CDA
CDA Dishwashers Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E1
Dishwasher will not fill with water, cycle stops shortly after start and E1 is displayed on the control panel.
Water Inlet Timeout / No Fill Detected
E10
Dishwasher displays E10 and may not start or may stop shortly after starting, sometimes with no water entering.
Water Inlet Valve Electrical Fault
E11
Dishwasher shows E11 and may not complete cycles; sometimes associated with erratic filling or draining behaviour.
Main Control Board Communication / Internal Error
E12
Dishwasher displays E12 and may have poor drying performance or stop near the drying phase.
Drying System / Fan Heater Fault
E13
Dishwasher shows E13 and may stop with water inside; sometimes accompanied by unusual noises from the pump area.
Circulation Pump Overload / Blockage
E14
Dishwasher displays E14 and may overfill or underfill; water levels appear incorrect during operation.
Flow Meter / Water Intake Measurement Error
E15
Dishwasher shows E15 and will not start; often associated with the anti-flood system and water in the base.
Persistent Leak / Flood Condition
E16
Dishwasher displays E16 and may not accept new programs; sometimes buttons are unresponsive or behave erratically.
User Interface / Keypad Error
E17
Dishwasher shows E17 and may stop with water inside; sometimes accompanied by unusual humming or no drain at end of cycle.
Drain Sensor / Water Level at End of Cycle Incorrect
E2
Dishwasher fills with water but does not heat; program runs unusually long and E2 is displayed near the end of the cycle.
Heating Circuit Failure
E3
Dishwasher does not drain properly, water remains in the bottom of the tub and E3 is displayed.
Drain Timeout / Pumping Failure
E4
Dishwasher stops mid-cycle, attempts to drain continuously, and E4 is displayed. Sometimes a beeping alarm sounds and the machine will not accept new programs.
Anti-Flood / Overflow Protection Activated
E5
Dishwasher stops with E5 displayed, often early in the cycle, and may have very little or no water inside.
Water Level Sensor / Pressure Switch Error
E6
Dishwasher displays E6 and may not start the wash cycle; sometimes fills and drains but spray arms do not rotate.
Circulation Pump / Wash Motor Failure
E7
Dishwasher shows E7 and may stop mid-cycle; water may be present but not heating correctly or cycle times are erratic.
Temperature Sensor (NTC) Fault
E8
Dishwasher displays E8 and may stop during the wash or rinse phase; sometimes associated with poor wash performance.
Turbidity / Optical Water Sensor Error
E9
Dishwasher shows E9 and may trip the household circuit breaker or stop heating.
Heater Leakage / Earth Fault
Symptom
Dishwasher does not dispense detergent; tablet remains in the dispenser at the end of the cycle.
Detergent Dispenser Door Failure
Symptom
Dishwasher does not fill with enough water; spray arms barely rotate and pump sounds like it is sucking air.
Low Water Level / Underfilling
Symptom
Dishwasher does not release rinse aid; dishes appear dull and water does not sheet off properly.
Rinse Aid Dispenser Fault
Symptom
Dishwasher door drops down quickly or will not stay in a partially open position.
Door Spring / Hinge Cable Failure
Symptom
Dishwasher door is difficult to close or pops open during the cycle.
Door Latch / Alignment Problem
Symptom
Dishwasher emits a burning smell or shows signs of smoke during operation.
Overheating Electrical Component / Wiring Fault
Symptom
Dishwasher has a bad smell, with musty or rotten odours when the door is opened.
Odour / Bacterial Growth in Sump and Hoses
Symptom
Dishwasher interior light (if fitted) does not work, but the machine otherwise operates normally.
Interior Light Failure
Symptom
Dishwasher is very noisy during operation, with grinding, rattling, or loud humming sounds.
Mechanical Noise / Pump or Mounting Fault
Symptom
Dishwasher leaks water from the front of the door during the wash cycle.
Door Seal / Door Alignment Leak
Symptom
Dishwasher leaks water from underneath, with puddles forming under the machine.
Base Leak / Internal Hose or Sump Leak
Symptom
Dishwasher leaves a cloudy film or rainbow sheen on glassware, sometimes with etching.
Detergent / Chemical Damage to Glass
Symptom
Dishwasher leaves standing water in the bottom after the cycle, but no error code is shown.
Partial Drain Failure
Symptom
Dishwasher leaves white, chalky deposits or streaks on glasses and dishes.
Limescale / Poor Rinse Performance
Symptom
Dishwasher overfills with water, with water reaching the door opening or triggering the anti-flood system.
Overfilling / Water Level Control Failure
Symptom
Dishwasher powers on but will not start any program; Start button flashes or beeps and cycle does not begin.
Door Not Recognised as Closed / Door Interlock Fault
Symptom
Dishwasher racks are rusting or the plastic coating is peeling, leaving rust marks on dishes.
Rack Corrosion / Coating Failure
Symptom
Dishwasher runs but dishes come out dirty, with food residues and greasy film remaining on plates and glasses.
Poor Wash Performance / Inadequate Cleaning
Symptom
Dishwasher runs for an excessively long time or appears to be stuck on one part of the cycle.
Program Not Advancing / Sensor Feedback Issue
Symptom
Dishwasher trips the household RCD or circuit breaker intermittently, especially during heating or pump operation.
Intermittent Earth Leakage
Symptom
Dishwasher will not power on at all; no lights or display, no response from any buttons.
No Mains Power / Power Entry Fault
Symptom
Integrated CDA dishwasher door panel is misaligned with adjacent cabinets after installation or service.
Integrated Door Panel Alignment Issue
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E1 |
Dishwasher will not fill with water, cycle stops shortly after start and E1 is displayed on the control panel.
|
Water Inlet Timeout / No Fill Detected | View Details |
| E10 |
Dishwasher displays E10 and may not start or may stop shortly after starting, sometimes with no water entering.
|
Water Inlet Valve Electrical Fault | View Details |
| E11 |
Dishwasher shows E11 and may not complete cycles; sometimes associated with erratic filling or draining behaviour.
|
Main Control Board Communication / Internal Error | View Details |
| E12 |
Dishwasher displays E12 and may have poor drying performance or stop near the drying phase.
|
Drying System / Fan Heater Fault | View Details |
| E13 |
Dishwasher shows E13 and may stop with water inside; sometimes accompanied by unusual noises from the pump area.
|
Circulation Pump Overload / Blockage | View Details |
| E14 |
Dishwasher displays E14 and may overfill or underfill; water levels appear incorrect during operation.
|
Flow Meter / Water Intake Measurement Error | View Details |
| E15 |
Dishwasher shows E15 and will not start; often associated with the anti-flood system and water in the base.
|
Persistent Leak / Flood Condition | View Details |
| E16 |
Dishwasher displays E16 and may not accept new programs; sometimes buttons are unresponsive or behave erratically.
|
User Interface / Keypad Error | View Details |
| E17 |
Dishwasher shows E17 and may stop with water inside; sometimes accompanied by unusual humming or no drain at end of cycle.
|
Drain Sensor / Water Level at End of Cycle Incorrect | View Details |
| E2 |
Dishwasher fills with water but does not heat; program runs unusually long and E2 is displayed near the end of the cycle.
|
Heating Circuit Failure | View Details |
| E3 |
Dishwasher does not drain properly, water remains in the bottom of the tub and E3 is displayed.
|
Drain Timeout / Pumping Failure | View Details |
| E4 |
Dishwasher stops mid-cycle, attempts to drain continuously, and E4 is displayed. Sometimes a beeping alarm sounds and the machine will not accept new programs.
|
Anti-Flood / Overflow Protection Activated | View Details |
| E5 |
Dishwasher stops with E5 displayed, often early in the cycle, and may have very little or no water inside.
|
Water Level Sensor / Pressure Switch Error | View Details |
| E6 |
Dishwasher displays E6 and may not start the wash cycle; sometimes fills and drains but spray arms do not rotate.
|
Circulation Pump / Wash Motor Failure | View Details |
| E7 |
Dishwasher shows E7 and may stop mid-cycle; water may be present but not heating correctly or cycle times are erratic.
|
Temperature Sensor (NTC) Fault | View Details |
| E8 |
Dishwasher displays E8 and may stop during the wash or rinse phase; sometimes associated with poor wash performance.
|
Turbidity / Optical Water Sensor Error | View Details |
| E9 |
Dishwasher shows E9 and may trip the household circuit breaker or stop heating.
|
Heater Leakage / Earth Fault | View Details |
| – |
Dishwasher does not dispense detergent; tablet remains in the dispenser at the end of the cycle.
|
Detergent Dispenser Door Failure | View Details |
| – |
Dishwasher does not fill with enough water; spray arms barely rotate and pump sounds like it is sucking air.
|
Low Water Level / Underfilling | View Details |
| – |
Dishwasher does not release rinse aid; dishes appear dull and water does not sheet off properly.
|
Rinse Aid Dispenser Fault | View Details |
| – |
Dishwasher door drops down quickly or will not stay in a partially open position.
|
Door Spring / Hinge Cable Failure | View Details |
| – |
Dishwasher door is difficult to close or pops open during the cycle.
|
Door Latch / Alignment Problem | View Details |
| – |
Dishwasher emits a burning smell or shows signs of smoke during operation.
|
Overheating Electrical Component / Wiring Fault | View Details |
| – |
Dishwasher has a bad smell, with musty or rotten odours when the door is opened.
|
Odour / Bacterial Growth in Sump and Hoses | View Details |
| – |
Dishwasher interior light (if fitted) does not work, but the machine otherwise operates normally.
|
Interior Light Failure | View Details |
| – |
Dishwasher is very noisy during operation, with grinding, rattling, or loud humming sounds.
|
Mechanical Noise / Pump or Mounting Fault | View Details |
| – |
Dishwasher leaks water from the front of the door during the wash cycle.
|
Door Seal / Door Alignment Leak | View Details |
| – |
Dishwasher leaks water from underneath, with puddles forming under the machine.
|
Base Leak / Internal Hose or Sump Leak | View Details |
| – |
Dishwasher leaves a cloudy film or rainbow sheen on glassware, sometimes with etching.
|
Detergent / Chemical Damage to Glass | View Details |
| – |
Dishwasher leaves standing water in the bottom after the cycle, but no error code is shown.
|
Partial Drain Failure | View Details |
| – |
Dishwasher leaves white, chalky deposits or streaks on glasses and dishes.
|
Limescale / Poor Rinse Performance | View Details |
| – |
Dishwasher overfills with water, with water reaching the door opening or triggering the anti-flood system.
|
Overfilling / Water Level Control Failure | View Details |
| – |
Dishwasher powers on but will not start any program; Start button flashes or beeps and cycle does not begin.
|
Door Not Recognised as Closed / Door Interlock Fault | View Details |
| – |
Dishwasher racks are rusting or the plastic coating is peeling, leaving rust marks on dishes.
|
Rack Corrosion / Coating Failure | View Details |
| – |
Dishwasher runs but dishes come out dirty, with food residues and greasy film remaining on plates and glasses.
|
Poor Wash Performance / Inadequate Cleaning | View Details |
| – |
Dishwasher runs for an excessively long time or appears to be stuck on one part of the cycle.
|
Program Not Advancing / Sensor Feedback Issue | View Details |
| – |
Dishwasher trips the household RCD or circuit breaker intermittently, especially during heating or pump operation.
|
Intermittent Earth Leakage | View Details |
| – |
Dishwasher will not power on at all; no lights or display, no response from any buttons.
|
No Mains Power / Power Entry Fault | View Details |
| – |
Integrated CDA dishwasher door panel is misaligned with adjacent cabinets after installation or service.
|
Integrated Door Panel Alignment Issue | View Details |
No matching codes found
Advertisements