Panasonic Cordless Vacuums Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E01
Vacuum will not power on; battery LEDs flash briefly then turn off
Battery Pack Protection Trip / Undervoltage Lockout
E02
Vacuum stops shortly after starting; motor cuts out within a few seconds and error E02 appears
Overcurrent / Motor Overload Protection
E03
Vacuum runs but suction is very weak; E03 or a filter icon appears on the display
Airflow Restriction / Filter Clogged Detection
E04
Brush bar stops spinning; E04 or a brush icon flashes on the handle display
Brush Roll Jam / Motorized Nozzle Overload
E05
Vacuum shuts down after a short run time; body feels hot and E05 or a thermometer icon appears
Thermal Overload / Overheating Protection
E06
Vacuum does not recognize the battery; E06 displayed and battery icon blinks
Battery Communication Error
E07
Vacuum will not charge; charger LED blinks and E07 appears on the vacuum display
Charging Fault / Charger-Battery Mismatch
E08
Vacuum powers on but motor does not spin; E08 displayed or motor icon flashes
Motor Drive Circuit Fault
E09
LED display shows E09 and vacuum shuts down when switching to high power mode
High-Load Overcurrent in Turbo Mode
E10
Vacuum display shows E10 and unit will not start; some LEDs may blink in sequence
Internal Communication Error (Handle PCB to Main PCB)
E11
Vacuum shows E11 and suction pulses or surges during operation
Pressure Sensor / Dust Sensor Fault
E12
Vacuum indicates E12 and cannot switch between modes; mode button unresponsive
Keypad / Button Input Error
E13
Vacuum shows E13 and runs only at low power regardless of setting
Power Mode Control Fault / Current Limiting
E14
Vacuum displays E14 and battery indicator flashes rapidly; unit shuts off immediately
Battery Overtemperature / NTC Sensor Fault
E15
Vacuum shows E15 and cannot detect or power the motorized floor nozzle
Nozzle Communication / Power Supply Error
Symptom
Accessory tools (crevice, upholstery) have very weak suction compared to floor nozzle
Tool Port Restriction or Leak
Symptom
Dust cup door will not latch closed or pops open during use
Dust Cup Latch Failure
Symptom
LED lights on the floor nozzle do not turn on, but the brush still spins
Nozzle LED Circuit Failure
Symptom
Vacuum cannot stand upright in parking position or collapses easily
Mechanical Lock / Hinge Wear
Symptom
Vacuum charges extremely slowly or never reaches full charge, but no error code is shown
Degraded Charging Performance
Symptom
Vacuum continues to run for a few seconds after power button is released
Power Latch / Control Logic Delay
Symptom
Vacuum does not respond to mode changes; stuck in eco or turbo mode
Mode Selector Failure
Symptom
Vacuum emits a burning smell during or after use
Overheating Motor or Nozzle Brush
Symptom
Vacuum handle or body becomes uncomfortably hot to touch during normal use
Excessive Heat Build-Up
Symptom
Vacuum has power but suction is weak even with clean filters and empty bin
Air Leakage / Loss of Sealing
Symptom
Vacuum is very loud with rattling or grinding noises from the main body
Mechanical Damage to Motor or Fan
Symptom
Vacuum leaves debris on carpet; brush spins but pickup is poor
Ineffective Agitation / Worn Brush Bristles
Symptom
Vacuum leaves fine dust on hard floors even after multiple passes
Hard Floor Tool Inefficiency / Airflow Bypass
Symptom
Vacuum makes a loud high-pitched whine during operation
Motor Bearing Wear / Air Leak Whistle
Symptom
Vacuum produces an unusual musty or dusty odor during use
Contaminated Filters and Dust Path
Symptom
Vacuum randomly resets or the display flickers during use
Power Supply Instability
Symptom
Vacuum runs for only a few minutes on a full charge, then stops without an error code
Severely Reduced Battery Capacity
Symptom
Vacuum shuts off intermittently when moving the wand or nozzle
Intermittent Electrical Connection
Symptom
Vacuum vibrates excessively in the hand or at the nozzle during use
Imbalanced Brush Roll or Motor Fan
Symptom
Vacuum will not turn on at all; no lights, no sound
Complete Power Loss
Symptom
Vacuum's dust sensor indicator (if equipped) never changes, always showing clean or always dirty
Dust Sensor Malfunction
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E01 |
Vacuum will not power on; battery LEDs flash briefly then turn off
|
Battery Pack Protection Trip / Undervoltage Lockout | View Details |
| E02 |
Vacuum stops shortly after starting; motor cuts out within a few seconds and error E02 appears
|
Overcurrent / Motor Overload Protection | View Details |
| E03 |
Vacuum runs but suction is very weak; E03 or a filter icon appears on the display
|
Airflow Restriction / Filter Clogged Detection | View Details |
| E04 |
Brush bar stops spinning; E04 or a brush icon flashes on the handle display
|
Brush Roll Jam / Motorized Nozzle Overload | View Details |
| E05 |
Vacuum shuts down after a short run time; body feels hot and E05 or a thermometer icon appears
|
Thermal Overload / Overheating Protection | View Details |
| E06 |
Vacuum does not recognize the battery; E06 displayed and battery icon blinks
|
Battery Communication Error | View Details |
| E07 |
Vacuum will not charge; charger LED blinks and E07 appears on the vacuum display
|
Charging Fault / Charger-Battery Mismatch | View Details |
| E08 |
Vacuum powers on but motor does not spin; E08 displayed or motor icon flashes
|
Motor Drive Circuit Fault | View Details |
| E09 |
LED display shows E09 and vacuum shuts down when switching to high power mode
|
High-Load Overcurrent in Turbo Mode | View Details |
| E10 |
Vacuum display shows E10 and unit will not start; some LEDs may blink in sequence
|
Internal Communication Error (Handle PCB to Main PCB) | View Details |
| E11 |
Vacuum shows E11 and suction pulses or surges during operation
|
Pressure Sensor / Dust Sensor Fault | View Details |
| E12 |
Vacuum indicates E12 and cannot switch between modes; mode button unresponsive
|
Keypad / Button Input Error | View Details |
| E13 |
Vacuum shows E13 and runs only at low power regardless of setting
|
Power Mode Control Fault / Current Limiting | View Details |
| E14 |
Vacuum displays E14 and battery indicator flashes rapidly; unit shuts off immediately
|
Battery Overtemperature / NTC Sensor Fault | View Details |
| E15 |
Vacuum shows E15 and cannot detect or power the motorized floor nozzle
|
Nozzle Communication / Power Supply Error | View Details |
| – |
Accessory tools (crevice, upholstery) have very weak suction compared to floor nozzle
|
Tool Port Restriction or Leak | View Details |
| – |
Dust cup door will not latch closed or pops open during use
|
Dust Cup Latch Failure | View Details |
| – |
LED lights on the floor nozzle do not turn on, but the brush still spins
|
Nozzle LED Circuit Failure | View Details |
| – |
Vacuum cannot stand upright in parking position or collapses easily
|
Mechanical Lock / Hinge Wear | View Details |
| – |
Vacuum charges extremely slowly or never reaches full charge, but no error code is shown
|
Degraded Charging Performance | View Details |
| – |
Vacuum continues to run for a few seconds after power button is released
|
Power Latch / Control Logic Delay | View Details |
| – |
Vacuum does not respond to mode changes; stuck in eco or turbo mode
|
Mode Selector Failure | View Details |
| – |
Vacuum emits a burning smell during or after use
|
Overheating Motor or Nozzle Brush | View Details |
| – |
Vacuum handle or body becomes uncomfortably hot to touch during normal use
|
Excessive Heat Build-Up | View Details |
| – |
Vacuum has power but suction is weak even with clean filters and empty bin
|
Air Leakage / Loss of Sealing | View Details |
| – |
Vacuum is very loud with rattling or grinding noises from the main body
|
Mechanical Damage to Motor or Fan | View Details |
| – |
Vacuum leaves debris on carpet; brush spins but pickup is poor
|
Ineffective Agitation / Worn Brush Bristles | View Details |
| – |
Vacuum leaves fine dust on hard floors even after multiple passes
|
Hard Floor Tool Inefficiency / Airflow Bypass | View Details |
| – |
Vacuum makes a loud high-pitched whine during operation
|
Motor Bearing Wear / Air Leak Whistle | View Details |
| – |
Vacuum produces an unusual musty or dusty odor during use
|
Contaminated Filters and Dust Path | View Details |
| – |
Vacuum randomly resets or the display flickers during use
|
Power Supply Instability | View Details |
| – |
Vacuum runs for only a few minutes on a full charge, then stops without an error code
|
Severely Reduced Battery Capacity | View Details |
| – |
Vacuum shuts off intermittently when moving the wand or nozzle
|
Intermittent Electrical Connection | View Details |
| – |
Vacuum vibrates excessively in the hand or at the nozzle during use
|
Imbalanced Brush Roll or Motor Fan | View Details |
| – |
Vacuum will not turn on at all; no lights, no sound
|
Complete Power Loss | View Details |
| – |
Vacuum's dust sensor indicator (if equipped) never changes, always showing clean or always dirty
|
Dust Sensor Malfunction | View Details |
No matching codes found
Advertisements