SMEG Ice Makers Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E01
Ice maker will not power on, display is dark, unit appears completely dead.
Main Power Supply or Control Board Failure
E02
Ice maker powers on but does not start ice production; compressor does not run.
Compressor Start Circuit or Relay Failure
E03
Ice maker runs but does not produce any ice; evaporator plate does not frost.
Refrigeration System or Evaporator Thermistor Fault
E04
Ice maker stops mid-cycle and displays an over-temperature or high temperature alarm.
Cabinet Temperature Too High / Sensor Error
E05
Ice maker displays a water supply error and stops ice production.
Water Inlet Failure / Low Water Pressure
E06
Ice maker shows a drain error; water remains in the sump or bin and unit stops.
Drain Pump or Drain Line Obstruction
E07
Ice maker indicates a bin full or ice level sensor error even when the bin is empty.
Ice Level Sensor or Bin Switch Fault
E08
Ice maker displays a fan error; internal fan does not run and ice production is poor or stops.
Evaporator or Condenser Fan Motor Failure
E09
Ice maker shows a sensor error; unit may stop or run erratically.
General Temperature Sensor / NTC Fault
E10
Ice maker indicates a defrost or de-icing error; evaporator plate remains iced over.
Defrost Heater or Defrost Control Failure
E11
Ice maker displays a pump error; circulation pump does not run and ice formation is irregular.
Water Circulation Pump Failure
E12
Ice maker shows a communication error between display and main control board.
Communication Bus Failure
E13
Ice maker indicates a door or bin open error even when closed.
Door Switch or Bin Switch Failure
E14
Ice maker displays a high pressure or condenser overheat error; compressor may shut down.
Condenser Overheating / High Pressure Protection
E15
Ice maker shows a low ambient temperature error; unit suspends ice production.
Ambient Temperature Out of Range
E16
Ice maker displays a water leak or overflow error; internal safety float may be triggered.
Internal Leak Detection / Overflow
E17
Ice maker shows a descaling or cleaning error; cleaning cycle cannot complete.
Cleaning Cycle Failure / Scale Sensor Error
E18
Ice maker displays a low voltage or power supply error; unit may reset intermittently.
Input Power Instability / Low Voltage Detection
Symptom
Buttons on the ice maker control panel do not respond or respond intermittently.
Keypad or Touch Control Failure
Symptom
Ice cubes are cloudy or white instead of clear.
High Mineral Content or Aerated Water
Symptom
Ice cubes have a bad taste or odor.
Contaminated Water Path or Storage Bin
Symptom
Ice maker cycles on and off frequently without producing much ice.
Short Cycling Due to Sensor or Control Issues
Symptom
Ice maker display is blank but internal components (fans/compressor) still run.
User Interface Power or Communication Failure
Symptom
Ice maker emits a burning smell or shows signs of overheating.
Overheating Electrical Component
Symptom
Ice maker forms ice on the evaporator plate but does not release it into the bin.
Harvest Cycle Failure
Symptom
Ice maker interior is warm and ice melts quickly in the bin.
Poor Insulation or Cooling in Storage Bin
Symptom
Ice maker interior surfaces show heavy frost or ice buildup.
Excessive Frost / Moisture Ingress
Symptom
Ice maker is leaking water inside the bin, causing ice to clump together.
Internal Drip or Overflow into Ice Bin
Symptom
Ice maker is leaking water onto the floor from underneath.
External Water Leak
Symptom
Ice maker is making no ice at all, but the display is on and fans run.
No Ice Production with Apparent Normal Operation
Symptom
Ice maker is very noisy during operation (grinding, rattling, or buzzing).
Mechanical Noise from Fans, Compressor, or Pump
Symptom
Ice maker produces hollow ice cubes that break easily.
Over-Harvest or Incomplete Freeze
Symptom
Ice maker produces ice but the cubes are irregularly shaped or fused together on the plate.
Water Distribution or Freeze Pattern Issue
Symptom
Ice maker produces ice very slowly compared to normal.
Reduced Ice Production Capacity
Symptom
Ice maker runs but produces very small or thin ice cubes.
Insufficient Water Fill or Short Freeze Cycle
Symptom
Ice maker runs continuously and does not stop even when the bin is full.
Ice Level Detection Failure
Symptom
Ice maker trips the household circuit breaker when it starts.
Electrical Short or Overcurrent on Startup
Symptom
Ice maker will not start at all, but the display lights up and responds.
Start Inhibit Due to Safety or Mode Setting
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E01 |
Ice maker will not power on, display is dark, unit appears completely dead.
|
Main Power Supply or Control Board Failure | View Details |
| E02 |
Ice maker powers on but does not start ice production; compressor does not run.
|
Compressor Start Circuit or Relay Failure | View Details |
| E03 |
Ice maker runs but does not produce any ice; evaporator plate does not frost.
|
Refrigeration System or Evaporator Thermistor Fault | View Details |
| E04 |
Ice maker stops mid-cycle and displays an over-temperature or high temperature alarm.
|
Cabinet Temperature Too High / Sensor Error | View Details |
| E05 |
Ice maker displays a water supply error and stops ice production.
|
Water Inlet Failure / Low Water Pressure | View Details |
| E06 |
Ice maker shows a drain error; water remains in the sump or bin and unit stops.
|
Drain Pump or Drain Line Obstruction | View Details |
| E07 |
Ice maker indicates a bin full or ice level sensor error even when the bin is empty.
|
Ice Level Sensor or Bin Switch Fault | View Details |
| E08 |
Ice maker displays a fan error; internal fan does not run and ice production is poor or stops.
|
Evaporator or Condenser Fan Motor Failure | View Details |
| E09 |
Ice maker shows a sensor error; unit may stop or run erratically.
|
General Temperature Sensor / NTC Fault | View Details |
| E10 |
Ice maker indicates a defrost or de-icing error; evaporator plate remains iced over.
|
Defrost Heater or Defrost Control Failure | View Details |
| E11 |
Ice maker displays a pump error; circulation pump does not run and ice formation is irregular.
|
Water Circulation Pump Failure | View Details |
| E12 |
Ice maker shows a communication error between display and main control board.
|
Communication Bus Failure | View Details |
| E13 |
Ice maker indicates a door or bin open error even when closed.
|
Door Switch or Bin Switch Failure | View Details |
| E14 |
Ice maker displays a high pressure or condenser overheat error; compressor may shut down.
|
Condenser Overheating / High Pressure Protection | View Details |
| E15 |
Ice maker shows a low ambient temperature error; unit suspends ice production.
|
Ambient Temperature Out of Range | View Details |
| E16 |
Ice maker displays a water leak or overflow error; internal safety float may be triggered.
|
Internal Leak Detection / Overflow | View Details |
| E17 |
Ice maker shows a descaling or cleaning error; cleaning cycle cannot complete.
|
Cleaning Cycle Failure / Scale Sensor Error | View Details |
| E18 |
Ice maker displays a low voltage or power supply error; unit may reset intermittently.
|
Input Power Instability / Low Voltage Detection | View Details |
| – |
Buttons on the ice maker control panel do not respond or respond intermittently.
|
Keypad or Touch Control Failure | View Details |
| – |
Ice cubes are cloudy or white instead of clear.
|
High Mineral Content or Aerated Water | View Details |
| – |
Ice cubes have a bad taste or odor.
|
Contaminated Water Path or Storage Bin | View Details |
| – |
Ice maker cycles on and off frequently without producing much ice.
|
Short Cycling Due to Sensor or Control Issues | View Details |
| – |
Ice maker display is blank but internal components (fans/compressor) still run.
|
User Interface Power or Communication Failure | View Details |
| – |
Ice maker emits a burning smell or shows signs of overheating.
|
Overheating Electrical Component | View Details |
| – |
Ice maker forms ice on the evaporator plate but does not release it into the bin.
|
Harvest Cycle Failure | View Details |
| – |
Ice maker interior is warm and ice melts quickly in the bin.
|
Poor Insulation or Cooling in Storage Bin | View Details |
| – |
Ice maker interior surfaces show heavy frost or ice buildup.
|
Excessive Frost / Moisture Ingress | View Details |
| – |
Ice maker is leaking water inside the bin, causing ice to clump together.
|
Internal Drip or Overflow into Ice Bin | View Details |
| – |
Ice maker is leaking water onto the floor from underneath.
|
External Water Leak | View Details |
| – |
Ice maker is making no ice at all, but the display is on and fans run.
|
No Ice Production with Apparent Normal Operation | View Details |
| – |
Ice maker is very noisy during operation (grinding, rattling, or buzzing).
|
Mechanical Noise from Fans, Compressor, or Pump | View Details |
| – |
Ice maker produces hollow ice cubes that break easily.
|
Over-Harvest or Incomplete Freeze | View Details |
| – |
Ice maker produces ice but the cubes are irregularly shaped or fused together on the plate.
|
Water Distribution or Freeze Pattern Issue | View Details |
| – |
Ice maker produces ice very slowly compared to normal.
|
Reduced Ice Production Capacity | View Details |
| – |
Ice maker runs but produces very small or thin ice cubes.
|
Insufficient Water Fill or Short Freeze Cycle | View Details |
| – |
Ice maker runs continuously and does not stop even when the bin is full.
|
Ice Level Detection Failure | View Details |
| – |
Ice maker trips the household circuit breaker when it starts.
|
Electrical Short or Overcurrent on Startup | View Details |
| – |
Ice maker will not start at all, but the display lights up and responds.
|
Start Inhibit Due to Safety or Mode Setting | View Details |
No matching codes found
Advertisements