Electrolux Washer-Dryer Combos Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E10
Washer-dryer combo will not fill with water or takes a very long time to fill; cycle may abort with E10 displayed.
Water Inlet Fill Timeout
E11
Washer-dryer combo does not reach the required water level within the expected time; E11 displayed early in the cycle.
Water Level Not Reached (Fill Timeout)
E13
Water detected in the bottom base pan; washer-dryer may stop mid-cycle and display E13, sometimes accompanied by drain pump running continuously.
Leak Detected in Base (Flood Protection Activated)
E20
Washer-dryer combo will not drain or drains very slowly; cycle may stop with E20 displayed and clothes remain wet.
Drain Pump or Drainage Fault
E21
Washer-dryer combo stops with water still in the drum; E21 displayed, often after an extended drain attempt.
Drain Time Exceeded
E23
Washer-dryer combo may not drain or may show E23; sometimes the pump does not run at all when drain is requested.
Drain Pump Relay or Triac Fault on Control Board
E24
Washer-dryer combo displays E24 and may not drain; often associated with control board sensing an electrical fault in the drain circuit.
Drain Pump Circuit Error
E30
Washer-dryer combo stops and displays E30; may be accompanied by water in the base or leak detection behavior.
General Leak / Water Protection Error
E31
Washer-dryer combo may overfill or underfill; E31 displayed indicating a water level sensing issue.
Pressure Sensor Signal Fault
E32
Washer-dryer combo shows E32 and may have erratic filling or spinning behavior.
Pressure Sensor Calibration / Range Error
E33
Washer-dryer combo displays E33; may have issues with heating or water level control.
Pressure System / Heater Interlock Fault
E34
Washer-dryer combo shows E34 and may refuse to start or heat.
Pressure Switch / Control Board Communication Error
E35
Washer-dryer combo overfills with water or shows E35; may trigger drain pump and stop cycle.
Overfill / Overpressure Detected
E38
Washer-dryer combo shows E38; may have incorrect water levels or poor rinsing.
Blocked Air Trap / Pressure System Restriction
E40
Washer-dryer combo will not start; E40 displayed and door may not lock properly.
Door Locking System Error
E41
Washer-dryer combo displays E41; control thinks the door is open even when closed.
Door Open Signal Fault
E42
Washer-dryer combo door will not unlock at end of cycle; E42 may be displayed.
Door Unlock Fault
E43
Washer-dryer combo shows E43 and may not start; often related to door lock control circuitry.
Door Lock Triac / Control Board Fault
E44
Washer-dryer combo displays E44; door status signal inconsistent.
Door Status Sensor Error
E45
Washer-dryer combo shows E45; advanced door lock/control communication error.
Door Lock Communication / Configuration Fault
E50
Washer-dryer combo will not spin or tumble; E50 displayed indicating a motor-related fault.
General Motor Drive Error
E51
Washer-dryer combo shows E51; motor does not run or only jerks.
Motor Power Triac Short-Circuit
E52
Washer-dryer combo drum may spin erratically or not at all; E52 displayed.
Tachometer Signal Missing or Invalid
E53
Washer-dryer combo shows E53; motor may not respond correctly to speed commands.
Motor Control Circuit Error
E54
Washer-dryer combo may stop during spin; E54 displayed.
Motor Relay Stuck or Faulty
E60
Washer-dryer combo has drying problems (no heat or overheating); E60 displayed as a general heating error.
General Drying Heater / Heating System Fault
E61
Washer-dryer combo does not reach target drying temperature; clothes remain damp; E61 displayed.
Dryer Heating Performance Low
E62
Washer-dryer combo overheats during drying; may stop and display E62.
Dryer Overheating Detected
E66
Washer-dryer combo shows E66; dryer heater does not energize.
Heater Relay Fault
E70
Washer-dryer combo shows E70; temperature sensing issues in wash or dry cycles.
NTC Temperature Sensor Circuit Fault
E90
Washer-dryer combo displays E90; often indicates a communication or configuration problem.
Main Control / User Interface Communication Error
E91
Washer-dryer combo shows E91; no or invalid communication with user interface.
User Interface Communication Fault
E92
Washer-dryer combo displays E92; configuration mismatch or corrupted settings.
Configuration / EEPROM Error
E93
Washer-dryer combo shows E93; internal configuration error.
Configuration Parameter Fault
E94
Washer-dryer combo displays E94; program or cycle configuration error.
Program Configuration Fault
E95
Washer-dryer combo shows E95; internal communication or memory error.
Control Board Internal Communication Fault
E96
Washer-dryer combo displays E96; hardware configuration mismatch.
Hardware Configuration Error
E97
Washer-dryer combo shows E97; program selector and control board mismatch.
Program Selector / Control Board Incompatibility
E98
Washer-dryer combo displays E98; severe communication error between boards.
Main Control and Motor/Power Board Communication Fault
Symptom
Washer-dryer combo display works but buttons are unresponsive or respond erratically.
User Interface Keypad Failure
Symptom
Washer-dryer combo does not dry clothes effectively; clothes come out damp or wet after drying cycle completes.
Poor Drying Performance
Symptom
Washer-dryer combo door is stuck locked with no error code after a power outage or interruption.
Door Lock Latched After Power Loss
Symptom
Washer-dryer combo drum does not turn during wash or dry, but the unit powers on and fills/drains normally.
Drive Belt or Motor Failure
Symptom
Washer-dryer combo emits a burning smell during drying or high-temperature wash.
Overheating or Foreign Object on Heater
Symptom
Washer-dryer combo has a persistent musty or moldy odor inside the drum.
Biofilm and Mold Build-Up
Symptom
Washer-dryer combo intermittently trips the household circuit breaker or RCD during operation.
Electrical Short or Ground Fault
Symptom
Washer-dryer combo leaks from the rear or underneath during drain or spin; no error code.
Internal Hose or Pump Leak
Symptom
Washer-dryer combo leaks water from the front, especially during wash or spin; no error code displayed.
Door Boot (Bellows) Leak
Symptom
Washer-dryer combo leaves clothes very wet at the end of the cycle; no spin error code shown.
Poor Final Spin / Out-of-Balance Spin Abort
Symptom
Washer-dryer combo leaves detergent or fabric softener in the dispenser drawer at the end of the cycle.
Poor Dispenser Flushing
Symptom
Washer-dryer combo makes loud banging or knocking noises during spin; drum may hit the cabinet.
Suspension or Shock Absorber Failure
Symptom
Washer-dryer combo produces a high-pitched squeal or grinding noise when spinning or tumbling.
Drum Bearing or Drive System Wear
Symptom
Washer-dryer combo vibrates excessively or "walks" across the floor during spin; no error code.
Excessive Vibration / Out-of-Balance Condition
Symptom
Washer-dryer combo will not power on at all; no lights or display.
No Power / Dead Appliance
Symptom
Washer-dryer combo will not start a cycle; display is on but pressing start does nothing.
Start Inhibit / Safety Interlock Not Satisfied
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E10 |
Washer-dryer combo will not fill with water or takes a very long time to fill; cycle may abort with E10 displayed.
|
Water Inlet Fill Timeout | View Details |
| E11 |
Washer-dryer combo does not reach the required water level within the expected time; E11 displayed early in the cycle.
|
Water Level Not Reached (Fill Timeout) | View Details |
| E13 |
Water detected in the bottom base pan; washer-dryer may stop mid-cycle and display E13, sometimes accompanied by drain pump running continuously.
|
Leak Detected in Base (Flood Protection Activated) | View Details |
| E20 |
Washer-dryer combo will not drain or drains very slowly; cycle may stop with E20 displayed and clothes remain wet.
|
Drain Pump or Drainage Fault | View Details |
| E21 |
Washer-dryer combo stops with water still in the drum; E21 displayed, often after an extended drain attempt.
|
Drain Time Exceeded | View Details |
| E23 |
Washer-dryer combo may not drain or may show E23; sometimes the pump does not run at all when drain is requested.
|
Drain Pump Relay or Triac Fault on Control Board | View Details |
| E24 |
Washer-dryer combo displays E24 and may not drain; often associated with control board sensing an electrical fault in the drain circuit.
|
Drain Pump Circuit Error | View Details |
| E30 |
Washer-dryer combo stops and displays E30; may be accompanied by water in the base or leak detection behavior.
|
General Leak / Water Protection Error | View Details |
| E31 |
Washer-dryer combo may overfill or underfill; E31 displayed indicating a water level sensing issue.
|
Pressure Sensor Signal Fault | View Details |
| E32 |
Washer-dryer combo shows E32 and may have erratic filling or spinning behavior.
|
Pressure Sensor Calibration / Range Error | View Details |
| E33 |
Washer-dryer combo displays E33; may have issues with heating or water level control.
|
Pressure System / Heater Interlock Fault | View Details |
| E34 |
Washer-dryer combo shows E34 and may refuse to start or heat.
|
Pressure Switch / Control Board Communication Error | View Details |
| E35 |
Washer-dryer combo overfills with water or shows E35; may trigger drain pump and stop cycle.
|
Overfill / Overpressure Detected | View Details |
| E38 |
Washer-dryer combo shows E38; may have incorrect water levels or poor rinsing.
|
Blocked Air Trap / Pressure System Restriction | View Details |
| E40 |
Washer-dryer combo will not start; E40 displayed and door may not lock properly.
|
Door Locking System Error | View Details |
| E41 |
Washer-dryer combo displays E41; control thinks the door is open even when closed.
|
Door Open Signal Fault | View Details |
| E42 |
Washer-dryer combo door will not unlock at end of cycle; E42 may be displayed.
|
Door Unlock Fault | View Details |
| E43 |
Washer-dryer combo shows E43 and may not start; often related to door lock control circuitry.
|
Door Lock Triac / Control Board Fault | View Details |
| E44 |
Washer-dryer combo displays E44; door status signal inconsistent.
|
Door Status Sensor Error | View Details |
| E45 |
Washer-dryer combo shows E45; advanced door lock/control communication error.
|
Door Lock Communication / Configuration Fault | View Details |
| E50 |
Washer-dryer combo will not spin or tumble; E50 displayed indicating a motor-related fault.
|
General Motor Drive Error | View Details |
| E51 |
Washer-dryer combo shows E51; motor does not run or only jerks.
|
Motor Power Triac Short-Circuit | View Details |
| E52 |
Washer-dryer combo drum may spin erratically or not at all; E52 displayed.
|
Tachometer Signal Missing or Invalid | View Details |
| E53 |
Washer-dryer combo shows E53; motor may not respond correctly to speed commands.
|
Motor Control Circuit Error | View Details |
| E54 |
Washer-dryer combo may stop during spin; E54 displayed.
|
Motor Relay Stuck or Faulty | View Details |
| E60 |
Washer-dryer combo has drying problems (no heat or overheating); E60 displayed as a general heating error.
|
General Drying Heater / Heating System Fault | View Details |
| E61 |
Washer-dryer combo does not reach target drying temperature; clothes remain damp; E61 displayed.
|
Dryer Heating Performance Low | View Details |
| E62 |
Washer-dryer combo overheats during drying; may stop and display E62.
|
Dryer Overheating Detected | View Details |
| E66 |
Washer-dryer combo shows E66; dryer heater does not energize.
|
Heater Relay Fault | View Details |
| E70 |
Washer-dryer combo shows E70; temperature sensing issues in wash or dry cycles.
|
NTC Temperature Sensor Circuit Fault | View Details |
| E90 |
Washer-dryer combo displays E90; often indicates a communication or configuration problem.
|
Main Control / User Interface Communication Error | View Details |
| E91 |
Washer-dryer combo shows E91; no or invalid communication with user interface.
|
User Interface Communication Fault | View Details |
| E92 |
Washer-dryer combo displays E92; configuration mismatch or corrupted settings.
|
Configuration / EEPROM Error | View Details |
| E93 |
Washer-dryer combo shows E93; internal configuration error.
|
Configuration Parameter Fault | View Details |
| E94 |
Washer-dryer combo displays E94; program or cycle configuration error.
|
Program Configuration Fault | View Details |
| E95 |
Washer-dryer combo shows E95; internal communication or memory error.
|
Control Board Internal Communication Fault | View Details |
| E96 |
Washer-dryer combo displays E96; hardware configuration mismatch.
|
Hardware Configuration Error | View Details |
| E97 |
Washer-dryer combo shows E97; program selector and control board mismatch.
|
Program Selector / Control Board Incompatibility | View Details |
| E98 |
Washer-dryer combo displays E98; severe communication error between boards.
|
Main Control and Motor/Power Board Communication Fault | View Details |
| – |
Washer-dryer combo display works but buttons are unresponsive or respond erratically.
|
User Interface Keypad Failure | View Details |
| – |
Washer-dryer combo does not dry clothes effectively; clothes come out damp or wet after drying cycle completes.
|
Poor Drying Performance | View Details |
| – |
Washer-dryer combo door is stuck locked with no error code after a power outage or interruption.
|
Door Lock Latched After Power Loss | View Details |
| – |
Washer-dryer combo drum does not turn during wash or dry, but the unit powers on and fills/drains normally.
|
Drive Belt or Motor Failure | View Details |
| – |
Washer-dryer combo emits a burning smell during drying or high-temperature wash.
|
Overheating or Foreign Object on Heater | View Details |
| – |
Washer-dryer combo has a persistent musty or moldy odor inside the drum.
|
Biofilm and Mold Build-Up | View Details |
| – |
Washer-dryer combo intermittently trips the household circuit breaker or RCD during operation.
|
Electrical Short or Ground Fault | View Details |
| – |
Washer-dryer combo leaks from the rear or underneath during drain or spin; no error code.
|
Internal Hose or Pump Leak | View Details |
| – |
Washer-dryer combo leaks water from the front, especially during wash or spin; no error code displayed.
|
Door Boot (Bellows) Leak | View Details |
| – |
Washer-dryer combo leaves clothes very wet at the end of the cycle; no spin error code shown.
|
Poor Final Spin / Out-of-Balance Spin Abort | View Details |
| – |
Washer-dryer combo leaves detergent or fabric softener in the dispenser drawer at the end of the cycle.
|
Poor Dispenser Flushing | View Details |
| – |
Washer-dryer combo makes loud banging or knocking noises during spin; drum may hit the cabinet.
|
Suspension or Shock Absorber Failure | View Details |
| – |
Washer-dryer combo produces a high-pitched squeal or grinding noise when spinning or tumbling.
|
Drum Bearing or Drive System Wear | View Details |
| – |
Washer-dryer combo vibrates excessively or "walks" across the floor during spin; no error code.
|
Excessive Vibration / Out-of-Balance Condition | View Details |
| – |
Washer-dryer combo will not power on at all; no lights or display.
|
No Power / Dead Appliance | View Details |
| – |
Washer-dryer combo will not start a cycle; display is on but pressing start does nothing.
|
Start Inhibit / Safety Interlock Not Satisfied | View Details |
No matching codes found
Advertisements