Arcelik Dishwashers Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E01
Dishwasher does not fill with water; cycle starts then quickly stops and displays E01.
Water Inlet Failure
E02
Dishwasher fills but does not heat water; cycles take unusually long and E02 is displayed.
Heating Circuit Failure
E03
Dishwasher does not drain; standing water remains in the tub and E03 is shown.
Drain Pump or Drainage System Failure
E04
Dishwasher overfills or stops mid-cycle with water level too high; E04 appears on the display.
Overfill / Water Level Sensing Error
E05
Dishwasher stops shortly after starting; E05 is displayed and no spraying occurs.
Circulation Pump Failure
E06
Dishwasher door appears closed but cycle will not start; E06 is shown.
Door Lock / Door Switch Error
E07
Dishwasher stops mid-cycle and displays E07; sometimes accompanied by unusual noises from the sump area.
Sump Level / Turbidity Sensor Error
E08
Dishwasher displays E08 and dishes remain dirty; spray arms may not rotate properly.
Low Water Level / Circulation Pressure Error
E09
Dishwasher shows E09 and does not complete the drying phase; dishes come out wet and cold.
Drying System / Heater Error
E10
Dishwasher displays E10 and stops; often occurs during filling or rinsing stages.
Flow Meter / Water Intake Measurement Error
E11
Dishwasher shows E11 and may stop during heating; water may overheat or remain cold.
NTC Temperature Sensor Error
E12
Dishwasher displays E12 and may stop with water remaining in the tub; sometimes accompanied by unusual pump behavior.
Sump Water Level / Overflow Sensor Error
E13
Dishwasher shows E13 and may stop during the wash; sometimes associated with irregular water levels.
Pressure Switch Calibration / Signal Error
E14
Dishwasher displays E14 and may not start or may stop shortly after starting.
Control Panel / User Interface Communication Error
E15
Dishwasher shows E15 and will not start; often the drain pump runs continuously.
Anti-Flood System Activated (Leak Detected)
E16
Dishwasher displays E16 and may not fill correctly; sometimes fills continuously or not at all.
Inlet Valve / Aquastop Error
E17
Dishwasher shows E17 and may stop during the wash; sometimes associated with irregular spray pressure.
Circulation Pump Speed / Feedback Error
E18
Dishwasher displays E18 and may not start; sometimes buttons are unresponsive.
User Interface Key / Button Error
E19
Dishwasher shows E19 and may stop during program changes or when switching functions.
Diverter Valve / Regeneration Valve Error
E20
Dishwasher displays E20 and may not complete the cycle; often associated with unusual noises from the base.
Motor / Pump General Error
Symptom
Dishwasher display and lights flicker or reset during operation.
Unstable Power / Control Board Supply Issue
Symptom
Dishwasher displays unusually long cycle times without showing an error code.
Extended Cycle Duration / Sensor or Heating Inefficiency
Symptom
Dishwasher does not dry dishes properly; items come out wet and cool, but no error code is shown.
Poor Drying Performance
Symptom
Dishwasher door drops down quickly or will not stay in the partially open position.
Door Spring / Hinge Cable Failure
Symptom
Dishwasher door is difficult to close or appears misaligned with the cabinet.
Door Alignment / Hinge Issue
Symptom
Dishwasher fills and runs but dishes come out dirty; food residues remain on plates and glasses.
Poor Wash Performance
Symptom
Dishwasher interior and dishes smell bad, with persistent odors even after cycles.
Odor / Bacterial Growth in Sump and Hoses
Symptom
Dishwasher intermittently stops mid-cycle and resumes after some time, with no error code.
Thermal Overload / Overheating Protection
Symptom
Dishwasher is very noisy during operation; grinding, rattling, or humming sounds are heard.
Mechanical Noise / Pump or Spray Arm Interference
Symptom
Dishwasher leaks water from the front bottom of the door.
Door Seal / Spray Pattern Leak
Symptom
Dishwasher leaks water from underneath the cabinet.
Base Leak / Internal Hose or Sump Leak
Symptom
Dishwasher leaves detergent tablet partially undissolved in the dispenser.
Detergent Dispenser / Spray Coverage Issue
Symptom
Dishwasher leaves white film or spots on dishes and glassware.
Limescale / Detergent Residue
Symptom
Dishwasher powers on but will not start any program; Start button beeps or flashes but cycle does not begin.
Start Inhibit / Door or Program Lockout
Symptom
Dishwasher trips the household circuit breaker or RCD during operation.
Electrical Short / Earth Leakage
Symptom
Dishwasher vibrates excessively or moves during operation.
Excessive Vibration / Installation Issue
Symptom
Dishwasher will not power on at all; no lights or display, completely dead.
No Power / Main Supply Failure
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E01 |
Dishwasher does not fill with water; cycle starts then quickly stops and displays E01.
|
Water Inlet Failure | View Details |
| E02 |
Dishwasher fills but does not heat water; cycles take unusually long and E02 is displayed.
|
Heating Circuit Failure | View Details |
| E03 |
Dishwasher does not drain; standing water remains in the tub and E03 is shown.
|
Drain Pump or Drainage System Failure | View Details |
| E04 |
Dishwasher overfills or stops mid-cycle with water level too high; E04 appears on the display.
|
Overfill / Water Level Sensing Error | View Details |
| E05 |
Dishwasher stops shortly after starting; E05 is displayed and no spraying occurs.
|
Circulation Pump Failure | View Details |
| E06 |
Dishwasher door appears closed but cycle will not start; E06 is shown.
|
Door Lock / Door Switch Error | View Details |
| E07 |
Dishwasher stops mid-cycle and displays E07; sometimes accompanied by unusual noises from the sump area.
|
Sump Level / Turbidity Sensor Error | View Details |
| E08 |
Dishwasher displays E08 and dishes remain dirty; spray arms may not rotate properly.
|
Low Water Level / Circulation Pressure Error | View Details |
| E09 |
Dishwasher shows E09 and does not complete the drying phase; dishes come out wet and cold.
|
Drying System / Heater Error | View Details |
| E10 |
Dishwasher displays E10 and stops; often occurs during filling or rinsing stages.
|
Flow Meter / Water Intake Measurement Error | View Details |
| E11 |
Dishwasher shows E11 and may stop during heating; water may overheat or remain cold.
|
NTC Temperature Sensor Error | View Details |
| E12 |
Dishwasher displays E12 and may stop with water remaining in the tub; sometimes accompanied by unusual pump behavior.
|
Sump Water Level / Overflow Sensor Error | View Details |
| E13 |
Dishwasher shows E13 and may stop during the wash; sometimes associated with irregular water levels.
|
Pressure Switch Calibration / Signal Error | View Details |
| E14 |
Dishwasher displays E14 and may not start or may stop shortly after starting.
|
Control Panel / User Interface Communication Error | View Details |
| E15 |
Dishwasher shows E15 and will not start; often the drain pump runs continuously.
|
Anti-Flood System Activated (Leak Detected) | View Details |
| E16 |
Dishwasher displays E16 and may not fill correctly; sometimes fills continuously or not at all.
|
Inlet Valve / Aquastop Error | View Details |
| E17 |
Dishwasher shows E17 and may stop during the wash; sometimes associated with irregular spray pressure.
|
Circulation Pump Speed / Feedback Error | View Details |
| E18 |
Dishwasher displays E18 and may not start; sometimes buttons are unresponsive.
|
User Interface Key / Button Error | View Details |
| E19 |
Dishwasher shows E19 and may stop during program changes or when switching functions.
|
Diverter Valve / Regeneration Valve Error | View Details |
| E20 |
Dishwasher displays E20 and may not complete the cycle; often associated with unusual noises from the base.
|
Motor / Pump General Error | View Details |
| – |
Dishwasher display and lights flicker or reset during operation.
|
Unstable Power / Control Board Supply Issue | View Details |
| – |
Dishwasher displays unusually long cycle times without showing an error code.
|
Extended Cycle Duration / Sensor or Heating Inefficiency | View Details |
| – |
Dishwasher does not dry dishes properly; items come out wet and cool, but no error code is shown.
|
Poor Drying Performance | View Details |
| – |
Dishwasher door drops down quickly or will not stay in the partially open position.
|
Door Spring / Hinge Cable Failure | View Details |
| – |
Dishwasher door is difficult to close or appears misaligned with the cabinet.
|
Door Alignment / Hinge Issue | View Details |
| – |
Dishwasher fills and runs but dishes come out dirty; food residues remain on plates and glasses.
|
Poor Wash Performance | View Details |
| – |
Dishwasher interior and dishes smell bad, with persistent odors even after cycles.
|
Odor / Bacterial Growth in Sump and Hoses | View Details |
| – |
Dishwasher intermittently stops mid-cycle and resumes after some time, with no error code.
|
Thermal Overload / Overheating Protection | View Details |
| – |
Dishwasher is very noisy during operation; grinding, rattling, or humming sounds are heard.
|
Mechanical Noise / Pump or Spray Arm Interference | View Details |
| – |
Dishwasher leaks water from the front bottom of the door.
|
Door Seal / Spray Pattern Leak | View Details |
| – |
Dishwasher leaks water from underneath the cabinet.
|
Base Leak / Internal Hose or Sump Leak | View Details |
| – |
Dishwasher leaves detergent tablet partially undissolved in the dispenser.
|
Detergent Dispenser / Spray Coverage Issue | View Details |
| – |
Dishwasher leaves white film or spots on dishes and glassware.
|
Limescale / Detergent Residue | View Details |
| – |
Dishwasher powers on but will not start any program; Start button beeps or flashes but cycle does not begin.
|
Start Inhibit / Door or Program Lockout | View Details |
| – |
Dishwasher trips the household circuit breaker or RCD during operation.
|
Electrical Short / Earth Leakage | View Details |
| – |
Dishwasher vibrates excessively or moves during operation.
|
Excessive Vibration / Installation Issue | View Details |
| – |
Dishwasher will not power on at all; no lights or display, completely dead.
|
No Power / Main Supply Failure | View Details |
No matching codes found
Advertisements