Vedette Dryers Error Codes

E01

Dryer will not start, display shows E01 immediately after pressing Start

Door Lock / Door Switch Fault

E02

Dryer stops shortly after start, E02 displayed, drum may not rotate

Motor Start Failure / Motor Circuit Fault

E03

Dryer stops mid-cycle, E03 displayed, clothes remain wet and cold

Heating Circuit Failure

E04

Dryer displays E04 and stops, often early in the cycle, sometimes with very hot drum

Overheating / Airflow Restriction

E05

Dryer shows E05, cycle ends quickly, clothes remain damp or cold

NTC Temperature Sensor Fault

E06

Dryer displays E06, drum does not rotate although motor hum may be heard

Drive Belt / Drum Rotation Fault

E07

Dryer shows E07 and stops, often accompanied by loud noise or difficulty starting rotation

Motor Overload / Motor Overheating

E08

Dryer displays E08, no heat, fan may run normally

Heater Relay / Power Supply to Heater Fault

E09

Dryer shows E09, will not start, sometimes after a power surge or lightning

Main Control Board Communication / Internal Error

E10

Dryer displays E10 and stops, often on Vedette condenser or heat pump dryers with water tank

Condensate Pump / Water Level Fault

E11

Dryer shows E11, often accompanied by beeping and no start

User Interface / Keypad Fault

E12

Dryer displays E12, cycle may start but stops unexpectedly, especially on sensor-dry programs

Moisture Sensor Circuit Fault

E13

Dryer shows E13, often on heat pump Vedette dryers, unit may stop and not restart until cooled

Heat Pump System / Compressor Fault

E14

Dryer displays E14, will not start or stops, sometimes with water in base tray (on condenser/heat pump models)

Anti-Flood / Leak Detection Fault

E15

Dryer shows E15, beeps, and does not respond to program selection

Control Panel Communication / EEPROM Error

E16

Dryer displays E16, drum light may work but motor and heater do not start

Door Locking / Safety Circuit Fault

E17

Dryer shows E17, often on models with reversible door or advanced safety features

Door Reversal / Door Position Sensor Fault

E18

Dryer displays E18, often with very long drying times and poor condensation on condenser/heat pump models

Airflow / Condenser Temperature Fault

Symptom

Dryer causes condensation or steam in the laundry room; room becomes very humid

Exhaust / Condenser Venting Problem

Symptom

Dryer display shows unusually long or short remaining time that does not match actual drying

Sensor Calibration / Load Detection Issue

Symptom

Dryer display works but buttons are unresponsive or respond intermittently

User Interface / Keypad Contact Issue

Symptom

Dryer door is difficult to open or close; scraping or grinding at the front

Front Panel / Drum Alignment Issue

Symptom

Dryer door will not stay closed or pops open during cycle

Door Latch / Hinge Wear

Symptom

Dryer drum does not turn, but you can hear the motor humming when Start is pressed

Seized Drum or Failed Start Capacitor

Symptom

Dryer drum light stays on even when the door is closed, or never comes on

Door Switch / Drum Light Circuit Fault

Symptom

Dryer emits a burning smell during operation

Overheating or Foreign Object on Heater

Symptom

Dryer heats but takes very long to dry; clothes are warm but still damp at end of cycle

Restricted Airflow / Inefficient Drying

Symptom

Dryer leaks water onto the floor during or after a cycle

Condensate Drainage / Tank Overflow

Symptom

Dryer makes a rattling or metallic clinking noise during operation

Foreign Objects in Drum or Blower

Symptom

Dryer makes loud banging or thumping noise, especially with small loads

Drum Imbalance / Worn Support Rollers

Symptom

Dryer makes loud squealing or screeching noise during operation

Worn Drum Support Components

Symptom

Dryer occasionally trips the household circuit breaker or RCD

Electrical Short or Ground Fault

Symptom

Dryer runs but clothes come out very wrinkled and overdried

Moisture Sensing / Program Selection Issue

Symptom

Dryer runs but does not heat; clothes come out cold and wet, no error code displayed

Heating System Failure (No-Code Condition)

Symptom

Dryer runs only on some programs; other programs will not start or end immediately

Program Logic / Sensor Dependency Issue

Symptom

Dryer stops mid-cycle and will not restart until it cools down

Overheating / Thermal Cut-Out Activation

Symptom

Dryer stops with water remaining in the condenser area or tank does not fill

Condensate Pump Not Moving Water

Symptom

Dryer vibrates excessively or moves across the floor during operation

Installation / Support Imbalance

Symptom

Dryer will not power on at all; no lights, no display, completely dead

Power Supply / Main Fuse Failure

Symptom

Dryer will not start at all; no drum movement, but lights or display may be on

Start Circuit / Control Lock Issue