Gorenje Cordless Vacuums Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E1
Cordless vacuum stops shortly after starting and an E1 code flashes on the handle or main body display.
Main Brush Motor Overload / Stall Protection
E2
Cordless vacuum runs for a few seconds, suction is weak, then stops with E2 displayed on the handle or battery indicator panel.
Airflow Restriction / Blocked Filter Protection
E3
Vacuum will not start or shuts down immediately with E3 shown on the LED display or flashing battery icon pattern.
Battery Pack Overheat / Overcurrent Protection
E4
Cordless vacuum does not charge and E4 or a charging error icon appears on the charger base or battery LEDs blink in an error pattern.
Charging Fault / Battery Communication Error
E5
Vacuum stops and displays E5 or a red LED pattern when used on high power, often accompanied by a hot smell from the motor area.
Main Suction Motor Overheat Protection
E6
Cordless vacuum will not start and shows E6 or a general fault icon; sometimes accompanied by no motor sound at all.
Main Control PCB Fault / Internal Electronics Error
E7
LED display shows E7 and the vacuum cannot switch between power modes or responds erratically to the mode button.
User Interface / Keypad Communication Error
E8
Vacuum runs but the motor speed surges up and down, and E8 appears on the display or LEDs flash in a repeating pattern.
Motor Speed Sensor / Feedback Error
E9
Vacuum stops when using the motorized mini turbo brush (pet tool) and E9 is displayed; other tools may work normally.
Accessory Motor Overload / Short Circuit
F1
Battery indicator flashes a specific F1 pattern and the vacuum will not start even though the battery was recently charged.
Battery Pack Undervoltage Lockout
F2
Battery LEDs show an F2 error pattern during charging and the pack does not charge to full capacity.
Battery Temperature Sensor Fault
F3
Vacuum runs only on low power and shows F3 or a restricted power icon; high power mode cannot be selected.
Power Mode Limitation Due to Fault / Protection Mode
F4
Vacuum randomly shuts off and F4 appears briefly on the display; restarting sometimes works for a short time.
Intermittent Power Supply / Connection Fault
F5
Vacuum shows F5 and the LED headlight on the floor nozzle does not work, though suction may be normal.
Accessory Lighting Circuit Fault
Symptom
Battery becomes extremely hot to the touch during normal use or charging.
Abnormal Battery Heating
Symptom
Charging dock LED does not light and the vacuum battery does not charge when docked.
No Charging / Power Supply Failure
Symptom
Dust and debris leak from around the dust container or from joints in the wand during use.
Air Leak / Poor Sealing
Symptom
Dust container door will not latch closed or pops open during use, spilling debris.
Dust Bin Latch Failure
Symptom
Excessive vibration or rattling from the floor nozzle when the brush is running.
Unbalanced Brush Roller / Damaged Bearings
Symptom
Fine dust appears to blow out of the exhaust, causing sneezing or visible haze in the air.
HEPA Filter Bypass or Failure
Symptom
LED headlight on the floor nozzle flickers during use but the brush and suction continue to work.
Intermittent LED Power / Loose Connection
Symptom
Main floor brush does not spin, but suction is present; LED on nozzle may still light.
Brush Roller Drive Failure
Symptom
Mode button or power button is hard to press or sticks, sometimes causing the vacuum to stay on or off unintentionally.
Sticking Control Button / Mechanical Wear
Symptom
Vacuum cannot stand securely on the charging dock or falls off easily.
Docking Alignment / Mechanical Fit Issue
Symptom
Vacuum does not turn on at all; no lights, no sound, even with the battery installed.
No Power / Dead Unit
Symptom
Vacuum emits a burning smell or hot plastic odor during or after use.
Overheating Motor or Electrical Component
Symptom
Vacuum has very weak suction even with a fully charged battery; motor sounds normal but debris is not picked up effectively.
General Suction Loss
Symptom
Vacuum intermittently loses suction when tilting the wand or using above-floor tools.
Intermittent Air Leak or Blockage in Wand / Hose
Symptom
Vacuum is very loud at the exhaust and airflow seems restricted, especially on high power.
Clogged Exhaust / Muffler Path
Symptom
Vacuum leaves visible debris on carpets even after multiple passes; brush is spinning and suction seems normal at the handle.
Ineffective Agitation / Floor Nozzle Performance Issue
Symptom
Vacuum makes a loud high-pitched whine or grinding noise from the motor area during operation.
Motor Bearing Wear / Mechanical Damage
Symptom
Vacuum produces a whistling noise from the handle or dust container area during use.
Minor Air Leak / Misaligned Seal
Symptom
Vacuum runs for only a few minutes on a full charge before shutting off; battery indicator drops quickly.
Reduced Battery Capacity / Battery Aging
Symptom
Vacuum turns on but shuts off after a few seconds without any error code; restarting repeats the same behavior.
Overcurrent or Thermal Protection Without Display Code
Symptom
Vacuum will not stay in handheld or stick configuration; wand or accessories detach easily during use.
Mechanical Latch / Locking Tab Failure
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E1 |
Cordless vacuum stops shortly after starting and an E1 code flashes on the handle or main body display.
|
Main Brush Motor Overload / Stall Protection | View Details |
| E2 |
Cordless vacuum runs for a few seconds, suction is weak, then stops with E2 displayed on the handle or battery indicator panel.
|
Airflow Restriction / Blocked Filter Protection | View Details |
| E3 |
Vacuum will not start or shuts down immediately with E3 shown on the LED display or flashing battery icon pattern.
|
Battery Pack Overheat / Overcurrent Protection | View Details |
| E4 |
Cordless vacuum does not charge and E4 or a charging error icon appears on the charger base or battery LEDs blink in an error pattern.
|
Charging Fault / Battery Communication Error | View Details |
| E5 |
Vacuum stops and displays E5 or a red LED pattern when used on high power, often accompanied by a hot smell from the motor area.
|
Main Suction Motor Overheat Protection | View Details |
| E6 |
Cordless vacuum will not start and shows E6 or a general fault icon; sometimes accompanied by no motor sound at all.
|
Main Control PCB Fault / Internal Electronics Error | View Details |
| E7 |
LED display shows E7 and the vacuum cannot switch between power modes or responds erratically to the mode button.
|
User Interface / Keypad Communication Error | View Details |
| E8 |
Vacuum runs but the motor speed surges up and down, and E8 appears on the display or LEDs flash in a repeating pattern.
|
Motor Speed Sensor / Feedback Error | View Details |
| E9 |
Vacuum stops when using the motorized mini turbo brush (pet tool) and E9 is displayed; other tools may work normally.
|
Accessory Motor Overload / Short Circuit | View Details |
| F1 |
Battery indicator flashes a specific F1 pattern and the vacuum will not start even though the battery was recently charged.
|
Battery Pack Undervoltage Lockout | View Details |
| F2 |
Battery LEDs show an F2 error pattern during charging and the pack does not charge to full capacity.
|
Battery Temperature Sensor Fault | View Details |
| F3 |
Vacuum runs only on low power and shows F3 or a restricted power icon; high power mode cannot be selected.
|
Power Mode Limitation Due to Fault / Protection Mode | View Details |
| F4 |
Vacuum randomly shuts off and F4 appears briefly on the display; restarting sometimes works for a short time.
|
Intermittent Power Supply / Connection Fault | View Details |
| F5 |
Vacuum shows F5 and the LED headlight on the floor nozzle does not work, though suction may be normal.
|
Accessory Lighting Circuit Fault | View Details |
| – |
Battery becomes extremely hot to the touch during normal use or charging.
|
Abnormal Battery Heating | View Details |
| – |
Charging dock LED does not light and the vacuum battery does not charge when docked.
|
No Charging / Power Supply Failure | View Details |
| – |
Dust and debris leak from around the dust container or from joints in the wand during use.
|
Air Leak / Poor Sealing | View Details |
| – |
Dust container door will not latch closed or pops open during use, spilling debris.
|
Dust Bin Latch Failure | View Details |
| – |
Excessive vibration or rattling from the floor nozzle when the brush is running.
|
Unbalanced Brush Roller / Damaged Bearings | View Details |
| – |
Fine dust appears to blow out of the exhaust, causing sneezing or visible haze in the air.
|
HEPA Filter Bypass or Failure | View Details |
| – |
LED headlight on the floor nozzle flickers during use but the brush and suction continue to work.
|
Intermittent LED Power / Loose Connection | View Details |
| – |
Main floor brush does not spin, but suction is present; LED on nozzle may still light.
|
Brush Roller Drive Failure | View Details |
| – |
Mode button or power button is hard to press or sticks, sometimes causing the vacuum to stay on or off unintentionally.
|
Sticking Control Button / Mechanical Wear | View Details |
| – |
Vacuum cannot stand securely on the charging dock or falls off easily.
|
Docking Alignment / Mechanical Fit Issue | View Details |
| – |
Vacuum does not turn on at all; no lights, no sound, even with the battery installed.
|
No Power / Dead Unit | View Details |
| – |
Vacuum emits a burning smell or hot plastic odor during or after use.
|
Overheating Motor or Electrical Component | View Details |
| – |
Vacuum has very weak suction even with a fully charged battery; motor sounds normal but debris is not picked up effectively.
|
General Suction Loss | View Details |
| – |
Vacuum intermittently loses suction when tilting the wand or using above-floor tools.
|
Intermittent Air Leak or Blockage in Wand / Hose | View Details |
| – |
Vacuum is very loud at the exhaust and airflow seems restricted, especially on high power.
|
Clogged Exhaust / Muffler Path | View Details |
| – |
Vacuum leaves visible debris on carpets even after multiple passes; brush is spinning and suction seems normal at the handle.
|
Ineffective Agitation / Floor Nozzle Performance Issue | View Details |
| – |
Vacuum makes a loud high-pitched whine or grinding noise from the motor area during operation.
|
Motor Bearing Wear / Mechanical Damage | View Details |
| – |
Vacuum produces a whistling noise from the handle or dust container area during use.
|
Minor Air Leak / Misaligned Seal | View Details |
| – |
Vacuum runs for only a few minutes on a full charge before shutting off; battery indicator drops quickly.
|
Reduced Battery Capacity / Battery Aging | View Details |
| – |
Vacuum turns on but shuts off after a few seconds without any error code; restarting repeats the same behavior.
|
Overcurrent or Thermal Protection Without Display Code | View Details |
| – |
Vacuum will not stay in handheld or stick configuration; wand or accessories detach easily during use.
|
Mechanical Latch / Locking Tab Failure | View Details |
No matching codes found
Advertisements