Amica Dishwashers Error Codes

E1

Dishwasher does not fill with water, cycle stops shortly after start and E1 is displayed

Water Inlet Timeout / No Fill

E10

Dishwasher displays E10 and may not complete the program, often associated with drying issues

NTC Temperature Sensor Fault

E11

Dishwasher shows E11 and may not start or may stop shortly after starting

Door Lock / Door Switch Error

E12

Dishwasher displays E12, often associated with poor drying or fan noise issues

Drying Fan / Ventilation Fault

E13

Dishwasher shows E13 and may stop during the wash cycle

Circulation Pump Overload / Motor Error

E14

Dishwasher displays E14 and may not fill correctly or may stop shortly after filling

Water Distribution / Diverter Valve Error

E15

Dishwasher shows E15 and may continuously run the drain pump

Base Leak / Anti-Flood Triggered (Variant Code)

E16

Dishwasher displays E16 and may not start the wash cycle properly

Inlet Valve Electrical Fault

E17

Dishwasher shows E17, often associated with too much water or rapid filling

Overfill / High Water Level Detected Quickly

E18

Dishwasher displays E18 and does not take in enough water

Insufficient Water / Low Fill

E19

Dishwasher shows E19 and may have issues switching water between spray arms

Diverter Valve / Regeneration Valve Error

E2

Dishwasher fills but does not heat water, program runs unusually long and E2 appears

Heating Circuit Failure

E20

Dishwasher displays E20 and may not drain or may stop with water in the tub

Drain Pump Electrical Fault

E21

Dishwasher shows E21 and may not wash properly, with weak or no spray

Circulation Pump Electrical Fault

E22

Dishwasher displays E22 and may have standing water or poor drainage at the end of cycle

Filter / Sump Blockage Detected

E23

Dishwasher shows E23 and will not drain properly

Drain Pump Failure (Specific Code)

E24

Dishwasher displays E24 and may not drain or may abort at the start of the program

Drainage / Hose Blockage Error

E25

Dishwasher shows E25 and will not drain, often with a humming noise from the base

Drain Pump Blocked / Impeller Jammed

E3

Dishwasher does not drain, standing water remains in the tub and E3 is displayed

Drain Pump or Drainage Fault

E30

Dishwasher shows E30 and will not start or stops with alarm

General Safety / Flooding Error (Model-Dependent)

E4

Dishwasher stops mid-cycle, attempts to drain continuously, and E4 is shown

Anti-Flood / Overflow Protection Activated

E5

Dishwasher fills with too much water, water level rises above normal and E5 appears

Overfill / Water Level Sensor Fault

E6

Dishwasher stops and displays E6, often early in the cycle

Water Level Sensor / Pressure Switch Error

E7

Dishwasher shows E7 and may not start or may stop shortly after filling

Flow Meter / Water Intake Measurement Error

E8

Dishwasher displays E8 and may have poor washing performance or stop mid-cycle

Circulation Pump / Wash Pump Fault

E9

Dishwasher shows E9 and may stop during heating or drying phase

Heater Relay / Control Board Heating Control Error

Symptom

Detergent tablet remains in the dispenser at the end of the cycle

Detergent Dispenser / Spray Coverage Issue

Symptom

Dishes come out dirty, with food residues stuck on plates and glasses

Poor Wash Performance / Insufficient Spray Pressure

Symptom

Dishwasher does not dry dishes properly; items remain wet at end of cycle

Poor Drying Performance

Symptom

Dishwasher door drops down quickly or will not stay in intermediate positions

Door Spring / Hinge Cable Failure

Symptom

Dishwasher door is hard to close or misaligned with adjacent cabinets

Door Alignment / Hinge or Leveling Issue

Symptom

Dishwasher has a bad smell even when empty

Odor / Bacterial Growth in Sump and Hoses

Symptom

Dishwasher interior remains cold during wash, but no heating error code appears

Reduced Heating / Thermostat or Sensor Drift

Symptom

Dishwasher is very noisy during operation, with grinding or rattling sounds

Mechanical Noise / Pump or Spray Arm Interference

Symptom

Dishwasher leaks from the side or rear, water visible under the machine

Internal Hose or Pump Seal Leak

Symptom

Dishwasher leaks water from the bottom front of the door during the wash cycle

Door Gasket / Lower Door Seal Failure

Symptom

Dishwasher stops mid-cycle and does not resume, but no error code is shown

Intermittent Power or Overheating Component

Symptom

Dishwasher vibrates excessively or moves during operation

Excessive Vibration / Installation Issue

Symptom

Dishwasher will not start, display is on but program does not begin when Start is pressed

User Interface / Door Lock Not Engaged

Symptom

Dishwasher will not start, no lights or display

No Power / Main Supply Issue

Symptom

Rust-colored stains or pitting on cutlery and metal items

Corrosion / Chemical Attack

Symptom

Water remains in the bottom of the dishwasher after the cycle, but no error code is shown

Partial Drain / Siphon or Installation Issue

Symptom

White film or spots on glasses and dishes after the cycle

Limescale Deposits / Poor Rinse