Little Swan Washing Machines Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E1
Washer does not fill with water; after a few minutes it stops and displays E1.
Water Inlet Timeout / No Fill
E10
Washer displays E10 and will not start or stops shortly after starting.
Communication Error Between Main PCB and Inverter/Display
E11
Washer shows E11 and the door remains locked at the end of the cycle.
Door Unlock Failure
E12
Washer displays E12 and may stop heating or show erratic temperature behavior.
NTC Temperature Sensor Fault
E13
Washer shows E13 and may stop with water remaining in the tub or leak detected.
Leakage / Floor Pan Float Switch Activated
E2
Washer does not drain water; drum remains full and E2 is displayed.
Drain Timeout / No Drain
E21
Front-load Little Swan washer shows E21 and will not drain or spin.
Drain Pump Blocked / Slow Drain
E23
Washer displays E23 and may stop mid-cycle with water in the tub.
Drain Pump Triac / Control Fault
E3
Washer drum spins abnormally fast or slow, or stops unexpectedly during spin and shows E3.
Motor Tachometer / Speed Sensor Error
E30
Washer shows E30 and will not start; door may not lock properly.
Door Lock Circuit Error
E31
Washer displays E31 and water level reading is unstable or incorrect.
Pressure Sensor Calibration / Signal Error
E32
Washer shows E32 and may not spin or may stop with water in the drum.
Unbalanced Detection / Spin Protection Error
E4
Washer vibrates excessively or refuses to spin and displays E4.
Unbalanced Load / Vibration Protection
E40
Washer displays E40 and will not start; door symbol may flash.
Door Not Properly Closed
E41
Washer shows E41 even though the door appears closed.
Door Open Signal Error
E5
Washer door does not lock at the start of a cycle and E5 is displayed.
Door Lock Failure
E51
Washer displays E51 and will not spin or wash; motor does not run.
Motor Power Triac / Drive Circuit Error
E52
Washer shows E52; drum may start then stop repeatedly.
No Motor Tachometer Signal
E6
Washer stops mid-cycle and displays E6; drum may not rotate properly.
Motor Drive Fault / Overload
E60
Washer displays E60 and will not heat water or stops during heating phase.
General Heating System Error
E7
Washer displays E7 and may not start or may stop unexpectedly; water level seems incorrect.
Water Level Sensor (Pressure Switch) Error
E8
Washer displays E8 and may not heat water or may stop during wash.
Water Heating Fault
E9
Washer shows E9 and may leak or overfill; water level appears abnormal.
Overflow / Overfill Protection
E90
Washer shows E90 and is unresponsive or stuck at startup.
Configuration / EEPROM / Communication Error
Symptom
Top-load Little Swan washer does not agitate or spin, but fills and drains normally.
Clutch / Transmission or Drive System Failure (Top-Load)
Symptom
Washer display and buttons work, but cycle will not start when pressing Start/Pause.
Start Circuit / User Interface Logic Issue
Symptom
Washer does not spin clothes dry; clothes come out very wet, but machine completes the cycle.
Poor Spin Performance
Symptom
Washer does not take detergent or softener from the dispenser drawer.
Dispenser Drawer Water Flow Restriction
Symptom
Washer door will not open at the end of the cycle, but no error code is shown.
Door Stuck Locked After Cycle
Symptom
Washer emits a burning smell during operation.
Overheating Electrical or Mechanical Component
Symptom
Washer fills and drains but the drum does not rotate during wash or spin; no error code displayed.
Drive Motor Not Running
Symptom
Washer has a strong moldy or sewer-like odor inside the drum.
Biofilm and Detergent Residue Buildup
Symptom
Washer is very noisy during spin; grinding or rumbling sound from the drum area.
Tub Bearing and/or Spider Arm Failure
Symptom
Washer leaks water from the front during wash or spin.
Door Gasket (Bellows) Leak
Symptom
Washer leaks water from the rear or bottom during operation.
Internal Hose or Tub Seal Leak
Symptom
Washer leaves visible detergent or powder residue on clothes after washing.
Poor Rinsing / Detergent Dissolution Issue
Symptom
Washer makes a loud banging or knocking noise during spin.
Severe Out-of-Balance or Suspension Failure
Symptom
Washer stops mid-cycle and all lights go off, then comes back on later.
Intermittent Power Loss / Overheating Protection
Symptom
Washer takes much longer than the displayed time to finish a cycle.
Cycle Time Extension / Auto-Balancing and Heating Delays
Symptom
Washer vibrates excessively and "walks" across the floor during spin, but no error code appears.
Excessive Vibration / Poor Installation
Symptom
Washer will not power on at all; no lights or display, but outlet has power.
Main Power Supply Failure
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E1 |
Washer does not fill with water; after a few minutes it stops and displays E1.
|
Water Inlet Timeout / No Fill | View Details |
| E10 |
Washer displays E10 and will not start or stops shortly after starting.
|
Communication Error Between Main PCB and Inverter/Display | View Details |
| E11 |
Washer shows E11 and the door remains locked at the end of the cycle.
|
Door Unlock Failure | View Details |
| E12 |
Washer displays E12 and may stop heating or show erratic temperature behavior.
|
NTC Temperature Sensor Fault | View Details |
| E13 |
Washer shows E13 and may stop with water remaining in the tub or leak detected.
|
Leakage / Floor Pan Float Switch Activated | View Details |
| E2 |
Washer does not drain water; drum remains full and E2 is displayed.
|
Drain Timeout / No Drain | View Details |
| E21 |
Front-load Little Swan washer shows E21 and will not drain or spin.
|
Drain Pump Blocked / Slow Drain | View Details |
| E23 |
Washer displays E23 and may stop mid-cycle with water in the tub.
|
Drain Pump Triac / Control Fault | View Details |
| E3 |
Washer drum spins abnormally fast or slow, or stops unexpectedly during spin and shows E3.
|
Motor Tachometer / Speed Sensor Error | View Details |
| E30 |
Washer shows E30 and will not start; door may not lock properly.
|
Door Lock Circuit Error | View Details |
| E31 |
Washer displays E31 and water level reading is unstable or incorrect.
|
Pressure Sensor Calibration / Signal Error | View Details |
| E32 |
Washer shows E32 and may not spin or may stop with water in the drum.
|
Unbalanced Detection / Spin Protection Error | View Details |
| E4 |
Washer vibrates excessively or refuses to spin and displays E4.
|
Unbalanced Load / Vibration Protection | View Details |
| E40 |
Washer displays E40 and will not start; door symbol may flash.
|
Door Not Properly Closed | View Details |
| E41 |
Washer shows E41 even though the door appears closed.
|
Door Open Signal Error | View Details |
| E5 |
Washer door does not lock at the start of a cycle and E5 is displayed.
|
Door Lock Failure | View Details |
| E51 |
Washer displays E51 and will not spin or wash; motor does not run.
|
Motor Power Triac / Drive Circuit Error | View Details |
| E52 |
Washer shows E52; drum may start then stop repeatedly.
|
No Motor Tachometer Signal | View Details |
| E6 |
Washer stops mid-cycle and displays E6; drum may not rotate properly.
|
Motor Drive Fault / Overload | View Details |
| E60 |
Washer displays E60 and will not heat water or stops during heating phase.
|
General Heating System Error | View Details |
| E7 |
Washer displays E7 and may not start or may stop unexpectedly; water level seems incorrect.
|
Water Level Sensor (Pressure Switch) Error | View Details |
| E8 |
Washer displays E8 and may not heat water or may stop during wash.
|
Water Heating Fault | View Details |
| E9 |
Washer shows E9 and may leak or overfill; water level appears abnormal.
|
Overflow / Overfill Protection | View Details |
| E90 |
Washer shows E90 and is unresponsive or stuck at startup.
|
Configuration / EEPROM / Communication Error | View Details |
| – |
Top-load Little Swan washer does not agitate or spin, but fills and drains normally.
|
Clutch / Transmission or Drive System Failure (Top-Load) | View Details |
| – |
Washer display and buttons work, but cycle will not start when pressing Start/Pause.
|
Start Circuit / User Interface Logic Issue | View Details |
| – |
Washer does not spin clothes dry; clothes come out very wet, but machine completes the cycle.
|
Poor Spin Performance | View Details |
| – |
Washer does not take detergent or softener from the dispenser drawer.
|
Dispenser Drawer Water Flow Restriction | View Details |
| – |
Washer door will not open at the end of the cycle, but no error code is shown.
|
Door Stuck Locked After Cycle | View Details |
| – |
Washer emits a burning smell during operation.
|
Overheating Electrical or Mechanical Component | View Details |
| – |
Washer fills and drains but the drum does not rotate during wash or spin; no error code displayed.
|
Drive Motor Not Running | View Details |
| – |
Washer has a strong moldy or sewer-like odor inside the drum.
|
Biofilm and Detergent Residue Buildup | View Details |
| – |
Washer is very noisy during spin; grinding or rumbling sound from the drum area.
|
Tub Bearing and/or Spider Arm Failure | View Details |
| – |
Washer leaks water from the front during wash or spin.
|
Door Gasket (Bellows) Leak | View Details |
| – |
Washer leaks water from the rear or bottom during operation.
|
Internal Hose or Tub Seal Leak | View Details |
| – |
Washer leaves visible detergent or powder residue on clothes after washing.
|
Poor Rinsing / Detergent Dissolution Issue | View Details |
| – |
Washer makes a loud banging or knocking noise during spin.
|
Severe Out-of-Balance or Suspension Failure | View Details |
| – |
Washer stops mid-cycle and all lights go off, then comes back on later.
|
Intermittent Power Loss / Overheating Protection | View Details |
| – |
Washer takes much longer than the displayed time to finish a cycle.
|
Cycle Time Extension / Auto-Balancing and Heating Delays | View Details |
| – |
Washer vibrates excessively and "walks" across the floor during spin, but no error code appears.
|
Excessive Vibration / Poor Installation | View Details |
| – |
Washer will not power on at all; no lights or display, but outlet has power.
|
Main Power Supply Failure | View Details |
No matching codes found
Advertisements