Asko Washer-Dryer Combos Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E01
Washer-dryer combo will not start; display shows E01 shortly after pressing Start.
Door Lock Failure
E02
Washer-dryer combo does not fill with water; E02 appears on the display shortly after cycle start.
Water Inlet Fault
E03
Washer-dryer combo fails to drain water; cycle stops and E03 is displayed.
Drain Pump or Drainage Fault
E04
Washer-dryer combo overfills or shows E04 and stops with water remaining in the drum.
Overfill / Water Level Sensor Fault
E05
Washer-dryer combo stops heating water; wash cycles run cold and E05 appears.
Water Heating Circuit Fault
E06
Dryer function does not heat; clothes remain wet after drying cycle and E06 is displayed.
Dryer Heating Circuit Fault
E07
Washer-dryer combo drum does not rotate during wash or dry; E07 appears on display.
Drive Motor / Motor Control Fault
E08
Washer-dryer combo shows E08 and stops; often associated with unbalanced load or spin issues.
Unbalanced Load / Motor Speed Detection Fault
E09
Washer-dryer combo stops mid-cycle and displays E09; often related to overheating or electronics.
Electronics Overheat / Power Supply Fault
E10
Washer-dryer combo door will not unlock at end of cycle; E10 is displayed.
Door Unlock Fault
E11
Washer-dryer combo shows E11 and stops; often associated with water leakage detection.
Leakage / Anti-Flood System Activation
E12
Washer-dryer combo displays E12; drying performance is poor or cycle aborts.
Moisture Sensor / Drying Sensor Fault
E13
Washer-dryer combo shows E13; often associated with communication issues between control boards (if separate motor or UI board).
Communication Error Between Control Modules
E20
Washer-dryer combo shows E20; typically related to low water level or fill timeout in certain Asko models.
Fill Timeout / Insufficient Water Level
E21
Washer-dryer combo shows E21; often associated with drain timeout or partial drainage.
Drain Timeout Fault
E30
Washer-dryer combo shows E30; often indicates a door or lock-related issue in some Asko firmware versions.
Door Status Error
E40
Washer-dryer combo shows E40; typically related to motor or tachometer issues in some Asko models.
Motor Tachometer / Speed Sensing Fault
E50
Washer-dryer combo shows E50; often a generic motor or drive fault in Asko error schemes.
General Motor Drive Fault
E60
Washer-dryer combo shows E60; typically associated with heating system faults (wash or dry).
General Heating System Fault
E70
Washer-dryer combo shows E70; often indicates a temperature sensor (NTC) fault in some Asko models.
NTC Temperature Sensor Fault
E90
Washer-dryer combo shows E90; often a configuration or EEPROM error in Asko control boards.
Configuration / EEPROM Fault
Symptom
Detergent remains in the drawer after the wash cycle; poor rinsing.
Dispenser Drawer / Water Flow Issue
Symptom
Dryer function takes excessively long and clothes remain damp, but no error code is shown.
Poor Drying Performance
Symptom
Washer-dryer combo displays incorrect time remaining or frequently pauses and extends cycle time.
Load Sensing / Heating Inefficiency
Symptom
Washer-dryer combo door will not open at the end of the cycle, but no error code is displayed.
Door Interlock Stuck Closed
Symptom
Washer-dryer combo emits a burning smell during operation.
Overheating Component or Belt Slippage
Symptom
Washer-dryer combo fills and tumbles but will not spin; clothes remain very wet at end of cycle.
No Spin / Spin Refusal
Symptom
Washer-dryer combo has a persistent musty or moldy odor inside the drum.
Biofilm / Mold Build-Up in Drum and Hoses
Symptom
Washer-dryer combo leaves gray or black marks on clothes.
Contamination from Drum or Seal
Symptom
Washer-dryer combo makes loud banging or knocking noises during spin.
Excessive Vibration / Suspension Fault
Symptom
Washer-dryer combo powers on but will not start any cycle; Start button unresponsive, no error code.
User Interface / Control Lock or Program Logic Fault
Symptom
Washer-dryer combo produces a high-pitched squeal or grinding noise when spinning or tumbling.
Drum Bearing or Drive System Wear
Symptom
Washer-dryer combo trips the household circuit breaker or RCD during operation.
Electrical Short or Ground Fault
Symptom
Washer-dryer combo vibrates excessively and "walks" across the floor during spin.
Installation / Balance Issue
Symptom
Washer-dryer combo will not power on at all; no lights or display.
No Power / Dead Appliance
Symptom
Water leaks from the front of the washer-dryer combo during wash or rinse.
Front Door Seal / Gasket Leak
Symptom
Water leaks from the rear or bottom of the washer-dryer combo.
Internal Hose or Pump Leak
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E01 |
Washer-dryer combo will not start; display shows E01 shortly after pressing Start.
|
Door Lock Failure | View Details |
| E02 |
Washer-dryer combo does not fill with water; E02 appears on the display shortly after cycle start.
|
Water Inlet Fault | View Details |
| E03 |
Washer-dryer combo fails to drain water; cycle stops and E03 is displayed.
|
Drain Pump or Drainage Fault | View Details |
| E04 |
Washer-dryer combo overfills or shows E04 and stops with water remaining in the drum.
|
Overfill / Water Level Sensor Fault | View Details |
| E05 |
Washer-dryer combo stops heating water; wash cycles run cold and E05 appears.
|
Water Heating Circuit Fault | View Details |
| E06 |
Dryer function does not heat; clothes remain wet after drying cycle and E06 is displayed.
|
Dryer Heating Circuit Fault | View Details |
| E07 |
Washer-dryer combo drum does not rotate during wash or dry; E07 appears on display.
|
Drive Motor / Motor Control Fault | View Details |
| E08 |
Washer-dryer combo shows E08 and stops; often associated with unbalanced load or spin issues.
|
Unbalanced Load / Motor Speed Detection Fault | View Details |
| E09 |
Washer-dryer combo stops mid-cycle and displays E09; often related to overheating or electronics.
|
Electronics Overheat / Power Supply Fault | View Details |
| E10 |
Washer-dryer combo door will not unlock at end of cycle; E10 is displayed.
|
Door Unlock Fault | View Details |
| E11 |
Washer-dryer combo shows E11 and stops; often associated with water leakage detection.
|
Leakage / Anti-Flood System Activation | View Details |
| E12 |
Washer-dryer combo displays E12; drying performance is poor or cycle aborts.
|
Moisture Sensor / Drying Sensor Fault | View Details |
| E13 |
Washer-dryer combo shows E13; often associated with communication issues between control boards (if separate motor or UI board).
|
Communication Error Between Control Modules | View Details |
| E20 |
Washer-dryer combo shows E20; typically related to low water level or fill timeout in certain Asko models.
|
Fill Timeout / Insufficient Water Level | View Details |
| E21 |
Washer-dryer combo shows E21; often associated with drain timeout or partial drainage.
|
Drain Timeout Fault | View Details |
| E30 |
Washer-dryer combo shows E30; often indicates a door or lock-related issue in some Asko firmware versions.
|
Door Status Error | View Details |
| E40 |
Washer-dryer combo shows E40; typically related to motor or tachometer issues in some Asko models.
|
Motor Tachometer / Speed Sensing Fault | View Details |
| E50 |
Washer-dryer combo shows E50; often a generic motor or drive fault in Asko error schemes.
|
General Motor Drive Fault | View Details |
| E60 |
Washer-dryer combo shows E60; typically associated with heating system faults (wash or dry).
|
General Heating System Fault | View Details |
| E70 |
Washer-dryer combo shows E70; often indicates a temperature sensor (NTC) fault in some Asko models.
|
NTC Temperature Sensor Fault | View Details |
| E90 |
Washer-dryer combo shows E90; often a configuration or EEPROM error in Asko control boards.
|
Configuration / EEPROM Fault | View Details |
| – |
Detergent remains in the drawer after the wash cycle; poor rinsing.
|
Dispenser Drawer / Water Flow Issue | View Details |
| – |
Dryer function takes excessively long and clothes remain damp, but no error code is shown.
|
Poor Drying Performance | View Details |
| – |
Washer-dryer combo displays incorrect time remaining or frequently pauses and extends cycle time.
|
Load Sensing / Heating Inefficiency | View Details |
| – |
Washer-dryer combo door will not open at the end of the cycle, but no error code is displayed.
|
Door Interlock Stuck Closed | View Details |
| – |
Washer-dryer combo emits a burning smell during operation.
|
Overheating Component or Belt Slippage | View Details |
| – |
Washer-dryer combo fills and tumbles but will not spin; clothes remain very wet at end of cycle.
|
No Spin / Spin Refusal | View Details |
| – |
Washer-dryer combo has a persistent musty or moldy odor inside the drum.
|
Biofilm / Mold Build-Up in Drum and Hoses | View Details |
| – |
Washer-dryer combo leaves gray or black marks on clothes.
|
Contamination from Drum or Seal | View Details |
| – |
Washer-dryer combo makes loud banging or knocking noises during spin.
|
Excessive Vibration / Suspension Fault | View Details |
| – |
Washer-dryer combo powers on but will not start any cycle; Start button unresponsive, no error code.
|
User Interface / Control Lock or Program Logic Fault | View Details |
| – |
Washer-dryer combo produces a high-pitched squeal or grinding noise when spinning or tumbling.
|
Drum Bearing or Drive System Wear | View Details |
| – |
Washer-dryer combo trips the household circuit breaker or RCD during operation.
|
Electrical Short or Ground Fault | View Details |
| – |
Washer-dryer combo vibrates excessively and "walks" across the floor during spin.
|
Installation / Balance Issue | View Details |
| – |
Washer-dryer combo will not power on at all; no lights or display.
|
No Power / Dead Appliance | View Details |
| – |
Water leaks from the front of the washer-dryer combo during wash or rinse.
|
Front Door Seal / Gasket Leak | View Details |
| – |
Water leaks from the rear or bottom of the washer-dryer combo.
|
Internal Hose or Pump Leak | View Details |
No matching codes found
Advertisements