Parkside
Parkside Cordless Vacuums Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
B1
Battery indicator flashes B1 and vacuum will not start
Battery Overvoltage / Charger Fault Detected
B2
Battery indicator shows B2 and runtime is extremely short
Battery Capacity Degradation
E1
Cordless vacuum will not power on, battery LEDs flash once then turn off
Battery Pack Undervoltage Protection
E10
E10 error when attaching motorized accessories (mini turbo brush, floor head)
Accessory Recognition / Overload Fault
E2
Cordless vacuum shuts off within a few seconds of starting, even with fully charged battery
Overcurrent / Motor Overload Protection
E3
Cordless vacuum runs only at low power, turbo/high mode not available, E3 flashes on LED panel
Motor Driver Overtemperature / Thermal Protection
E4
LED display shows E4 and vacuum stops when using motorized floor brush
Brush Motor Overload / Jam Detection
E5
Vacuum stops and displays E5 when switching between speed modes
Speed Control / Hall Sensor Fault
E6
E6 error and vacuum will not start, battery LEDs show normal charge
Battery Pack Communication / Identification Error
E7
E7 displayed and vacuum cuts out when filter is dirty or bin is full
Airflow Sensor / Pressure Sensor Fault
E8
E8 error appears and vacuum stops after a few minutes of use
Overtemperature Protection – Motor Thermistor Trip
E9
E9 error and vacuum does not respond to trigger or power button
Trigger / Power Switch Circuit Fault
F1
F1 flashes on LED ring, vacuum pulses on and off rapidly
Intermittent Battery Connection Fault
F2
F2 error and vacuum runs only a few seconds on each trigger pull
Soft Start / Inrush Control Fault
F3
F3 error and vacuum cannot switch to eco/normal/turbo modes correctly
Mode Selector / Button Matrix Fault
F4
F4 error and vacuum indicates filter problem even after cleaning
Filter Presence / RFID Sensor Fault
F5
F5 error and vacuum cannot maintain suction, power cycles frequently
Cyclone Separation / Dust Bin Sensor Fault
Symptom
Charging LED on vacuum or charger blinks but battery does not charge
Charging Fault / Contact or BMS Issue
Symptom
Dust container door will not latch or pops open during use
Dust Bin Latch Failure
Symptom
Extension tube will not lock securely to main body or floor head
Locking Mechanism Wear
Symptom
Fine dust leaks from joints or around the dust container during use
Sealing / Gasket Failure
Symptom
LED battery indicator shows full, but vacuum stops after a minute
Battery Voltage Sag Under Load
Symptom
LEDs flicker or display segments fail while vacuum otherwise works
Display / LED Board Fault
Symptom
Motorized mini turbo brush stops frequently or runs intermittently
Accessory Motor / Connection Fault
Symptom
Vacuum body becomes very hot to touch during normal use
Inadequate Cooling / Blocked Exhaust
Symptom
Vacuum does not stand upright securely (for stick models with parking function)
Parking Lock / Hinge Wear
Symptom
Vacuum has very weak suction even though the motor sounds normal
Airflow Restriction / Loss of Sealing
Symptom
Vacuum leaves a bad or musty smell when running
Contaminated Filters / Dust Bin Odor
Symptom
Vacuum leaves lines of debris and does not pick up well from carpets
Brushroll Performance / Height Issue
Symptom
Vacuum makes clicking or popping sounds from the motor area
Arcing / Commutator Wear (Brushed Motor)
Symptom
Vacuum makes loud high‑pitched whine during operation
Motor Bearing Wear / Air Leak Noise
Symptom
Vacuum operates only in one speed mode regardless of button presses
Speed Control Button / Logic Fault
Symptom
Vacuum produces rattling or grinding noise from the floor head
Brushroll / Gearbox Damage
Symptom
Vacuum runs but emits a burning smell
Motor Overheating / Electrical Insulation Breakdown
Symptom
Vacuum runs but there is a noticeable loss of suction at the end of the extension tube
Partial Blockage / Tube Leak
Symptom
Vacuum shuts off randomly when tilted or moved
Intermittent Power / Loose Internal Connection
Symptom
Vacuum spits debris back out of the nozzle when turned off
Backflow / Check Valve Absence or Failure
Symptom
Vacuum trigger must be held very hard to keep unit running
Worn Trigger Mechanism / Microswitch Misalignment
Symptom
Vacuum will not start at all, no lights, but battery works in other Parkside tools
Main PCB Power Input Failure
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| B1 |
Battery indicator flashes B1 and vacuum will not start
|
Battery Overvoltage / Charger Fault Detected | View Details |
| B2 |
Battery indicator shows B2 and runtime is extremely short
|
Battery Capacity Degradation | View Details |
| E1 |
Cordless vacuum will not power on, battery LEDs flash once then turn off
|
Battery Pack Undervoltage Protection | View Details |
| E10 |
E10 error when attaching motorized accessories (mini turbo brush, floor head)
|
Accessory Recognition / Overload Fault | View Details |
| E2 |
Cordless vacuum shuts off within a few seconds of starting, even with fully charged battery
|
Overcurrent / Motor Overload Protection | View Details |
| E3 |
Cordless vacuum runs only at low power, turbo/high mode not available, E3 flashes on LED panel
|
Motor Driver Overtemperature / Thermal Protection | View Details |
| E4 |
LED display shows E4 and vacuum stops when using motorized floor brush
|
Brush Motor Overload / Jam Detection | View Details |
| E5 |
Vacuum stops and displays E5 when switching between speed modes
|
Speed Control / Hall Sensor Fault | View Details |
| E6 |
E6 error and vacuum will not start, battery LEDs show normal charge
|
Battery Pack Communication / Identification Error | View Details |
| E7 |
E7 displayed and vacuum cuts out when filter is dirty or bin is full
|
Airflow Sensor / Pressure Sensor Fault | View Details |
| E8 |
E8 error appears and vacuum stops after a few minutes of use
|
Overtemperature Protection – Motor Thermistor Trip | View Details |
| E9 |
E9 error and vacuum does not respond to trigger or power button
|
Trigger / Power Switch Circuit Fault | View Details |
| F1 |
F1 flashes on LED ring, vacuum pulses on and off rapidly
|
Intermittent Battery Connection Fault | View Details |
| F2 |
F2 error and vacuum runs only a few seconds on each trigger pull
|
Soft Start / Inrush Control Fault | View Details |
| F3 |
F3 error and vacuum cannot switch to eco/normal/turbo modes correctly
|
Mode Selector / Button Matrix Fault | View Details |
| F4 |
F4 error and vacuum indicates filter problem even after cleaning
|
Filter Presence / RFID Sensor Fault | View Details |
| F5 |
F5 error and vacuum cannot maintain suction, power cycles frequently
|
Cyclone Separation / Dust Bin Sensor Fault | View Details |
| – |
Charging LED on vacuum or charger blinks but battery does not charge
|
Charging Fault / Contact or BMS Issue | View Details |
| – |
Dust container door will not latch or pops open during use
|
Dust Bin Latch Failure | View Details |
| – |
Extension tube will not lock securely to main body or floor head
|
Locking Mechanism Wear | View Details |
| – |
Fine dust leaks from joints or around the dust container during use
|
Sealing / Gasket Failure | View Details |
| – |
LED battery indicator shows full, but vacuum stops after a minute
|
Battery Voltage Sag Under Load | View Details |
| – |
LEDs flicker or display segments fail while vacuum otherwise works
|
Display / LED Board Fault | View Details |
| – |
Motorized mini turbo brush stops frequently or runs intermittently
|
Accessory Motor / Connection Fault | View Details |
| – |
Vacuum body becomes very hot to touch during normal use
|
Inadequate Cooling / Blocked Exhaust | View Details |
| – |
Vacuum does not stand upright securely (for stick models with parking function)
|
Parking Lock / Hinge Wear | View Details |
| – |
Vacuum has very weak suction even though the motor sounds normal
|
Airflow Restriction / Loss of Sealing | View Details |
| – |
Vacuum leaves a bad or musty smell when running
|
Contaminated Filters / Dust Bin Odor | View Details |
| – |
Vacuum leaves lines of debris and does not pick up well from carpets
|
Brushroll Performance / Height Issue | View Details |
| – |
Vacuum makes clicking or popping sounds from the motor area
|
Arcing / Commutator Wear (Brushed Motor) | View Details |
| – |
Vacuum makes loud high‑pitched whine during operation
|
Motor Bearing Wear / Air Leak Noise | View Details |
| – |
Vacuum operates only in one speed mode regardless of button presses
|
Speed Control Button / Logic Fault | View Details |
| – |
Vacuum produces rattling or grinding noise from the floor head
|
Brushroll / Gearbox Damage | View Details |
| – |
Vacuum runs but emits a burning smell
|
Motor Overheating / Electrical Insulation Breakdown | View Details |
| – |
Vacuum runs but there is a noticeable loss of suction at the end of the extension tube
|
Partial Blockage / Tube Leak | View Details |
| – |
Vacuum shuts off randomly when tilted or moved
|
Intermittent Power / Loose Internal Connection | View Details |
| – |
Vacuum spits debris back out of the nozzle when turned off
|
Backflow / Check Valve Absence or Failure | View Details |
| – |
Vacuum trigger must be held very hard to keep unit running
|
Worn Trigger Mechanism / Microswitch Misalignment | View Details |
| – |
Vacuum will not start at all, no lights, but battery works in other Parkside tools
|
Main PCB Power Input Failure | View Details |
No matching codes found
Advertisements