Beko Ranges & Cooktops Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E01
Electric oven will not heat, display shows E01 shortly after a heating command is selected.
Oven Temperature Sensor (NTC) Circuit Fault
E02
Electric oven overheats, temperature runs away above set point, display shows E02 and heating stops.
Oven Overtemperature / Sensor Range Error
E03
Electric oven does not heat and fan may run continuously, display shows E03.
Oven Heating Circuit Fault (Element or Relay Failure)
E04
Electric oven display shows E04 and the cooling fan may run; oven may not start a new cycle.
Oven Cooling Fan or Overheat Thermostat Fault
E05
Electric oven display shows E05 and the interior light and controls may still work but heating is disabled.
Door Lock / Door Switch Fault (Pyrolytic or Safety Lock Models)
E06
Electric oven display shows E06 and touch controls may be unresponsive or erratic.
User Interface / Touch Control Panel Communication Fault
E07
Electric oven display shows E07 and the oven may shut down unexpectedly during use.
Power Supply / Low Voltage Error
E08
Induction cooktop zone does not heat and the display shows E08 when that zone is selected.
Induction Power Module Overtemperature or Cooling Fault
E09
Induction cooktop zone shows E09 and will not heat, other zones may work normally.
Induction Power Module / IGBT Fault
E10
Induction cooktop displays E10 and all zones may shut down.
Cooktop Overtemperature Protection Triggered
E11
Induction cooktop zone shows E11 and does not detect cookware properly.
Cookware Detection / Induction Coil Feedback Fault
E20
Gas cooktop electronic ignition does not work and the display or indicator shows E20 on some models with timers.
Ignition System Power or Control Fault
E21
Gas cooktop shows E21 or a fault indicator; one or more burners will not ignite even though others work.
Individual Burner Ignition / Electrode Fault
E22
Gas cooktop with flame failure devices shows E22 and gas supply to a burner is cut off shortly after ignition.
Flame Failure Device (Thermocouple) Fault
E30
Electric oven display shows E30 and the clock/timer may reset or behave erratically.
Clock / Timer Module Fault
E31
Electric oven display shows E31 and fan-assisted modes may not operate correctly.
Oven Fan Motor or Feedback Fault
E40
Induction cooktop shows E40 and all zones are disabled.
Configuration / Internal Communication Error
E50
Electric oven shows E50 and will not start a cooking program.
Door Open Detection / Door Switch Fault (Non-locking Models)
E60
Electric oven shows E60 and interior light and fan may work but heating is disabled.
Selector Switch / Function Switch Fault
E70
Electric oven shows E70 and temperature cannot be adjusted correctly.
Temperature Knob / Potentiometer Fault (Analogue Control Models)
Symptom
Control knobs on range are very stiff or difficult to turn.
Valve or Selector Mechanical Binding
Symptom
Cooktop glass-ceramic surface is cracked or shattered.
Glass Top Mechanical Damage
Symptom
Electric oven does not heat in any mode, but the clock and light work.
Main Oven Heating Circuit Failure
Symptom
Electric oven fan runs but there is no heat in fan-assisted mode.
Convection (Fan) Element Failure
Symptom
Electric oven heats but does not reach the set temperature or cooks unevenly.
Temperature Regulation / Sensor or Element Degradation
Symptom
Electric oven trips the circuit breaker or RCD when heating is started.
Earth Leakage / Short Circuit in Heating Circuit
Symptom
Gas burner clicks and sparks but will not light or lights only with a match.
Gas Flow / Burner Blockage Fault
Symptom
Gas burner flame is yellow, noisy, or lifting off the burner ports.
Incorrect Combustion / Air–Gas Mixture Fault
Symptom
Gas burner lights but goes out when the knob is released.
Flame Failure Safety Device Not Holding
Symptom
Gas burner will not ignite (no clicking sound, no spark) but gas is present when knob is turned.
Ignition System Failure – No Spark
Symptom
Gas cooktop ignites but keeps clicking even after the flame is established.
Continuous Ignition / Stuck Ignition Switch
Symptom
Induction cooktop does not power on at all (no lights or display).
Main Power Supply Failure
Symptom
Induction cooktop powers on but all zones show a pan symbol flashing and will not heat.
Cookware Detection / User Error or Sensor Fault
Symptom
Oven cooling fan runs continuously even when the oven is off and cool.
Cooling Fan Control / Stuck Thermostat or Relay
Symptom
Oven door glass is loose, rattling, or has condensation between panes.
Door Glass Assembly / Seal Failure
Symptom
Oven door will not close fully or sags on one side.
Door Hinge / Hinge Receiver Wear
Symptom
Oven light does not work, but oven heats normally.
Oven Lamp / Lamp Holder Fault
Symptom
Radiant electric cooktop zone does not heat, indicator light may still come on.
Radiant Heating Element Failure
Symptom
Radiant electric cooktop zone overheats or does not regulate properly (always on full power).
Energy Regulator / Infinite Switch Fault
Symptom
Range clock/timer loses time or resets randomly.
Clock / Timer Power Stability Issue
Symptom
Range control panel buttons are unresponsive or intermittent.
User Interface Keypad / Touch Panel Fault
Symptom
Strong burning smell or smoke from oven during normal cooking (not first use).
Grease / Food Residue Ignition or Electrical Overheating
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E01 |
Electric oven will not heat, display shows E01 shortly after a heating command is selected.
|
Oven Temperature Sensor (NTC) Circuit Fault | View Details |
| E02 |
Electric oven overheats, temperature runs away above set point, display shows E02 and heating stops.
|
Oven Overtemperature / Sensor Range Error | View Details |
| E03 |
Electric oven does not heat and fan may run continuously, display shows E03.
|
Oven Heating Circuit Fault (Element or Relay Failure) | View Details |
| E04 |
Electric oven display shows E04 and the cooling fan may run; oven may not start a new cycle.
|
Oven Cooling Fan or Overheat Thermostat Fault | View Details |
| E05 |
Electric oven display shows E05 and the interior light and controls may still work but heating is disabled.
|
Door Lock / Door Switch Fault (Pyrolytic or Safety Lock Models) | View Details |
| E06 |
Electric oven display shows E06 and touch controls may be unresponsive or erratic.
|
User Interface / Touch Control Panel Communication Fault | View Details |
| E07 |
Electric oven display shows E07 and the oven may shut down unexpectedly during use.
|
Power Supply / Low Voltage Error | View Details |
| E08 |
Induction cooktop zone does not heat and the display shows E08 when that zone is selected.
|
Induction Power Module Overtemperature or Cooling Fault | View Details |
| E09 |
Induction cooktop zone shows E09 and will not heat, other zones may work normally.
|
Induction Power Module / IGBT Fault | View Details |
| E10 |
Induction cooktop displays E10 and all zones may shut down.
|
Cooktop Overtemperature Protection Triggered | View Details |
| E11 |
Induction cooktop zone shows E11 and does not detect cookware properly.
|
Cookware Detection / Induction Coil Feedback Fault | View Details |
| E20 |
Gas cooktop electronic ignition does not work and the display or indicator shows E20 on some models with timers.
|
Ignition System Power or Control Fault | View Details |
| E21 |
Gas cooktop shows E21 or a fault indicator; one or more burners will not ignite even though others work.
|
Individual Burner Ignition / Electrode Fault | View Details |
| E22 |
Gas cooktop with flame failure devices shows E22 and gas supply to a burner is cut off shortly after ignition.
|
Flame Failure Device (Thermocouple) Fault | View Details |
| E30 |
Electric oven display shows E30 and the clock/timer may reset or behave erratically.
|
Clock / Timer Module Fault | View Details |
| E31 |
Electric oven display shows E31 and fan-assisted modes may not operate correctly.
|
Oven Fan Motor or Feedback Fault | View Details |
| E40 |
Induction cooktop shows E40 and all zones are disabled.
|
Configuration / Internal Communication Error | View Details |
| E50 |
Electric oven shows E50 and will not start a cooking program.
|
Door Open Detection / Door Switch Fault (Non-locking Models) | View Details |
| E60 |
Electric oven shows E60 and interior light and fan may work but heating is disabled.
|
Selector Switch / Function Switch Fault | View Details |
| E70 |
Electric oven shows E70 and temperature cannot be adjusted correctly.
|
Temperature Knob / Potentiometer Fault (Analogue Control Models) | View Details |
| – |
Control knobs on range are very stiff or difficult to turn.
|
Valve or Selector Mechanical Binding | View Details |
| – |
Cooktop glass-ceramic surface is cracked or shattered.
|
Glass Top Mechanical Damage | View Details |
| – |
Electric oven does not heat in any mode, but the clock and light work.
|
Main Oven Heating Circuit Failure | View Details |
| – |
Electric oven fan runs but there is no heat in fan-assisted mode.
|
Convection (Fan) Element Failure | View Details |
| – |
Electric oven heats but does not reach the set temperature or cooks unevenly.
|
Temperature Regulation / Sensor or Element Degradation | View Details |
| – |
Electric oven trips the circuit breaker or RCD when heating is started.
|
Earth Leakage / Short Circuit in Heating Circuit | View Details |
| – |
Gas burner clicks and sparks but will not light or lights only with a match.
|
Gas Flow / Burner Blockage Fault | View Details |
| – |
Gas burner flame is yellow, noisy, or lifting off the burner ports.
|
Incorrect Combustion / Air–Gas Mixture Fault | View Details |
| – |
Gas burner lights but goes out when the knob is released.
|
Flame Failure Safety Device Not Holding | View Details |
| – |
Gas burner will not ignite (no clicking sound, no spark) but gas is present when knob is turned.
|
Ignition System Failure – No Spark | View Details |
| – |
Gas cooktop ignites but keeps clicking even after the flame is established.
|
Continuous Ignition / Stuck Ignition Switch | View Details |
| – |
Induction cooktop does not power on at all (no lights or display).
|
Main Power Supply Failure | View Details |
| – |
Induction cooktop powers on but all zones show a pan symbol flashing and will not heat.
|
Cookware Detection / User Error or Sensor Fault | View Details |
| – |
Oven cooling fan runs continuously even when the oven is off and cool.
|
Cooling Fan Control / Stuck Thermostat or Relay | View Details |
| – |
Oven door glass is loose, rattling, or has condensation between panes.
|
Door Glass Assembly / Seal Failure | View Details |
| – |
Oven door will not close fully or sags on one side.
|
Door Hinge / Hinge Receiver Wear | View Details |
| – |
Oven light does not work, but oven heats normally.
|
Oven Lamp / Lamp Holder Fault | View Details |
| – |
Radiant electric cooktop zone does not heat, indicator light may still come on.
|
Radiant Heating Element Failure | View Details |
| – |
Radiant electric cooktop zone overheats or does not regulate properly (always on full power).
|
Energy Regulator / Infinite Switch Fault | View Details |
| – |
Range clock/timer loses time or resets randomly.
|
Clock / Timer Power Stability Issue | View Details |
| – |
Range control panel buttons are unresponsive or intermittent.
|
User Interface Keypad / Touch Panel Fault | View Details |
| – |
Strong burning smell or smoke from oven during normal cooking (not first use).
|
Grease / Food Residue Ignition or Electrical Overheating | View Details |
No matching codes found
Advertisements