Insinger Dishwashers Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E1
Machine will not fill; cycle will not start and display shows E1 shortly after start.
Fill Timeout / No Water Inlet
E10
Temperature sensor error; display shows E10 and machine may stop or run without proper temperature control.
Temperature Probe / Thermistor Fault
E11
Booster heater not reaching required rinse temperature; E11 displayed and machine may lock out sanitizing rinse.
Booster Heater Under-Temperature
E12
Low rinse pressure; final rinse appears weak or incomplete and E12 is shown.
Low Rinse Water Pressure / Flow
E13
Conveyor or rack drive not moving; conveyor-type Insinger dishwasher displays E13 and stops.
Conveyor / Rack Drive Failure
E14
Float switch error; machine may continuously fill or will not fill and E14 is displayed.
Float Switch / Overfill Protection Fault
E15
Leak detected in base pan; machine may stop and E15 is displayed (on models with leak sensor).
Base Pan Leak / Flood Sensor Activation
E16
Control communication error; display may be blank or show E16 and machine is unresponsive or erratic.
Control Board / User Interface Communication Fault
E17
Excessive fill time; machine eventually starts but E17 is logged or displayed.
Slow Fill / Restricted Inlet
E18
High temperature alarm; tank or booster temperature exceeds setpoint and E18 is displayed.
Over-Temperature Condition
E19
Sanitizing temperature not achieved; machine logs E19 and may fail health-code sanitization requirements.
Sanitizing Temperature Not Reached
E2
Dishwasher overfills, water level too high in tank or wash chamber, E2 displayed and machine may stop or drain continuously.
Overfill / Water Level Sensing Fault
E20
Chemical dosing error; control detects out-of-range detergent or rinse aid usage and shows E20.
Chemical Dosing / Flow Fault
E3
Dishwasher does not heat water; cycles run cold and E3 appears on the display.
Heating Circuit Failure
E4
Dishwasher does not drain; standing water remains in the tank or sump and E4 is displayed.
Drain Pump / Drain Circuit Failure
E5
Wash pump does not run; no spray pressure in the chamber and E5 appears on the control panel.
Wash Pump Motor Failure
E6
Rinse cycle does not activate; no final rinse spray and E6 is shown on the display.
Rinse Pump or Rinse Solenoid Failure
E7
Detergent is not dispensed during wash; E7 error appears on the control panel.
Detergent Dispenser / Pump Failure
E8
Rinse aid is not dispensed; spotting on dishes and E8 code displayed.
Rinse Aid Dispenser / Pump Failure
E9
Door or hood will not close cycle; machine will not start and E9 is displayed.
Door / Hood Interlock Failure
Symptom
Control panel buttons are unresponsive or require excessive force to operate.
User Interface Keypad Wear
Symptom
Detergent or rinse aid lines frequently lose prime and require manual priming.
Chemical Line Air Ingress
Symptom
Dishes not coming clean; food soil remains on plates and glasses after a full cycle.
Poor Wash Performance
Symptom
Dishwasher leaks water onto the floor during or after a cycle.
External Water Leak
Symptom
Dishwasher makes loud grinding or rattling noises during wash.
Mechanical Noise from Wash Pump or Spray System
Symptom
Dishwasher powers on but shuts off mid-cycle without completing wash or rinse.
Intermittent Power or Control Interruption
Symptom
Dishwasher vibrates excessively or moves during operation.
Vibration / Installation Issue
Symptom
Dishwasher will not start; no response when start button is pressed, but power is present at the unit.
No-Start Condition
Symptom
Display is dim, flickering, or completely blank, but machine may still run.
Display / HMI Failure
Symptom
Excessive spotting or filming on glassware after final rinse.
Rinse Quality / Spotting Issue
Symptom
Final rinse appears to be cold; dishes are not hot when exiting the machine.
Insufficient Final Rinse Temperature
Symptom
Racks do not advance smoothly through conveyor-type Insinger dishwasher; they stall or skew.
Rack Conveyance / Tracking Problem
Symptom
Rust spots appearing on racks or inside the tank.
Corrosion / Rust Formation
Symptom
Steam or hot moisture escaping excessively from door or hood during operation.
Steam Leakage / Poor Door Seal
Symptom
Strong chemical odor or visible chemical residue inside the tank or on dishes.
Over-Dosing of Detergent or Rinse Aid
Symptom
Water remains in the tank overnight; machine does not automatically drain when expected.
Incomplete or No Automatic Drain
Symptom
White chalky deposits or scale buildup inside tank, on heating elements, and on spray arms.
Lime Scale Accumulation
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E1 |
Machine will not fill; cycle will not start and display shows E1 shortly after start.
|
Fill Timeout / No Water Inlet | View Details |
| E10 |
Temperature sensor error; display shows E10 and machine may stop or run without proper temperature control.
|
Temperature Probe / Thermistor Fault | View Details |
| E11 |
Booster heater not reaching required rinse temperature; E11 displayed and machine may lock out sanitizing rinse.
|
Booster Heater Under-Temperature | View Details |
| E12 |
Low rinse pressure; final rinse appears weak or incomplete and E12 is shown.
|
Low Rinse Water Pressure / Flow | View Details |
| E13 |
Conveyor or rack drive not moving; conveyor-type Insinger dishwasher displays E13 and stops.
|
Conveyor / Rack Drive Failure | View Details |
| E14 |
Float switch error; machine may continuously fill or will not fill and E14 is displayed.
|
Float Switch / Overfill Protection Fault | View Details |
| E15 |
Leak detected in base pan; machine may stop and E15 is displayed (on models with leak sensor).
|
Base Pan Leak / Flood Sensor Activation | View Details |
| E16 |
Control communication error; display may be blank or show E16 and machine is unresponsive or erratic.
|
Control Board / User Interface Communication Fault | View Details |
| E17 |
Excessive fill time; machine eventually starts but E17 is logged or displayed.
|
Slow Fill / Restricted Inlet | View Details |
| E18 |
High temperature alarm; tank or booster temperature exceeds setpoint and E18 is displayed.
|
Over-Temperature Condition | View Details |
| E19 |
Sanitizing temperature not achieved; machine logs E19 and may fail health-code sanitization requirements.
|
Sanitizing Temperature Not Reached | View Details |
| E2 |
Dishwasher overfills, water level too high in tank or wash chamber, E2 displayed and machine may stop or drain continuously.
|
Overfill / Water Level Sensing Fault | View Details |
| E20 |
Chemical dosing error; control detects out-of-range detergent or rinse aid usage and shows E20.
|
Chemical Dosing / Flow Fault | View Details |
| E3 |
Dishwasher does not heat water; cycles run cold and E3 appears on the display.
|
Heating Circuit Failure | View Details |
| E4 |
Dishwasher does not drain; standing water remains in the tank or sump and E4 is displayed.
|
Drain Pump / Drain Circuit Failure | View Details |
| E5 |
Wash pump does not run; no spray pressure in the chamber and E5 appears on the control panel.
|
Wash Pump Motor Failure | View Details |
| E6 |
Rinse cycle does not activate; no final rinse spray and E6 is shown on the display.
|
Rinse Pump or Rinse Solenoid Failure | View Details |
| E7 |
Detergent is not dispensed during wash; E7 error appears on the control panel.
|
Detergent Dispenser / Pump Failure | View Details |
| E8 |
Rinse aid is not dispensed; spotting on dishes and E8 code displayed.
|
Rinse Aid Dispenser / Pump Failure | View Details |
| E9 |
Door or hood will not close cycle; machine will not start and E9 is displayed.
|
Door / Hood Interlock Failure | View Details |
| – |
Control panel buttons are unresponsive or require excessive force to operate.
|
User Interface Keypad Wear | View Details |
| – |
Detergent or rinse aid lines frequently lose prime and require manual priming.
|
Chemical Line Air Ingress | View Details |
| – |
Dishes not coming clean; food soil remains on plates and glasses after a full cycle.
|
Poor Wash Performance | View Details |
| – |
Dishwasher leaks water onto the floor during or after a cycle.
|
External Water Leak | View Details |
| – |
Dishwasher makes loud grinding or rattling noises during wash.
|
Mechanical Noise from Wash Pump or Spray System | View Details |
| – |
Dishwasher powers on but shuts off mid-cycle without completing wash or rinse.
|
Intermittent Power or Control Interruption | View Details |
| – |
Dishwasher vibrates excessively or moves during operation.
|
Vibration / Installation Issue | View Details |
| – |
Dishwasher will not start; no response when start button is pressed, but power is present at the unit.
|
No-Start Condition | View Details |
| – |
Display is dim, flickering, or completely blank, but machine may still run.
|
Display / HMI Failure | View Details |
| – |
Excessive spotting or filming on glassware after final rinse.
|
Rinse Quality / Spotting Issue | View Details |
| – |
Final rinse appears to be cold; dishes are not hot when exiting the machine.
|
Insufficient Final Rinse Temperature | View Details |
| – |
Racks do not advance smoothly through conveyor-type Insinger dishwasher; they stall or skew.
|
Rack Conveyance / Tracking Problem | View Details |
| – |
Rust spots appearing on racks or inside the tank.
|
Corrosion / Rust Formation | View Details |
| – |
Steam or hot moisture escaping excessively from door or hood during operation.
|
Steam Leakage / Poor Door Seal | View Details |
| – |
Strong chemical odor or visible chemical residue inside the tank or on dishes.
|
Over-Dosing of Detergent or Rinse Aid | View Details |
| – |
Water remains in the tank overnight; machine does not automatically drain when expected.
|
Incomplete or No Automatic Drain | View Details |
| – |
White chalky deposits or scale buildup inside tank, on heating elements, and on spray arms.
|
Lime Scale Accumulation | View Details |
No matching codes found
Advertisements