Wolf Gourmet
Wolf Gourmet Multicookers Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E1
Multicooker beeps and displays E1 shortly after powering on; cooking cannot start.
Internal Temperature Sensor Open Circuit
E2
Multicooker displays E2 and will not start or prematurely stops a cooking program.
Internal Temperature Sensor Short Circuit
E3
E3 error appears during a pressure or slow-cook program; unit stops heating.
Overtemperature Protection Triggered at Heating Plate
E4
E4 error appears when trying to start a pressure-cooking program; cooker will not build pressure.
Lid Position or Pressure Sensor Fault
E5
E5 error appears during preheat or pressure build; unit stops heating and may beep repeatedly.
Overpressure or Steam Release System Fault
E6
E6 error appears immediately when plugging in or when starting any program; cooker does not heat.
Heating Element or Power Drive Circuit Fault
E7
E7 error appears and the display may flicker or reset; cooker may shut off unexpectedly.
Input Power or Voltage Detection Error
E8
E8 error appears during pressure cooking; unit may not reach or maintain set pressure.
Pressure Sensor Calibration or Range Error
E9
E9 error appears and the cooker will not start any program; display otherwise looks normal.
Internal Memory or Firmware Error
ERR
Generic "ERR" message appears on the display and the cooker will not start or complete programs.
General Control System Error
HOT
Display shows "HOT" and the cooker will not start a new program or quickly cancels it.
Excess Residual Temperature Detected
LID
Display shows a lid-related message (e.g., "LID" or flashing lid icon) and the cooker refuses to start pressure or certain programs.
Lid Not Detected or Improperly Closed
OVR
Display shows an overfill/overflow warning (e.g., "OVR" or similar) and cooking is interrupted.
Overfill or Boil-Over Detection
PRB
Display shows a probe-related message (e.g., "PRB" or flashing probe icon) and temperature probe modes do not work.
Food Temperature Probe Detection Error
Symptom
Burning smell or visible smoke from the multicooker during operation.
Overheating or Electrical Insulation Failure
Symptom
Condensation or water drips down the outside of the multicooker during or after cooking.
Condensation Management / Collector Issue
Symptom
Control panel buttons are unresponsive or require very hard presses to register.
Keypad / Touchpad Failure
Symptom
Display is dim, flickering, or segments are missing, but the cooker still heats.
Display Module or Backlight Failure
Symptom
Float valve does not rise during pressure cooking, or stays up after cooking is complete.
Float Valve Sticking
Symptom
Food is consistently undercooked or overcooked compared to recipe times, even when following Wolf Gourmet instructions.
Temperature or Pressure Calibration Drift
Symptom
Inner pot contents scorch or stick badly to the bottom during pressure or slow cooking.
Localized Overheating / Poor Stirring
Symptom
Inner pot is difficult to insert or remove; it scrapes against the housing or gets stuck.
Inner Pot Fitment / Deformation Issue
Symptom
Keep Warm function does not maintain temperature; food becomes cold or continues to cook vigorously.
Keep-Warm Temperature Control Fault
Symptom
Lid is stuck and will not open after cooking; float valve appears down but the lid will not rotate.
Mechanical Lid Lock Jam
Symptom
Lid will not lock or engage for pressure cooking; it spins freely or stops before the locked position.
Lid Lock Misalignment or Wear
Symptom
Multicooker does not power on at all; display is blank and no lights or sounds occur.
No Power / Dead Unit
Symptom
Multicooker heats but never reaches or holds pressure; steam constantly escapes from the lid area.
Pressure Leak / Cannot Build Pressure
Symptom
Multicooker makes loud clicking, popping, or buzzing noises during operation beyond normal relay clicks.
Abnormal Electrical or Mechanical Noise
Symptom
Multicooker powers on but will not start any cooking program; pressing Start does nothing or cancels immediately.
Start Circuit or Safety Interlock Inhibition
Symptom
Multicooker vibrates excessively or "walks" on the countertop during cooking, especially at high temperatures.
Excessive Vibration / Instability
Symptom
Rust spots or discoloration appear inside the stainless-steel inner pot.
Inner Pot Surface Corrosion / Pitting
Symptom
Silicone lid gasket is loose, stretched, or falls out of the lid groove easily.
Lid Gasket Wear / Deformation
Symptom
Steam or water leaks from around the lid handle or steam release valve during pressure cooking.
Steam Release Valve or Float Valve Leak
Symptom
Steam release knob is hard to turn or feels stuck between Vent and Seal positions.
Steam Release Valve Mechanical Binding
Symptom
Timer counts down but the multicooker does not heat; food remains uncooked.
Heating Element Not Energizing
Symptom
Unit frequently trips the household circuit breaker or GFCI when starting or during cooking.
Excessive Current Draw or Ground Fault
Symptom
Unusual chemical or plastic odor from the multicooker that persists after several uses.
Off-Gassing from New Components or Overheated Plastic
Symptom
Water or broth leaks from the base of the multicooker onto the countertop during or after cooking.
Internal Liquid Leak / Overflow into Housing
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E1 |
Multicooker beeps and displays E1 shortly after powering on; cooking cannot start.
|
Internal Temperature Sensor Open Circuit | View Details |
| E2 |
Multicooker displays E2 and will not start or prematurely stops a cooking program.
|
Internal Temperature Sensor Short Circuit | View Details |
| E3 |
E3 error appears during a pressure or slow-cook program; unit stops heating.
|
Overtemperature Protection Triggered at Heating Plate | View Details |
| E4 |
E4 error appears when trying to start a pressure-cooking program; cooker will not build pressure.
|
Lid Position or Pressure Sensor Fault | View Details |
| E5 |
E5 error appears during preheat or pressure build; unit stops heating and may beep repeatedly.
|
Overpressure or Steam Release System Fault | View Details |
| E6 |
E6 error appears immediately when plugging in or when starting any program; cooker does not heat.
|
Heating Element or Power Drive Circuit Fault | View Details |
| E7 |
E7 error appears and the display may flicker or reset; cooker may shut off unexpectedly.
|
Input Power or Voltage Detection Error | View Details |
| E8 |
E8 error appears during pressure cooking; unit may not reach or maintain set pressure.
|
Pressure Sensor Calibration or Range Error | View Details |
| E9 |
E9 error appears and the cooker will not start any program; display otherwise looks normal.
|
Internal Memory or Firmware Error | View Details |
| ERR |
Generic "ERR" message appears on the display and the cooker will not start or complete programs.
|
General Control System Error | View Details |
| HOT |
Display shows "HOT" and the cooker will not start a new program or quickly cancels it.
|
Excess Residual Temperature Detected | View Details |
| LID |
Display shows a lid-related message (e.g., "LID" or flashing lid icon) and the cooker refuses to start pressure or certain programs.
|
Lid Not Detected or Improperly Closed | View Details |
| OVR |
Display shows an overfill/overflow warning (e.g., "OVR" or similar) and cooking is interrupted.
|
Overfill or Boil-Over Detection | View Details |
| PRB |
Display shows a probe-related message (e.g., "PRB" or flashing probe icon) and temperature probe modes do not work.
|
Food Temperature Probe Detection Error | View Details |
| – |
Burning smell or visible smoke from the multicooker during operation.
|
Overheating or Electrical Insulation Failure | View Details |
| – |
Condensation or water drips down the outside of the multicooker during or after cooking.
|
Condensation Management / Collector Issue | View Details |
| – |
Control panel buttons are unresponsive or require very hard presses to register.
|
Keypad / Touchpad Failure | View Details |
| – |
Display is dim, flickering, or segments are missing, but the cooker still heats.
|
Display Module or Backlight Failure | View Details |
| – |
Float valve does not rise during pressure cooking, or stays up after cooking is complete.
|
Float Valve Sticking | View Details |
| – |
Food is consistently undercooked or overcooked compared to recipe times, even when following Wolf Gourmet instructions.
|
Temperature or Pressure Calibration Drift | View Details |
| – |
Inner pot contents scorch or stick badly to the bottom during pressure or slow cooking.
|
Localized Overheating / Poor Stirring | View Details |
| – |
Inner pot is difficult to insert or remove; it scrapes against the housing or gets stuck.
|
Inner Pot Fitment / Deformation Issue | View Details |
| – |
Keep Warm function does not maintain temperature; food becomes cold or continues to cook vigorously.
|
Keep-Warm Temperature Control Fault | View Details |
| – |
Lid is stuck and will not open after cooking; float valve appears down but the lid will not rotate.
|
Mechanical Lid Lock Jam | View Details |
| – |
Lid will not lock or engage for pressure cooking; it spins freely or stops before the locked position.
|
Lid Lock Misalignment or Wear | View Details |
| – |
Multicooker does not power on at all; display is blank and no lights or sounds occur.
|
No Power / Dead Unit | View Details |
| – |
Multicooker heats but never reaches or holds pressure; steam constantly escapes from the lid area.
|
Pressure Leak / Cannot Build Pressure | View Details |
| – |
Multicooker makes loud clicking, popping, or buzzing noises during operation beyond normal relay clicks.
|
Abnormal Electrical or Mechanical Noise | View Details |
| – |
Multicooker powers on but will not start any cooking program; pressing Start does nothing or cancels immediately.
|
Start Circuit or Safety Interlock Inhibition | View Details |
| – |
Multicooker vibrates excessively or "walks" on the countertop during cooking, especially at high temperatures.
|
Excessive Vibration / Instability | View Details |
| – |
Rust spots or discoloration appear inside the stainless-steel inner pot.
|
Inner Pot Surface Corrosion / Pitting | View Details |
| – |
Silicone lid gasket is loose, stretched, or falls out of the lid groove easily.
|
Lid Gasket Wear / Deformation | View Details |
| – |
Steam or water leaks from around the lid handle or steam release valve during pressure cooking.
|
Steam Release Valve or Float Valve Leak | View Details |
| – |
Steam release knob is hard to turn or feels stuck between Vent and Seal positions.
|
Steam Release Valve Mechanical Binding | View Details |
| – |
Timer counts down but the multicooker does not heat; food remains uncooked.
|
Heating Element Not Energizing | View Details |
| – |
Unit frequently trips the household circuit breaker or GFCI when starting or during cooking.
|
Excessive Current Draw or Ground Fault | View Details |
| – |
Unusual chemical or plastic odor from the multicooker that persists after several uses.
|
Off-Gassing from New Components or Overheated Plastic | View Details |
| – |
Water or broth leaks from the base of the multicooker onto the countertop during or after cooking.
|
Internal Liquid Leak / Overflow into Housing | View Details |
No matching codes found
Advertisements