Beko Carpet Cleaners Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E01
Carpet cleaner will not power on, display is blank, no lights or sounds when pressing the power button.
Main Power Supply / Control Board Protection Trip
E02
Carpet cleaner powers on but the suction motor does not start; display shows E02 and you may hear a relay click but no vacuum sound.
Suction Motor Circuit Fault / Overload Protection
E03
Solution pump does not spray water or detergent onto the carpet; display shows E03 when the trigger is pressed.
Solution Pump / Spray Pump Failure
E04
Dirty water tank full indicator is on and E04 is displayed even when the recovery tank is empty; suction stops shortly after starting.
Dirty Water Tank Full Sensor Fault
E05
Brush roll does not rotate; display shows E05 and sometimes a brief attempt to start the brush before stopping.
Brush Motor Overload / Brush Roll Jam
E06
Carpet cleaner stops mid-operation and displays E06; unit may feel hot to the touch and will not restart immediately.
Thermal Overload / Overheating Protection
E07
Display shows E07 and the unit will not spray detergent; detergent indicator may flash even when the tank is full.
Detergent Tank Presence / Flow Sensor Error
E08
Unit displays E08 and shuts down when the handle is reclined or moved; may work briefly in upright position only.
Tilt / Position Sensor Fault
E09
Display shows E09 and the unit will not start; sometimes accompanied by a beeping sequence at power-on.
Internal Communication Error (PCB to Sensor/Module)
E10
Display shows E10 and the unit stops spraying; may occur after running with very hot water or in a warm environment.
Water Temperature / Overheat Sensor Error
E11
Display shows E11 and the unit will not run the brush or suction when the handle trigger is pressed.
Trigger Switch / User Input Fault
E12
Display shows E12 and the unit beeps when trying to start; often occurs after the unit has been tipped or stored incorrectly.
Internal Leak / Moisture Detection
E13
Display shows E13 and the brush speed is erratic or does not respond to speed settings.
Brush Motor Speed Feedback / Hall Sensor Fault
E14
Display shows E14 and the unit will not accept new settings; buttons may not respond or respond incorrectly.
User Interface / Keypad Fault
E15
Display shows E15 and the unit will not start; often associated with low or fluctuating mains voltage.
Input Voltage Out of Range
Symptom
Brush roll makes loud grinding or rattling noises during operation.
Brush Roll Bearing Wear / Foreign Object
Symptom
Carpet cleaner has weak suction and leaves carpets very wet after multiple passes.
Reduced Airflow / Suction Loss
Symptom
Carpet cleaner is leaking clean water from the bottom even when not in use.
Clean Water Tank or Valve Leak
Symptom
Carpet cleaner leaves a musty or unpleasant odor during use.
Microbial Growth in Tanks / Hoses
Symptom
Carpet cleaner leaves streaks or lines of dirt and detergent on the carpet.
Uneven Spray / Pickup Pattern
Symptom
Carpet cleaner vibrates excessively and is difficult to control during use.
Brush Imbalance / Floorhead Mechanical Vibration
Symptom
Carpet cleaner will not start unless the handle is held in a specific position.
Intermittent Handle / Tilt Switch Connection
Symptom
Carpet remains overly wet long after cleaning, even though suction seems normal.
Excessive Solution Application / Poor Extraction Balance
Symptom
Clean water tank is difficult to remove or install; it feels stuck or does not latch properly.
Tank Latch / Alignment Issue
Symptom
Detergent is not being mixed properly; carpets are either too soapy or not cleaned well despite correct settings.
Detergent Mixing / Dosing Fault
Symptom
Dirty water leaks from around the recovery tank area during use.
Dirty Water Tank Seal Failure
Symptom
Display or indicator lights flicker or go off briefly when the pump or brush starts.
Voltage Drop / Loose Connection
Symptom
No water or detergent sprays onto the carpet, but the pump motor can be heard running.
Spray Line Blockage / Airlock
Symptom
Trigger feels loose or does not spring back, and spray is intermittent.
Mechanical Trigger / Linkage Failure
Symptom
Unit does not pick up water when using the accessory hose and upholstery tool, but floor mode works.
Accessory Suction Path Blockage / Valve Issue
Symptom
Unit emits a burning smell during operation, sometimes accompanied by reduced performance.
Overheating Motor or Slipping Belt
Symptom
Unit is very loud compared to normal operation, with a high-pitched whine from the motor area.
Suction Motor Bearing Wear
Symptom
Unit powers on but none of the buttons respond; only a fixed light or logo is shown.
Frozen Control Board / UI Lockup
Symptom
Unit shuts off randomly during use and restarts after a short rest.
Thermal Cut-Out Cycling
Symptom
Unit trips the household circuit breaker or RCD when switched on.
Electrical Short / Earth Leakage
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E01 |
Carpet cleaner will not power on, display is blank, no lights or sounds when pressing the power button.
|
Main Power Supply / Control Board Protection Trip | View Details |
| E02 |
Carpet cleaner powers on but the suction motor does not start; display shows E02 and you may hear a relay click but no vacuum sound.
|
Suction Motor Circuit Fault / Overload Protection | View Details |
| E03 |
Solution pump does not spray water or detergent onto the carpet; display shows E03 when the trigger is pressed.
|
Solution Pump / Spray Pump Failure | View Details |
| E04 |
Dirty water tank full indicator is on and E04 is displayed even when the recovery tank is empty; suction stops shortly after starting.
|
Dirty Water Tank Full Sensor Fault | View Details |
| E05 |
Brush roll does not rotate; display shows E05 and sometimes a brief attempt to start the brush before stopping.
|
Brush Motor Overload / Brush Roll Jam | View Details |
| E06 |
Carpet cleaner stops mid-operation and displays E06; unit may feel hot to the touch and will not restart immediately.
|
Thermal Overload / Overheating Protection | View Details |
| E07 |
Display shows E07 and the unit will not spray detergent; detergent indicator may flash even when the tank is full.
|
Detergent Tank Presence / Flow Sensor Error | View Details |
| E08 |
Unit displays E08 and shuts down when the handle is reclined or moved; may work briefly in upright position only.
|
Tilt / Position Sensor Fault | View Details |
| E09 |
Display shows E09 and the unit will not start; sometimes accompanied by a beeping sequence at power-on.
|
Internal Communication Error (PCB to Sensor/Module) | View Details |
| E10 |
Display shows E10 and the unit stops spraying; may occur after running with very hot water or in a warm environment.
|
Water Temperature / Overheat Sensor Error | View Details |
| E11 |
Display shows E11 and the unit will not run the brush or suction when the handle trigger is pressed.
|
Trigger Switch / User Input Fault | View Details |
| E12 |
Display shows E12 and the unit beeps when trying to start; often occurs after the unit has been tipped or stored incorrectly.
|
Internal Leak / Moisture Detection | View Details |
| E13 |
Display shows E13 and the brush speed is erratic or does not respond to speed settings.
|
Brush Motor Speed Feedback / Hall Sensor Fault | View Details |
| E14 |
Display shows E14 and the unit will not accept new settings; buttons may not respond or respond incorrectly.
|
User Interface / Keypad Fault | View Details |
| E15 |
Display shows E15 and the unit will not start; often associated with low or fluctuating mains voltage.
|
Input Voltage Out of Range | View Details |
| – |
Brush roll makes loud grinding or rattling noises during operation.
|
Brush Roll Bearing Wear / Foreign Object | View Details |
| – |
Carpet cleaner has weak suction and leaves carpets very wet after multiple passes.
|
Reduced Airflow / Suction Loss | View Details |
| – |
Carpet cleaner is leaking clean water from the bottom even when not in use.
|
Clean Water Tank or Valve Leak | View Details |
| – |
Carpet cleaner leaves a musty or unpleasant odor during use.
|
Microbial Growth in Tanks / Hoses | View Details |
| – |
Carpet cleaner leaves streaks or lines of dirt and detergent on the carpet.
|
Uneven Spray / Pickup Pattern | View Details |
| – |
Carpet cleaner vibrates excessively and is difficult to control during use.
|
Brush Imbalance / Floorhead Mechanical Vibration | View Details |
| – |
Carpet cleaner will not start unless the handle is held in a specific position.
|
Intermittent Handle / Tilt Switch Connection | View Details |
| – |
Carpet remains overly wet long after cleaning, even though suction seems normal.
|
Excessive Solution Application / Poor Extraction Balance | View Details |
| – |
Clean water tank is difficult to remove or install; it feels stuck or does not latch properly.
|
Tank Latch / Alignment Issue | View Details |
| – |
Detergent is not being mixed properly; carpets are either too soapy or not cleaned well despite correct settings.
|
Detergent Mixing / Dosing Fault | View Details |
| – |
Dirty water leaks from around the recovery tank area during use.
|
Dirty Water Tank Seal Failure | View Details |
| – |
Display or indicator lights flicker or go off briefly when the pump or brush starts.
|
Voltage Drop / Loose Connection | View Details |
| – |
No water or detergent sprays onto the carpet, but the pump motor can be heard running.
|
Spray Line Blockage / Airlock | View Details |
| – |
Trigger feels loose or does not spring back, and spray is intermittent.
|
Mechanical Trigger / Linkage Failure | View Details |
| – |
Unit does not pick up water when using the accessory hose and upholstery tool, but floor mode works.
|
Accessory Suction Path Blockage / Valve Issue | View Details |
| – |
Unit emits a burning smell during operation, sometimes accompanied by reduced performance.
|
Overheating Motor or Slipping Belt | View Details |
| – |
Unit is very loud compared to normal operation, with a high-pitched whine from the motor area.
|
Suction Motor Bearing Wear | View Details |
| – |
Unit powers on but none of the buttons respond; only a fixed light or logo is shown.
|
Frozen Control Board / UI Lockup | View Details |
| – |
Unit shuts off randomly during use and restarts after a short rest.
|
Thermal Cut-Out Cycling | View Details |
| – |
Unit trips the household circuit breaker or RCD when switched on.
|
Electrical Short / Earth Leakage | View Details |
No matching codes found
Advertisements