Fault | View Details |
| E03 |
Washer stops with water remaining in the drum; E03 is displayed and the cycle will not continue to spin.
|
Drain Timeout / Pumping Fault | View Details |
| E04 |
Washer overfills or shows E04 and attempts to drain immediately after filling; may also show water in the drawer or leak from door.
|
Overfill / Pressure Switch Fault | View Details |
| E05 |
Washer stops during wash or rinse with E05; water may be cold even on hot programs.
|
Heating Circuit Failure | View Details |
| E06 |
Washer displays E06 and may not spin or may stop mid-cycle; sometimes accompanied by unusual motor noises.
|
Motor Tachometer / Speed Sensor Fault | View Details |
| E07 |
Washer shows E07 and will not spin at high speed; drum may turn slowly but final spin is not reached.
|
Unbalanced Load / Spin Protection Fault | View Details |
| E08 |
Washer displays E08 and the drum does not turn at all during wash or spin.
|
Motor Drive Failure | View Details |
| E09 |
Washer shows E09 and may trip the household breaker or stop immediately after starting a cycle.
|
Heater Short Circuit / Earth Leakage | View Details |
| E10 |
Washer displays E10 and does not take in water at the start of the cycle.
|
No Water Inlet Detected | View Details |
| E11 |
Washer shows E11 during or after filling; water level appears incorrect or machine may overfill/underfill.
|
Water Level Sensing Error | View Details |
| E12 |
Washer displays E12 and may stop during heating phase; water may be lukewarm or cold.
|
Temperature Sensor (NTC) Fault | View Details |
| E13 |
Washer shows E13 and may stop with water in the base tray; often accompanied by the drain pump running continuously.
|
Anti-Flood / Leak Detection Activated | View Details |
| E14 |
Washer displays E14 and may not respond to button presses or may behave erratically.
|
Control Panel / User Interface Communication Error | View Details |
| E15 |
Washer shows E15 and will not start; display may be blank or frozen.
|
Main Control Board Failure | View Details |
| E16 |
Washer displays E16 and the door remains locked at the end of the cycle.
|
Door Unlock Failure | View Details |
| E17 |
Washer shows E17 and may stop during spin; sometimes accompanied by loud knocking or excessive movement.
|
Excessive Vibration / Out-of-Balance Error | View Details |
| E18 |
Washer displays E18 and the cycle time does not advance; machine may appear to be stuck on one stage.
|
Program Timing / Sensor Feedback Error | View Details |
| E19 |
Washer shows E19 and may not respond correctly to selected programs; options may not be applied.
|
EEPROM / Program Memory Error | View Details |
| E20 |
Washer displays E20 and stops with water in the drum or fails to spin properly.
|
Drain / Spin Interlock Fault | View Details |
| – |
Washer display and lights flicker or reset during operation.
|
Intermittent Power / Electrical Noise | View Details |
| – |
Washer does not drain water at the end of the cycle; clothes remain soaked, but no error code is displayed.
|
Partial Drain Blockage | View Details |
| – |
Washer does not heat water; cycles complete but clothes are washed cold.
|
No Heating Without Error Code | View Details |
| – |
Washer does not spin or spins only very slowly; clothes come out very wet.
|
Spin Cycle Not Reached | View Details |
| – |
Washer does not start at all; no lights or display when the power button is pressed.
|
No Power / Supply Fault | View Details |
| – |
Washer door will not open at the end of the cycle, but no error code is shown.
|
Door Lock Stuck Closed | View Details |
| – |
Washer emits a bad smell (musty or sewer-like) from the drum or detergent drawer.
|
Biofilm / Bacterial Build-Up | View Details |
| – |
Washer emits a high-pitched squeal or scraping noise when the drum turns.
|
Foreign Object Between Drum and Tub | View Details |
| – |
Washer fills and drains repeatedly without progressing to wash.
|
Continuous Fill and Drain (Siphoning or Level Fault) | View Details |
| – |
Washer leaks water from the front door area during wash or rinse.
|
Door Gasket (Boot Seal) Leak | View Details |
| – |
Washer leaks water from underneath the cabinet, especially during drain or spin.
|
Internal Hose or Pump Leak | View Details |
| – |
Washer leaves black or greasy marks on clothes.
|
Contamination from Drum or Bearings | View Details |
| – |
Washer leaves clothes with detergent residue or not properly rinsed.
|
Poor Rinsing Performance | View Details |
| – |
Washer makes a loud roaring or rumbling noise during spin; noise increases with speed.
|
Drum Bearing Failure | View Details |
| – |
Washer makes loud banging or knocking noises during spin; machine may move across the floor.
|
Suspension / Shock Absorber Wear | View Details |
| – |
Washer overflows from the detergent drawer during fill.
|
Drawer Overflow / Venting Issue | View Details |
| – |
Washer powers on but will not start a cycle; Start button unresponsive, no error code shown.
|
User Interface / Start Circuit Issue | View Details |
| – |
Washer takes much longer than the displayed time to complete a cycle.
|
Extended Cycle Time / Auto-Correction | View Details |
| – |
Washer vibrates excessively even with small loads and correct leveling.
|
Chronic Vibration / Structural Issue | View Details |
No matching codes found
Advertisements