AEG Ranges & Cooktops Error Codes

d

Display shows 'd' or 'demo' and zones heat only very weakly or not at all

Demo Mode Activated

E0

Induction hob will not operate, display shows E0 on one or more zones

Pan Detection Failure

E1

Induction hob zone shuts down shortly after switching on, display shows E1

Cookware Overheating or Dry-Boil Protection

E2

Induction hob zone stops and displays E2 during cooking

Induction Zone Overheating Protection

E3

Induction hob displays E3 and will not heat on one or more zones

Supply Voltage Too High

E4

Induction hob displays E4 and zone does not heat

Supply Voltage Too Low or Power Module Undervoltage

E5

Induction hob shows E5 and shuts down or refuses to start

Hob Electronics Overheating

E6

Induction hob displays E6 and zones are disabled

Internal Communication Error Between User Interface and Power Module

E7

Induction hob shows E7 on a specific zone, no heating

Induction Coil or Power Stage Failure

E8

Induction hob displays E8 and beeps, zone cannot be used

Configuration or Calibration Error

E9

Induction hob shows E9 and shuts down all zones

Internal Electronics Fault / Power Module Failure

Er03

Induction or ceramic hob shows Er03 and beeps, controls locked

Control Panel Contaminated or Continuous Key Press Detected

Er22

Hob displays Er22 and does not respond to touch

Touch Control Calibration Error

Er47

Induction hob shows Er47 and affected zone is disabled

Power Module Overcurrent or Short-Circuit Protection

F

Induction hob or ceramic hob shows flashing 'F' on a zone display

No Pan Detected / Incompatible Cookware

F1

AEG gas hob with electronic ignition shows F1 and burners will not ignite

Ignition System Fault

F2

AEG gas hob shows F2, burners shut off automatically

Flame Supervision Device (FSD) / Thermocouple Fault

F3

AEG gas hob shows F3 and ignition clicks continuously

Stuck Ignition Switch or Wet Control

F4

AEG gas hob shows F4 and shuts off burner shortly after ignition

Flame Detection Error

F5

AEG gas hob shows F5 and all burners are disabled

Gas Safety System General Fault

L

Hob display shows 'L' and controls do not respond

Child Lock / Control Lock Activated

Symptom

Burner on gas hob will not ignite, no clicking sound

Ignition System Inoperative

Symptom

Gas hob burner ignites but goes out when knob is released

Flame Failure Device Not Holding

Symptom

Gas hob burner produces yellow, sooty, or uneven flame

Poor Combustion / Burner Contamination

Symptom

Gas hob ignition keeps clicking even after flame is lit

Stuck Ignition Switch / Continuous Spark

Symptom

Glass ceramic surface cracked or shattered

Glass Hob Top Damage

Symptom

Hob causes circuit breaker or RCD to trip when turned on

Electrical Short or Earth Leakage

Symptom

Hob controls unresponsive, cannot change power level or turn zones on

Touch Control Panel Failure

Symptom

Hob emits burning smell or smoke from vents during operation

Overheating or Component Failure

Symptom

Hob makes loud buzzing or humming noise when using induction zones

Induction Acoustic Noise / Coil Vibration

Symptom

Hob surface around zones discoloured or stained

Cosmetic Damage / Heat Staining

Symptom

Hob turns itself off during cooking without error code

Overheating or Auto-Safety Shutoff

Symptom

Induction hob does not power on at all, no lights or display

No Power / Dead Appliance

Symptom

Induction hob intermittently shuts off when using multiple zones at high power

Power Management / Load Limitation

Symptom

Induction or ceramic hob powers on but individual zone will not heat

Single Cooking Zone Failure

Symptom

Residual heat indicator stays on even when zone is cold

Residual Heat Sensor or Logic Fault

Symptom

Strong gas smell around AEG gas hob during or after use

Gas Leak or Incomplete Combustion

Symptom

Timer function on hob does not work or zones do not switch off when timer ends

Timer Control Fault