Saci
Saci Pool Pumps Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E01
Pump will not start, display shows E01 immediately after pressing START
Supply Undervoltage Protection
E02
Pump stops shortly after starting, display shows E02 and will not restart until power is cycled
Overcurrent / Motor Overload Trip
E03
Pump display shows E03 and motor does not run, sometimes accompanied by humming noise
Phase Loss / Phase Imbalance (for three‑phase Saci pumps)
E04
Pump stops during operation and shows E04, housing feels very hot to the touch
Motor Overtemperature Protection
E05
Variable‑speed Saci pump shows E05 and will not ramp up to set speed
Speed Sensor / Feedback Error
E06
Pump display shows E06 and motor does not start, sometimes after a power surge or lightning storm
Internal Drive / PCB Fault
E07
Pump shows E07 and stops, often when starting at high speed or under heavy load
Overload / Torque Limit Exceeded
E08
Pump display shows E08 and motor will not start, often after incorrect wiring changes
Incorrect Supply Frequency / Configuration Error
E09
Pump intermittently stops and shows E09, especially in damp environments
Ground Fault / Earth Leakage Detected
E10
Pump display shows E10 and ignores external control signals from automation system
Communication / External Control Error
E11
Pump shows E11 and cannot be programmed, buttons may be unresponsive
Keypad / User Interface Fault
E12
Pump display shows E12 and speed fluctuates unexpectedly
Internal Sensor Calibration Error
E13
Pump shows E13 and will not start after being idle for a long period
Stalled Rotor / Locked Rotor Detection
E14
Pump display shows E14 and unit runs only at minimum speed or shuts down
Internal Temperature Sensor Fault
E15
Pump shows E15 and cannot detect priming, shuts down after a short run
Priming Failure / Dry‑Run Protection
Symptom
Display on Saci variable‑speed pump is blank, but motor hums or runs
Display Power / Interface Failure
Symptom
Pump emits a burning smell during operation
Overheating Windings or Electrical Components
Symptom
Pump housing or nearby pipes vibrate excessively during operation
Excessive Vibration / Misalignment
Symptom
Pump intermittently stops when it rains or when the equipment area is wet
Moisture Ingress / Inadequate Weather Protection
Symptom
Pump is humming but will not start, then trips the breaker or thermal overload
Failed Start Capacitor / Stalled Motor
Symptom
Pump is noisy with a rattling or rumbling sound that changes with flow rate
Cavitation / Hydraulic Noise
Symptom
Pump is very noisy, with a loud grinding or screeching sound from the motor end
Worn Motor Bearings
Symptom
Pump makes a loud clicking or knocking noise once per revolution
Impeller or Fan Obstruction
Symptom
Pump motor is extremely hot to the touch but continues running
Overheating Without Trip
Symptom
Pump runs but causes frequent nuisance tripping of the RCD/GFCI
Earth Leakage / Insulation Degradation
Symptom
Pump runs but filter pressure is much higher than normal and flow is reduced
Discharge Restriction / Dirty Filter
Symptom
Pump runs but pool circulation is weak and filter pressure is lower than normal
Suction Side Air Leak / Partial Blockage
Symptom
Pump runs but there is no water flow or only a weak trickle from the pool returns
Loss of Prime / Suction Restriction
Symptom
Pump runs but water leaks steadily from the joint between the pump housing and motor
Failed Mechanical Seal
Symptom
Pump speed on variable‑speed Saci model does not change even when different speeds are selected
Speed Control / Drive Output Fault
Symptom
Pump starts and stops repeatedly every few seconds (short cycling)
Control Instability / Protection Cycling
Symptom
Pump trips the circuit breaker immediately when switched on
Electrical Short Circuit
Symptom
Pump will not start at scheduled times but runs when started manually
Timer / Programming Issue
Symptom
Pump will not turn off from the keypad, only by cutting power at the breaker
Stuck Relay / Control Fault
Symptom
Water leaking from the clear pump lid area when the pump is running
Damaged Pump Lid O‑Ring / Cracked Lid
Symptom
Water leaking from the drain plugs at the bottom of the Saci pump housing
Leaking Drain Plug Gaskets
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E01 |
Pump will not start, display shows E01 immediately after pressing START
|
Supply Undervoltage Protection | View Details |
| E02 |
Pump stops shortly after starting, display shows E02 and will not restart until power is cycled
|
Overcurrent / Motor Overload Trip | View Details |
| E03 |
Pump display shows E03 and motor does not run, sometimes accompanied by humming noise
|
Phase Loss / Phase Imbalance (for three‑phase Saci pumps) | View Details |
| E04 |
Pump stops during operation and shows E04, housing feels very hot to the touch
|
Motor Overtemperature Protection | View Details |
| E05 |
Variable‑speed Saci pump shows E05 and will not ramp up to set speed
|
Speed Sensor / Feedback Error | View Details |
| E06 |
Pump display shows E06 and motor does not start, sometimes after a power surge or lightning storm
|
Internal Drive / PCB Fault | View Details |
| E07 |
Pump shows E07 and stops, often when starting at high speed or under heavy load
|
Overload / Torque Limit Exceeded | View Details |
| E08 |
Pump display shows E08 and motor will not start, often after incorrect wiring changes
|
Incorrect Supply Frequency / Configuration Error | View Details |
| E09 |
Pump intermittently stops and shows E09, especially in damp environments
|
Ground Fault / Earth Leakage Detected | View Details |
| E10 |
Pump display shows E10 and ignores external control signals from automation system
|
Communication / External Control Error | View Details |
| E11 |
Pump shows E11 and cannot be programmed, buttons may be unresponsive
|
Keypad / User Interface Fault | View Details |
| E12 |
Pump display shows E12 and speed fluctuates unexpectedly
|
Internal Sensor Calibration Error | View Details |
| E13 |
Pump shows E13 and will not start after being idle for a long period
|
Stalled Rotor / Locked Rotor Detection | View Details |
| E14 |
Pump display shows E14 and unit runs only at minimum speed or shuts down
|
Internal Temperature Sensor Fault | View Details |
| E15 |
Pump shows E15 and cannot detect priming, shuts down after a short run
|
Priming Failure / Dry‑Run Protection | View Details |
| – |
Display on Saci variable‑speed pump is blank, but motor hums or runs
|
Display Power / Interface Failure | View Details |
| – |
Pump emits a burning smell during operation
|
Overheating Windings or Electrical Components | View Details |
| – |
Pump housing or nearby pipes vibrate excessively during operation
|
Excessive Vibration / Misalignment | View Details |
| – |
Pump intermittently stops when it rains or when the equipment area is wet
|
Moisture Ingress / Inadequate Weather Protection | View Details |
| – |
Pump is humming but will not start, then trips the breaker or thermal overload
|
Failed Start Capacitor / Stalled Motor | View Details |
| – |
Pump is noisy with a rattling or rumbling sound that changes with flow rate
|
Cavitation / Hydraulic Noise | View Details |
| – |
Pump is very noisy, with a loud grinding or screeching sound from the motor end
|
Worn Motor Bearings | View Details |
| – |
Pump makes a loud clicking or knocking noise once per revolution
|
Impeller or Fan Obstruction | View Details |
| – |
Pump motor is extremely hot to the touch but continues running
|
Overheating Without Trip | View Details |
| – |
Pump runs but causes frequent nuisance tripping of the RCD/GFCI
|
Earth Leakage / Insulation Degradation | View Details |
| – |
Pump runs but filter pressure is much higher than normal and flow is reduced
|
Discharge Restriction / Dirty Filter | View Details |
| – |
Pump runs but pool circulation is weak and filter pressure is lower than normal
|
Suction Side Air Leak / Partial Blockage | View Details |
| – |
Pump runs but there is no water flow or only a weak trickle from the pool returns
|
Loss of Prime / Suction Restriction | View Details |
| – |
Pump runs but water leaks steadily from the joint between the pump housing and motor
|
Failed Mechanical Seal | View Details |
| – |
Pump speed on variable‑speed Saci model does not change even when different speeds are selected
|
Speed Control / Drive Output Fault | View Details |
| – |
Pump starts and stops repeatedly every few seconds (short cycling)
|
Control Instability / Protection Cycling | View Details |
| – |
Pump trips the circuit breaker immediately when switched on
|
Electrical Short Circuit | View Details |
| – |
Pump will not start at scheduled times but runs when started manually
|
Timer / Programming Issue | View Details |
| – |
Pump will not turn off from the keypad, only by cutting power at the breaker
|
Stuck Relay / Control Fault | View Details |
| – |
Water leaking from the clear pump lid area when the pump is running
|
Damaged Pump Lid O‑Ring / Cracked Lid | View Details |
| – |
Water leaking from the drain plugs at the bottom of the Saci pump housing
|
Leaking Drain Plug Gaskets | View Details |
No matching codes found
Advertisements