Dyson Humidifiers & Dehumidifiers Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
F1
Dyson humidifier will not power on, display remains blank, no response to power button or remote
Main Power Supply / Control Board Fault
F10
Dyson humidifier shows F10 and shuts down, often after a few minutes of operation
Internal Leak / Water Ingress Detection
F11
Dyson humidifier displays F11 and does not respond correctly to remote or app commands
Communication / Control Interface Fault
F12
Dyson humidifier shows F12 and will not start, often after a power surge or outage
Firmware / Internal Memory Fault
F13
Dyson humidifier displays F13 and stops, often when room is very cold or very hot
Ambient Temperature Out of Range / Sensor Calibration Fault
F14
Dyson humidifier shows F14 and will not start misting, even though tank is full and seated
Tank Presence / Interlock Switch Fault
F15
Dyson humidifier displays F15 and stops, often with unusual noises from the base
Internal Mechanical Jam / Drive Fault
F16
Dyson humidifier shows F16 and humidity control is erratic or unresponsive
Control Panel / User Interface Fault
F2
Dyson humidifier powers on but immediately shows F2 and shuts down, no mist output
Ultrasonic Transducer / Atomizer Fault
F3
Dyson humidifier displays F3 and will not start misting, fan may still run briefly
Water Level Sensing Fault
F4
Dyson humidifier shows F4 and stops operation, often after a short run time
Overheat / Temperature Sensor Fault
F5
Dyson humidifier displays F5 and will not run UV or misting cycle
UV-C Sterilization System Fault
F6
Dyson humidifier shows F6 and stops, often accompanied by unusual fan behavior
Fan Motor / Airflow Fault
F7
Dyson humidifier displays F7 and refuses to start, often after being moved or tipped
Tilt / Tip-Over Sensor Fault
F8
Dyson humidifier shows F8 and stops, often associated with very low or no humidity output despite water in tank
Humidity Sensor / RH Feedback Fault
F9
Dyson humidifier displays F9 and will not start misting cycle, even with full tank
Water Pump / Circulation Fault
Symptom
Dyson humidifier base feels unusually warm or hot to the touch during normal operation
Abnormal Base Heating
Symptom
Dyson humidifier causes nearby surfaces or windows to become excessively wet or condense
Localized Over-Humidification / Poor Mist Distribution
Symptom
Dyson humidifier continues to run even when the room feels very humid, overshooting the set humidity
Humidity Control Overshoot
Symptom
Dyson humidifier dehumidifier combo unit blows warm air but does not reduce humidity
Ineffective Dehumidification (Combo Unit)
Symptom
Dyson humidifier dehumidifier mode (for combo models) does not remove moisture, water tank remains empty
Dehumidification Failure (Combo Unit)
Symptom
Dyson humidifier display is completely blank but unit still seems to run (fan and mist present)
Display Module Failure
Symptom
Dyson humidifier display or indicator lights flicker or dim randomly during operation
Display / Power Stability Issue
Symptom
Dyson humidifier emits a musty or moldy smell during operation
Microbial Contamination of Water Path
Symptom
Dyson humidifier leaks water onto the floor or furniture from around the base or tank area
External Water Leak
Symptom
Dyson humidifier makes loud buzzing or rattling noises during operation
Mechanical Noise / Vibration Fault
Symptom
Dyson humidifier produces very weak mist output even on maximum setting, room humidity barely increases
Reduced Humidification Performance
Symptom
Dyson humidifier remote control does not work, but unit operates from onboard controls
Remote Control Communication Failure
Symptom
Dyson humidifier runs but produces no mist at all, fan operates normally, no error code displayed
Ultrasonic Output Loss Without Code
Symptom
Dyson humidifier shows visible white dust settling on nearby surfaces
Mineral Dust Emission
Symptom
Dyson humidifier shows water in the tank but indicates low water or stops as if empty (no specific code)
False Empty Tank Detection
Symptom
Dyson humidifier stops producing mist but fan continues to run intermittently, then resumes later
Intermittent Misting / Thermal Cycling
Symptom
Dyson humidifier turns off by itself after a short time, even though the tank is full and settings are normal
Unexpected Auto Shutoff
Symptom
Dyson humidifier vibrates excessively or walks across the surface during operation
Excessive Vibration
Symptom
Dyson humidifier water tank is difficult to remove or install, sometimes causing improper operation
Tank Engagement / Mechanical Fit Issue
Symptom
Dyson humidifier will not turn on or respond, but outlet and cord are confirmed good
Internal Power Distribution Failure
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| F1 |
Dyson humidifier will not power on, display remains blank, no response to power button or remote
|
Main Power Supply / Control Board Fault | View Details |
| F10 |
Dyson humidifier shows F10 and shuts down, often after a few minutes of operation
|
Internal Leak / Water Ingress Detection | View Details |
| F11 |
Dyson humidifier displays F11 and does not respond correctly to remote or app commands
|
Communication / Control Interface Fault | View Details |
| F12 |
Dyson humidifier shows F12 and will not start, often after a power surge or outage
|
Firmware / Internal Memory Fault | View Details |
| F13 |
Dyson humidifier displays F13 and stops, often when room is very cold or very hot
|
Ambient Temperature Out of Range / Sensor Calibration Fault | View Details |
| F14 |
Dyson humidifier shows F14 and will not start misting, even though tank is full and seated
|
Tank Presence / Interlock Switch Fault | View Details |
| F15 |
Dyson humidifier displays F15 and stops, often with unusual noises from the base
|
Internal Mechanical Jam / Drive Fault | View Details |
| F16 |
Dyson humidifier shows F16 and humidity control is erratic or unresponsive
|
Control Panel / User Interface Fault | View Details |
| F2 |
Dyson humidifier powers on but immediately shows F2 and shuts down, no mist output
|
Ultrasonic Transducer / Atomizer Fault | View Details |
| F3 |
Dyson humidifier displays F3 and will not start misting, fan may still run briefly
|
Water Level Sensing Fault | View Details |
| F4 |
Dyson humidifier shows F4 and stops operation, often after a short run time
|
Overheat / Temperature Sensor Fault | View Details |
| F5 |
Dyson humidifier displays F5 and will not run UV or misting cycle
|
UV-C Sterilization System Fault | View Details |
| F6 |
Dyson humidifier shows F6 and stops, often accompanied by unusual fan behavior
|
Fan Motor / Airflow Fault | View Details |
| F7 |
Dyson humidifier displays F7 and refuses to start, often after being moved or tipped
|
Tilt / Tip-Over Sensor Fault | View Details |
| F8 |
Dyson humidifier shows F8 and stops, often associated with very low or no humidity output despite water in tank
|
Humidity Sensor / RH Feedback Fault | View Details |
| F9 |
Dyson humidifier displays F9 and will not start misting cycle, even with full tank
|
Water Pump / Circulation Fault | View Details |
| – |
Dyson humidifier base feels unusually warm or hot to the touch during normal operation
|
Abnormal Base Heating | View Details |
| – |
Dyson humidifier causes nearby surfaces or windows to become excessively wet or condense
|
Localized Over-Humidification / Poor Mist Distribution | View Details |
| – |
Dyson humidifier continues to run even when the room feels very humid, overshooting the set humidity
|
Humidity Control Overshoot | View Details |
| – |
Dyson humidifier dehumidifier combo unit blows warm air but does not reduce humidity
|
Ineffective Dehumidification (Combo Unit) | View Details |
| – |
Dyson humidifier dehumidifier mode (for combo models) does not remove moisture, water tank remains empty
|
Dehumidification Failure (Combo Unit) | View Details |
| – |
Dyson humidifier display is completely blank but unit still seems to run (fan and mist present)
|
Display Module Failure | View Details |
| – |
Dyson humidifier display or indicator lights flicker or dim randomly during operation
|
Display / Power Stability Issue | View Details |
| – |
Dyson humidifier emits a musty or moldy smell during operation
|
Microbial Contamination of Water Path | View Details |
| – |
Dyson humidifier leaks water onto the floor or furniture from around the base or tank area
|
External Water Leak | View Details |
| – |
Dyson humidifier makes loud buzzing or rattling noises during operation
|
Mechanical Noise / Vibration Fault | View Details |
| – |
Dyson humidifier produces very weak mist output even on maximum setting, room humidity barely increases
|
Reduced Humidification Performance | View Details |
| – |
Dyson humidifier remote control does not work, but unit operates from onboard controls
|
Remote Control Communication Failure | View Details |
| – |
Dyson humidifier runs but produces no mist at all, fan operates normally, no error code displayed
|
Ultrasonic Output Loss Without Code | View Details |
| – |
Dyson humidifier shows visible white dust settling on nearby surfaces
|
Mineral Dust Emission | View Details |
| – |
Dyson humidifier shows water in the tank but indicates low water or stops as if empty (no specific code)
|
False Empty Tank Detection | View Details |
| – |
Dyson humidifier stops producing mist but fan continues to run intermittently, then resumes later
|
Intermittent Misting / Thermal Cycling | View Details |
| – |
Dyson humidifier turns off by itself after a short time, even though the tank is full and settings are normal
|
Unexpected Auto Shutoff | View Details |
| – |
Dyson humidifier vibrates excessively or walks across the surface during operation
|
Excessive Vibration | View Details |
| – |
Dyson humidifier water tank is difficult to remove or install, sometimes causing improper operation
|
Tank Engagement / Mechanical Fit Issue | View Details |
| – |
Dyson humidifier will not turn on or respond, but outlet and cord are confirmed good
|
Internal Power Distribution Failure | View Details |
No matching codes found
Advertisements