Camry Cordless Vacuums Error Codes

E1

Vacuum will not power on; display shows E1 shortly after pressing the power button

Main Battery Pack Undervoltage Protection

E10

Vacuum display shows E10; unit does not respond to mode changes or trigger

User Interface / Keypad Communication Error

E11

Vacuum shows E11 and cannot switch to MAX/Turbo mode

High-Power Mode Current Limit Exceeded

E12

Vacuum shows E12 and shuts down when using motorized mini tool or pet brush

Accessory Motor Overload / Short

E13

Vacuum shows E13; battery percentage reading is erratic or stuck

Battery Calibration / Fuel Gauge Error

E14

Vacuum shows E14 and emits a beeping tone; motor does not start

Motor Tachometer / Speed Feedback Error

E15

Vacuum shows E15; unit vibrates briefly then shuts off

Rotor Imbalance / Severe Vibration Protection

E2

Vacuum powers on but shuts off within a few seconds; display shows E2

Battery Overcurrent / Short Circuit Protection

E3

Vacuum stops during use and displays E3; may restart after cooling

Motor Overheating Protection

E4

Vacuum will not start; display shows E4 and battery icon flashes

Battery Overtemperature Protection

E5

Vacuum does not charge; display shows E5 or charger LED blinks rapidly

Charger / Power Supply Fault

E6

Vacuum runs but suction is very weak; display shows E6 and filter icon

Filter Blockage / Filter Not Installed Correctly

E7

Brush head stops spinning; display shows E7 or brush icon with error

Motorized Floor Head Overload / Jam Protection

E8

Vacuum display shows E8 and unit will not start; often after a drop or impact

Internal Communication Error Between Control PCB and Motor Driver

E9

Vacuum shows E9 and power level LEDs flash; unit may pulse on and off

Airflow Sensor / Pressure Sensor Fault

Symptom

Battery drains very quickly; runtime much shorter than specified

Battery Capacity Degradation

Symptom

Battery will not charge past a certain percentage (e.g., stuck at 60%)

Partial Cell Failure / Charge Termination Issue

Symptom

Clicking or rattling noise from the brush head while in use

Brush Roll / Gearbox Wear

Symptom

Dust bin door will not latch closed or pops open during use

Bin Latch / Hinge Failure

Symptom

Motorized floor head does not spin, but suction works normally (no error code)

Brush Head Power Loss

Symptom

Static shocks felt when touching the vacuum body or wand during use

Static Electricity Buildup

Symptom

Vacuum body creaks or flexes; joints feel loose during use

Structural Wear / Loose Housing

Symptom

Vacuum cuts out when tilting or moving the wand in certain directions

Intermittent Wand / Head Electrical Connection

Symptom

Vacuum emits a burning smell or hot plastic odor during or after use

Overheating Motor or Brush Head

Symptom

Vacuum handle or battery area becomes uncomfortably hot during normal use

Battery or Electronics Overheating

Symptom

Vacuum has very weak suction even though the motor sounds normal

Airflow Restriction / Loss of Seal

Symptom

Vacuum is excessively loud compared to normal operation

Mechanical Wear or Air Leak Noise

Symptom

Vacuum leaves debris on carpet; brush spins but pickup is poor

Ineffective Agitation / Worn Brush Roll

Symptom

Vacuum leaves fine dust haze in the air; exhaust feels dusty

Filtration Failure / Bypass Leak

Symptom

Vacuum makes a high-pitched whistling noise during use

Air Leak at Seals or Cracks

Symptom

Vacuum runs only on low power; cannot switch to higher modes (no code shown)

Mode Selection / Power Limiting Fault

Symptom

Vacuum smells musty or emits unpleasant odor from exhaust

Odor Contamination in Filters or Bin

Symptom

Vacuum spits debris back out of the nozzle when turned off

Debris Fall-Back / Check Valve Issue

Symptom

Vacuum turns on but shuts off after a few seconds with no error code

Intermittent Power / Loose Connection

Symptom

Vacuum will not turn on at all; no lights or response when pressing power

Complete Power Loss