Beko Dishwashers Error Codes

E01

Dishwasher will not start a cycle, display shows E01 shortly after pressing Start.

Water Inlet Failure

E02

Dishwasher stops early in the cycle and displays E02, often without filling properly.

Water Level Sensing / Flow Meter Fault

E03

Dishwasher displays E03 and stops, often with water remaining in the tub.

Drain Pump or Drainage Fault

E04

Dishwasher shows E04, often accompanied by overfilling or water in the base tray.

Overfill / Overflow Protection Activated

E05

Dishwasher stops and displays E05, usually early in the wash cycle.

Turbidity Sensor / Water Quality Sensor Fault

E06

Dishwasher shows E06 and may not heat water or complete the cycle.

NTC Temperature Sensor Fault

E07

Dishwasher displays E07, often with poor or no water circulation.

Circulation Pump / Motor Fault

E08

Dishwasher shows E08 and may stop mid-cycle, often with insufficient water in the tub.

Low Water Level / Circulation Protection

E09

Dishwasher displays E09 and does not heat water; dishes come out cold and wet.

Heating Circuit Failure

E10

Dishwasher shows E10, often related to drying issues or fan operation.

Drying Fan / Ventilation Fault

E11

Dishwasher displays E11 and may not start or may stop shortly after starting.

Door Lock / Door Switch Fault

E12

Dishwasher shows E12, often associated with water softener or regeneration problems.

Water Softener / Regeneration Valve Fault

E13

Dishwasher displays E13, often linked to excessive water temperature.

Overtemperature / Heating Control Fault

E14

Dishwasher shows E14 and may not fill correctly or may overfill.

Flow Meter / Water Intake Measurement Fault

E15

Dishwasher displays E15 and will not start; often accompanied by the drain pump running continuously.

Anti-Flood System Activated (Base Tray Leak)

E16

Dishwasher shows E16, often related to water inlet valve or AquaStop malfunction.

AquaStop / Inlet Safety System Fault

E17

Dishwasher displays E17, often indicating a problem with water level or overfill.

Water Level Sensor / Pressure Switch Error

E18

Dishwasher shows E18 and may stop with water remaining or not filling correctly.

Water Supply Timeout / Insufficient Fill

E20

Dishwasher displays E20 and may not drain or may stop mid-cycle.

General Drainage / Pump Error

E21

Dishwasher shows E21, often associated with circulation pump issues.

Circulation Pump Blocked or Overloaded

E22

Dishwasher displays E22, often with standing water and dirty filters.

Filter Blockage / Sump Obstruction

E23

Dishwasher shows E23 and will not drain properly.

Drain Pump Electrical Fault

E24

Dishwasher displays E24 and may not drain; often occurs at the start or end of a cycle.

Drain Hose / Installation Fault

E25

Dishwasher shows E25 and will not drain; often accompanied by a humming noise from the base.

Drain Pump Blocked / Impeller Jammed

H2

Dishwasher displays H2 on some Beko models, often related to heating problems.

Heater or Temperature Sensor Error

H3

Dishwasher shows H3, often indicating an overheat or temperature control issue.

Overheating Protection Triggered

H4

Dishwasher displays H4, often associated with NTC sensor failure.

NTC Sensor Open/Short Circuit

H5

Dishwasher shows H5, often related to water level or pressure sensing.

Water Level Sensor / Pressure Switch Error

H6

Dishwasher displays H6, often indicating a circulation pump problem.

Circulation Pump Failure

Symptom

Detergent tablet or powder remains in the dispenser at the end of the cycle.

Detergent Dispenser / Spray Coverage Issue

Symptom

Dishes come out wet and not properly dried at the end of the cycle.

Poor Drying Performance

Symptom

Dishwasher does not power on at all; no lights or display.

No Mains Power / Control Board Not Energized

Symptom

Dishwasher door drops down quickly or will not stay in a partially open position.

Door Spring / Hinge Cable Failure

Symptom

Dishwasher door is difficult to close or does not latch properly.

Door Alignment / Latch Issue

Symptom

Dishwasher fills with water but does not wash; spray arms do not move and dishes remain dirty.

Circulation Pump Not Running

Symptom

Dishwasher leaks water from the bottom front of the door during a cycle.

Door Seal / Spray Pattern Leak

Symptom

Dishwasher leaks water from underneath or from the sides, not from the door.

Internal Hose / Pump / Tub Leak

Symptom

Dishwasher makes a high-pitched squealing or whining noise during operation.

Pump Bearing Wear / Cavitation

Symptom

Dishwasher makes loud grinding or rattling noises during wash or drain.

Foreign Object in Pump or Spray System

Symptom

Dishwasher powers on but will not start; Start button unresponsive or cycle will not begin.

User Interface / Door Interlock / Program Logic Fault

Symptom

Dishwasher runs but dishes are not cleaned properly; food remains and spray coverage is poor.

Poor Wash Performance / Hydraulic Circuit Restriction

Symptom

Dishwasher stops mid-cycle without any error code; lights may remain on.

Intermittent Power / Overheat / Control Logic Fault

Symptom

Dishwasher vibrates excessively or moves during operation.

Installation / Balancing Issue

Symptom

Rust spots appearing on cutlery or inside the dishwasher.

Corrosion / Material Degradation

Symptom

Unpleasant smell coming from the dishwasher, especially when opening the door.

Organic Buildup / Bacterial Growth

Symptom

Upper rack dishes remain dirty while lower rack is mostly clean.

Upper Spray Arm / Feed System Fault

Symptom

Water remains in the bottom of the dishwasher after the cycle finishes, but no error code is shown.

Partial Drain / Siphon or Installation Issue

Symptom

White film or cloudy residue on glasses and dishes after washing.

Limescale / Detergent Residue