Hisense Multicookers Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
C1
C1 or similar calibration code appears and the cooker refuses to start.
Sensor Calibration Error
E0
Multicooker does not start a cooking program and displays E0 immediately after pressing Start.
Lid Not Detected / Lid Switch Open
E1
Multicooker beeps and shows E1 shortly after starting a program; heating does not begin.
Open or Shorted Main Temperature Sensor (NTC)
E2
Display shows E2 and the cooker stops heating during a program, often after preheating.
Overtemperature Protection / Sensor Overrange
E3
E3 appears during pressure cooking; unit stops and may release steam prematurely.
Pressure Sensor Fault / Pressure Overrange
E4
E4 error appears and the cooker refuses to enter pressure mode or stops shortly after building pressure.
Pressure Not Reached / Pressure Leakage Detected
E5
E5 is displayed and the cooker stops heating; often associated with power-on or early in a cycle.
Heating Circuit Fault / Heater Open or Short
E6
E6 appears on the display and the cooker will not start any program.
Main Control Board Communication / Internal Fault
E7
E7 error appears intermittently, often when using high-temperature frying or sauté modes.
Upper Lid Temperature Sensor Fault
E8
E8 is displayed and the cooker stops; often associated with unstable or low mains voltage.
Input Voltage Out of Range
E9
E9 appears and the cooker will not start; sometimes accompanied by a faint burning smell previously.
Short Circuit / Overcurrent Protection Triggered
Err
Display shows a generic 'Err' message and beeps; no specific code number is shown.
Generic System Error / Self-Test Failure
F1
F1 error appears at power-on; no cooking functions are available.
Keypad / Touch Panel Fault
F2
F2 error appears during operation; cooker may stop unexpectedly.
Secondary Temperature Sensor Fault (Auxiliary NTC)
F3
F3 appears and the cooker will not heat; often associated with sensor wiring issues.
Sensor Circuit Short / Crossed Wires
F4
F4 error appears when trying to start high-power modes like frying or pressure cooking.
Heater Drive Feedback Fault
H0
Display shows H0 and the cooker remains in a warm state without starting full heating.
Keep-Warm Only Mode / Heater Drive Limitation
H1
H1 appears and the cooker stops heating; often after extended use or blocked vents.
High Internal Temperature / Overheat Protection
LID
Display shows 'LID' or a lid icon and the cooker refuses to start pressure or cooking programs.
Lid Not Locked / Lock Sensor Fault
P0
Display shows P0 and the cooker does not build pressure or heat normally.
Pressure Program Not Properly Selected / Low Pressure Mode
P1
Display shows P1 and the cooker stops mid-cycle, often during pressure cooking.
Abnormal Pressure Rise / Safety Cutoff
U8
U8 or similar under-voltage code appears and the cooker cancels the program.
Under-Voltage Protection
Symptom
Buttons or touch keys respond intermittently or activate the wrong function.
Keypad / Touch Panel Misoperation
Symptom
Display and lights flicker or reset when the heater turns on.
Voltage Drop / Internal Power Instability
Symptom
Display segments are missing or unreadable; some numbers or icons do not light.
Display Module Fault
Symptom
Float valve does not rise during pressure cooking; cooker times out or shows pressure-related errors.
Float Valve Stuck / Not Sealing
Symptom
Inner pot coating is peeling or scratched; food sticks badly and may show dark flakes.
Non-Stick Coating Degradation
Symptom
Keep Warm mode overheats food, causing it to dry out or burn on the bottom.
Keep-Warm Temperature Too High
Symptom
Loud clicking, popping, or metallic noises during heating or pressure cooking.
Thermal Expansion Noise / Mechanical Stress
Symptom
Multicooker does not power on at all; no lights or display when plugged in.
No Power / Dead Appliance
Symptom
Multicooker heats very slowly or never reaches cooking temperature; food remains undercooked.
Reduced Heating Output
Symptom
Multicooker lid is difficult to open after cooking; feels stuck even after pressure release.
Lid Mechanism Binding
Symptom
Multicooker makes a constant beeping sound and will not start cooking.
Alarm Condition / Safety Interlock Active
Symptom
Multicooker overheats and burns food on the bottom while the top remains undercooked.
Temperature Regulation Inaccuracy
Symptom
Multicooker powers on but will not start any program; pressing Start has no effect.
Start Circuit / Control Logic Failure
Symptom
Multicooker switches to Keep Warm too early; rice or food is undercooked.
Premature Cooking Cycle Termination
Symptom
Steam continuously escapes from the steam release valve during pressure cooking; pressure never builds.
Steam Release Valve Not Sealing
Symptom
Steam or water leaks from around the lid during pressure cooking; cooker struggles to reach pressure.
Lid Seal Leakage
Symptom
Timer or clock runs too fast or too slow; cooking times are inaccurate.
Timing Circuit Inaccuracy
Symptom
Unusual burning smell or smoke from the multicooker during use.
Overheating / Electrical Insulation Breakdown
Symptom
Water or starchy liquid drips from the sides or bottom of the multicooker during or after cooking.
External Leakage / Condensation Management Failure
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| C1 |
C1 or similar calibration code appears and the cooker refuses to start.
|
Sensor Calibration Error | View Details |
| E0 |
Multicooker does not start a cooking program and displays E0 immediately after pressing Start.
|
Lid Not Detected / Lid Switch Open | View Details |
| E1 |
Multicooker beeps and shows E1 shortly after starting a program; heating does not begin.
|
Open or Shorted Main Temperature Sensor (NTC) | View Details |
| E2 |
Display shows E2 and the cooker stops heating during a program, often after preheating.
|
Overtemperature Protection / Sensor Overrange | View Details |
| E3 |
E3 appears during pressure cooking; unit stops and may release steam prematurely.
|
Pressure Sensor Fault / Pressure Overrange | View Details |
| E4 |
E4 error appears and the cooker refuses to enter pressure mode or stops shortly after building pressure.
|
Pressure Not Reached / Pressure Leakage Detected | View Details |
| E5 |
E5 is displayed and the cooker stops heating; often associated with power-on or early in a cycle.
|
Heating Circuit Fault / Heater Open or Short | View Details |
| E6 |
E6 appears on the display and the cooker will not start any program.
|
Main Control Board Communication / Internal Fault | View Details |
| E7 |
E7 error appears intermittently, often when using high-temperature frying or sauté modes.
|
Upper Lid Temperature Sensor Fault | View Details |
| E8 |
E8 is displayed and the cooker stops; often associated with unstable or low mains voltage.
|
Input Voltage Out of Range | View Details |
| E9 |
E9 appears and the cooker will not start; sometimes accompanied by a faint burning smell previously.
|
Short Circuit / Overcurrent Protection Triggered | View Details |
| Err |
Display shows a generic 'Err' message and beeps; no specific code number is shown.
|
Generic System Error / Self-Test Failure | View Details |
| F1 |
F1 error appears at power-on; no cooking functions are available.
|
Keypad / Touch Panel Fault | View Details |
| F2 |
F2 error appears during operation; cooker may stop unexpectedly.
|
Secondary Temperature Sensor Fault (Auxiliary NTC) | View Details |
| F3 |
F3 appears and the cooker will not heat; often associated with sensor wiring issues.
|
Sensor Circuit Short / Crossed Wires | View Details |
| F4 |
F4 error appears when trying to start high-power modes like frying or pressure cooking.
|
Heater Drive Feedback Fault | View Details |
| H0 |
Display shows H0 and the cooker remains in a warm state without starting full heating.
|
Keep-Warm Only Mode / Heater Drive Limitation | View Details |
| H1 |
H1 appears and the cooker stops heating; often after extended use or blocked vents.
|
High Internal Temperature / Overheat Protection | View Details |
| LID |
Display shows 'LID' or a lid icon and the cooker refuses to start pressure or cooking programs.
|
Lid Not Locked / Lock Sensor Fault | View Details |
| P0 |
Display shows P0 and the cooker does not build pressure or heat normally.
|
Pressure Program Not Properly Selected / Low Pressure Mode | View Details |
| P1 |
Display shows P1 and the cooker stops mid-cycle, often during pressure cooking.
|
Abnormal Pressure Rise / Safety Cutoff | View Details |
| U8 |
U8 or similar under-voltage code appears and the cooker cancels the program.
|
Under-Voltage Protection | View Details |
| – |
Buttons or touch keys respond intermittently or activate the wrong function.
|
Keypad / Touch Panel Misoperation | View Details |
| – |
Display and lights flicker or reset when the heater turns on.
|
Voltage Drop / Internal Power Instability | View Details |
| – |
Display segments are missing or unreadable; some numbers or icons do not light.
|
Display Module Fault | View Details |
| – |
Float valve does not rise during pressure cooking; cooker times out or shows pressure-related errors.
|
Float Valve Stuck / Not Sealing | View Details |
| – |
Inner pot coating is peeling or scratched; food sticks badly and may show dark flakes.
|
Non-Stick Coating Degradation | View Details |
| – |
Keep Warm mode overheats food, causing it to dry out or burn on the bottom.
|
Keep-Warm Temperature Too High | View Details |
| – |
Loud clicking, popping, or metallic noises during heating or pressure cooking.
|
Thermal Expansion Noise / Mechanical Stress | View Details |
| – |
Multicooker does not power on at all; no lights or display when plugged in.
|
No Power / Dead Appliance | View Details |
| – |
Multicooker heats very slowly or never reaches cooking temperature; food remains undercooked.
|
Reduced Heating Output | View Details |
| – |
Multicooker lid is difficult to open after cooking; feels stuck even after pressure release.
|
Lid Mechanism Binding | View Details |
| – |
Multicooker makes a constant beeping sound and will not start cooking.
|
Alarm Condition / Safety Interlock Active | View Details |
| – |
Multicooker overheats and burns food on the bottom while the top remains undercooked.
|
Temperature Regulation Inaccuracy | View Details |
| – |
Multicooker powers on but will not start any program; pressing Start has no effect.
|
Start Circuit / Control Logic Failure | View Details |
| – |
Multicooker switches to Keep Warm too early; rice or food is undercooked.
|
Premature Cooking Cycle Termination | View Details |
| – |
Steam continuously escapes from the steam release valve during pressure cooking; pressure never builds.
|
Steam Release Valve Not Sealing | View Details |
| – |
Steam or water leaks from around the lid during pressure cooking; cooker struggles to reach pressure.
|
Lid Seal Leakage | View Details |
| – |
Timer or clock runs too fast or too slow; cooking times are inaccurate.
|
Timing Circuit Inaccuracy | View Details |
| – |
Unusual burning smell or smoke from the multicooker during use.
|
Overheating / Electrical Insulation Breakdown | View Details |
| – |
Water or starchy liquid drips from the sides or bottom of the multicooker during or after cooking.
|
External Leakage / Condensation Management Failure | View Details |
No matching codes found
Advertisements