ProfiCook
ProfiCook Ice Makers Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E1
Ice maker stops shortly after startup and displays E1 on the control panel.
Water Inlet Fault / Low Water Level Detection Error
E10
E10 appears and the machine stops; water may remain in the reservoir and no ice is produced.
Drain / Overflow Protection Error
E2
ProfiCook ice maker beeps and shows E2; unit powers on but does not start ice production.
Ice Full Sensor / Infrared Beam Obstruction
E3
Display shows E3 and the machine stops mid-cycle; compressor may not run or runs briefly.
Temperature Sensor (NTC) Fault on Evaporator
E4
E4 appears on the display; ice production stops and the fan may continue to run.
Refrigeration System Protection / Overheat or Overcool Error
E5
E5 error on display; machine powers on but does not harvest ice properly.
Ice Tray / Evaporator Position or Motor Fault
E6
E6 displayed; unit may start but stops with beeping before completing a cycle.
Water Pump Fault / Circulation Failure
E7
E7 appears on the display; unit may run but produces very little or no ice.
Ambient Temperature Sensor Fault
E8
E8 error code; machine may start but shuts down with beeping and no ice is produced.
Compressor Start / Overcurrent Protection Error
E9
E9 displayed; unit powers on but internal fan does not run and ice production is poor or absent.
Evaporator / Internal Fan Motor Fault
Symptom
Buttons on the control panel respond intermittently or require very hard presses.
Keypad Wear / Poor Contact
Symptom
Display is lit but segments are missing or unreadable.
Display Module / LED Segment Failure
Symptom
Grinding or scraping noise during ice harvest cycle.
Ice Tray Drive Mechanism Wear or Obstruction
Symptom
Ice cubes have a bad taste or odor.
Water Contamination / Internal Biofilm or Scale
Symptom
Ice cubes stick together in large clumps in the storage bin.
Ice Clumping / Overproduction Without Use
Symptom
Ice maker continuously runs and does not stop even when the bin is full.
Ice-Full Sensor Not Detecting
Symptom
Ice maker does not power on at all; no lights or display when plugged in.
No Power / Main Power Supply Failure
Symptom
Ice maker exterior becomes unusually hot to the touch during operation.
Overheating Cabinet / Poor Heat Rejection
Symptom
Ice maker interior surfaces sweat excessively, with condensation dripping into the bin.
Condensation Management Issue
Symptom
Ice maker is running but ice production is very slow compared to normal.
Reduced Cooling Efficiency
Symptom
Ice maker overflows water into the ice bin or out of the top.
Water Level Control Failure
Symptom
Ice maker produces hollow or thin-walled ice cubes.
Water Flow Imbalance / Short Fill Time
Symptom
Ice maker produces ice only for a short time, then stops until manually restarted.
Intermittent Control or Sensor Fault
Symptom
Ice maker produces ice, but cubes are very small and melt quickly.
Insufficient Cooling Capacity / Short Freeze Cycle
Symptom
Ice maker runs but makes a loud rattling or vibrating noise.
Mechanical Vibration / Loose Component
Symptom
Ice maker runs but produces no ice at all; evaporator plate does not get cold.
Refrigerant System Failure / No Cooling
Symptom
Ice maker runs but water does not flow over the evaporator or into the ice tray.
Water Circulation Failure
Symptom
Ice maker stops producing ice even though the bin is not full and no error code is shown.
False Ice-Full Detection
Symptom
Loud buzzing or humming noise from the rear of the unit, even when no ice is being produced.
Compressor or Fan Motor Noise
Symptom
Unit emits a plastic or burning smell during operation.
Overheating Component or Electrical Insulation Odor
Symptom
Unit frequently shuts off mid-cycle without any error code.
Thermal Overload / Power Interruption
Symptom
Unit powers on but does not start ice production when the START button is pressed.
User Interface / Control Panel Input Failure
Symptom
Unit trips the household circuit breaker or RCD when turned on.
Electrical Short or Ground Fault
Symptom
Visible white or brown scale deposits on the evaporator fingers or inside the water tank.
Limescale Buildup
Symptom
Water leaking from the bottom of the ProfiCook ice maker onto the countertop or floor.
External Water Leak
Symptom
Water pooling inside the ice storage bin.
Poor Drainage / Meltwater Management Issue
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E1 |
Ice maker stops shortly after startup and displays E1 on the control panel.
|
Water Inlet Fault / Low Water Level Detection Error | View Details |
| E10 |
E10 appears and the machine stops; water may remain in the reservoir and no ice is produced.
|
Drain / Overflow Protection Error | View Details |
| E2 |
ProfiCook ice maker beeps and shows E2; unit powers on but does not start ice production.
|
Ice Full Sensor / Infrared Beam Obstruction | View Details |
| E3 |
Display shows E3 and the machine stops mid-cycle; compressor may not run or runs briefly.
|
Temperature Sensor (NTC) Fault on Evaporator | View Details |
| E4 |
E4 appears on the display; ice production stops and the fan may continue to run.
|
Refrigeration System Protection / Overheat or Overcool Error | View Details |
| E5 |
E5 error on display; machine powers on but does not harvest ice properly.
|
Ice Tray / Evaporator Position or Motor Fault | View Details |
| E6 |
E6 displayed; unit may start but stops with beeping before completing a cycle.
|
Water Pump Fault / Circulation Failure | View Details |
| E7 |
E7 appears on the display; unit may run but produces very little or no ice.
|
Ambient Temperature Sensor Fault | View Details |
| E8 |
E8 error code; machine may start but shuts down with beeping and no ice is produced.
|
Compressor Start / Overcurrent Protection Error | View Details |
| E9 |
E9 displayed; unit powers on but internal fan does not run and ice production is poor or absent.
|
Evaporator / Internal Fan Motor Fault | View Details |
| – |
Buttons on the control panel respond intermittently or require very hard presses.
|
Keypad Wear / Poor Contact | View Details |
| – |
Display is lit but segments are missing or unreadable.
|
Display Module / LED Segment Failure | View Details |
| – |
Grinding or scraping noise during ice harvest cycle.
|
Ice Tray Drive Mechanism Wear or Obstruction | View Details |
| – |
Ice cubes have a bad taste or odor.
|
Water Contamination / Internal Biofilm or Scale | View Details |
| – |
Ice cubes stick together in large clumps in the storage bin.
|
Ice Clumping / Overproduction Without Use | View Details |
| – |
Ice maker continuously runs and does not stop even when the bin is full.
|
Ice-Full Sensor Not Detecting | View Details |
| – |
Ice maker does not power on at all; no lights or display when plugged in.
|
No Power / Main Power Supply Failure | View Details |
| – |
Ice maker exterior becomes unusually hot to the touch during operation.
|
Overheating Cabinet / Poor Heat Rejection | View Details |
| – |
Ice maker interior surfaces sweat excessively, with condensation dripping into the bin.
|
Condensation Management Issue | View Details |
| – |
Ice maker is running but ice production is very slow compared to normal.
|
Reduced Cooling Efficiency | View Details |
| – |
Ice maker overflows water into the ice bin or out of the top.
|
Water Level Control Failure | View Details |
| – |
Ice maker produces hollow or thin-walled ice cubes.
|
Water Flow Imbalance / Short Fill Time | View Details |
| – |
Ice maker produces ice only for a short time, then stops until manually restarted.
|
Intermittent Control or Sensor Fault | View Details |
| – |
Ice maker produces ice, but cubes are very small and melt quickly.
|
Insufficient Cooling Capacity / Short Freeze Cycle | View Details |
| – |
Ice maker runs but makes a loud rattling or vibrating noise.
|
Mechanical Vibration / Loose Component | View Details |
| – |
Ice maker runs but produces no ice at all; evaporator plate does not get cold.
|
Refrigerant System Failure / No Cooling | View Details |
| – |
Ice maker runs but water does not flow over the evaporator or into the ice tray.
|
Water Circulation Failure | View Details |
| – |
Ice maker stops producing ice even though the bin is not full and no error code is shown.
|
False Ice-Full Detection | View Details |
| – |
Loud buzzing or humming noise from the rear of the unit, even when no ice is being produced.
|
Compressor or Fan Motor Noise | View Details |
| – |
Unit emits a plastic or burning smell during operation.
|
Overheating Component or Electrical Insulation Odor | View Details |
| – |
Unit frequently shuts off mid-cycle without any error code.
|
Thermal Overload / Power Interruption | View Details |
| – |
Unit powers on but does not start ice production when the START button is pressed.
|
User Interface / Control Panel Input Failure | View Details |
| – |
Unit trips the household circuit breaker or RCD when turned on.
|
Electrical Short or Ground Fault | View Details |
| – |
Visible white or brown scale deposits on the evaporator fingers or inside the water tank.
|
Limescale Buildup | View Details |
| – |
Water leaking from the bottom of the ProfiCook ice maker onto the countertop or floor.
|
External Water Leak | View Details |
| – |
Water pooling inside the ice storage bin.
|
Poor Drainage / Meltwater Management Issue | View Details |
No matching codes found
Advertisements