Zanussi Dryers Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E10
Zanussi condenser or heat pump dryer will not start a cycle and displays E10 shortly after pressing start.
Water Inlet / Condenser Tank Filling Fault
E20
Zanussi dryer stops mid-cycle or will not start and shows E20 on the display.
Drain / Pumping Fault (Heat Pump or Condenser Dryer)
E21
Zanussi dryer displays E21 and may stop with water remaining in the sump or tank not filling properly.
Condensate Pump Blocked or Jammed
E30
Zanussi dryer will not start or stops and shows E30 on the display.
Door Lock / Door Interlock Fault
E31
Zanussi heat pump dryer shows E31 and may stop heating or terminate cycles prematurely.
Moisture Sensor Circuit Fault
E32
Zanussi dryer intermittently stops or misreads dryness level and displays E32.
Moisture Sensor Calibration / Signal Error
E40
Zanussi dryer will not start and shows E40 or flashes a door symbol.
Door Not Properly Closed / Door Switch Error
E50
Zanussi dryer attempts to start but drum does not turn, or stops during cycle and shows E50.
Motor / Motor Control Fault
E51
Zanussi dryer shows E51 and may trip the breaker or fail to start the motor.
Motor Triac Short Circuit on Control Board
E52
Zanussi dryer intermittently stops or fails to start the drum and displays E52.
Motor Tachometer Signal Fault
E60
Zanussi dryer runs but does not heat properly and shows E60 or a related E6x code.
General Heating System Fault
E61
Zanussi dryer heats very slowly or not at all and shows E61.
Insufficient Heating / Low Temperature Fault
E62
Zanussi dryer overheats, may stop mid-cycle, and displays E62.
Overheating / High Temperature Fault
E63
Zanussi dryer stops heating and shows E63.
Heater Safety Cut-Out / Thermal Fuse Tripped
E64
Zanussi dryer shows E64 and does not heat, or heats only briefly.
Heater Relay / Heater Circuit Fault
E70
Zanussi dryer displays E70 and may not heat correctly.
Temperature Sensor (NTC) Circuit Fault
E80
Zanussi dryer shows E80 and buttons or program selector may not respond correctly.
User Interface / Selector Switch Fault
E90
Zanussi dryer will not start and shows E90 or related E9x codes.
Communication Error Between Main PCB and User Interface
EF0
Zanussi dryer stops and shows EF0, sometimes accompanied by water under or inside the machine.
Leak / Anti-Flood System Activated
EH0
Zanussi dryer intermittently stops or will not start and shows EH0 or a power supply error.
Mains Power Supply / Voltage Fault
Symptom
Zanussi dryer control panel buttons are unresponsive or only some buttons work intermittently.
User Interface Button Failure
Symptom
Zanussi dryer display and lights flicker or reset during operation.
Intermittent Power / Electrical Connection Issue
Symptom
Zanussi dryer display shows symbols or text but is very dim or partially unreadable.
Display Backlight / LCD Failure
Symptom
Zanussi dryer display shows very short remaining time and ends the cycle quickly with clothes still wet, no error code.
Moisture Sensing / Auto-Dry Miscalibration
Symptom
Zanussi dryer door pops open during the cycle, stopping the machine.
Door Latch / Catch Failure
Symptom
Zanussi dryer door will not open at the end of the cycle, even though the machine has stopped.
Door Lock Stuck Closed
Symptom
Zanussi dryer drum does not turn, but the machine powers on and may heat.
Drum Drive Failure
Symptom
Zanussi dryer drum light works but the drum does not rotate and there is a humming noise.
Motor Start Failure
Symptom
Zanussi dryer emits a burning smell during operation.
Overheating or Foreign Object Contact
Symptom
Zanussi dryer emits a musty or unpleasant odor from the drum and exhaust.
Odor from Bacterial or Mold Growth / Residue Build-Up
Symptom
Zanussi dryer interior light does not work, but the dryer otherwise operates normally.
Drum Light Circuit Failure
Symptom
Zanussi dryer leaks water onto the floor during or after a cycle.
Water Leak from Condenser or Drain System
Symptom
Zanussi dryer makes loud banging or thumping noises during operation.
Drum Support / Suspension Fault
Symptom
Zanussi dryer powers on but will not start the cycle when the start button is pressed.
Start Circuit / Safety Interlock Issue
Symptom
Zanussi dryer produces a high-pitched squealing or squeaking noise while running.
Friction in Drum Support or Idler Pulley
Symptom
Zanussi dryer runs but clothes remain wet or very damp at the end of the cycle, no error code displayed.
Poor Drying Performance / Extended Drying Time
Symptom
Zanussi dryer runs but the drum turns intermittently, starting and stopping during the cycle.
Intermittent Motor Drive
Symptom
Zanussi dryer stops mid-cycle and all lights go off, then comes back on after cooling.
Thermal Overload / Overheating Protection
Symptom
Zanussi dryer vibrates excessively or moves across the floor during operation.
Excessive Vibration / Installation Issue
Symptom
Zanussi dryer will not start at all; no lights or display, completely dead.
No Power / Dead Appliance
Symptom
Zanussi heat pump dryer runs but there is little or no warm air from the drum, and drying is very slow, no error code.
Heat Pump System Underperformance
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E10 |
Zanussi condenser or heat pump dryer will not start a cycle and displays E10 shortly after pressing start.
|
Water Inlet / Condenser Tank Filling Fault | View Details |
| E20 |
Zanussi dryer stops mid-cycle or will not start and shows E20 on the display.
|
Drain / Pumping Fault (Heat Pump or Condenser Dryer) | View Details |
| E21 |
Zanussi dryer displays E21 and may stop with water remaining in the sump or tank not filling properly.
|
Condensate Pump Blocked or Jammed | View Details |
| E30 |
Zanussi dryer will not start or stops and shows E30 on the display.
|
Door Lock / Door Interlock Fault | View Details |
| E31 |
Zanussi heat pump dryer shows E31 and may stop heating or terminate cycles prematurely.
|
Moisture Sensor Circuit Fault | View Details |
| E32 |
Zanussi dryer intermittently stops or misreads dryness level and displays E32.
|
Moisture Sensor Calibration / Signal Error | View Details |
| E40 |
Zanussi dryer will not start and shows E40 or flashes a door symbol.
|
Door Not Properly Closed / Door Switch Error | View Details |
| E50 |
Zanussi dryer attempts to start but drum does not turn, or stops during cycle and shows E50.
|
Motor / Motor Control Fault | View Details |
| E51 |
Zanussi dryer shows E51 and may trip the breaker or fail to start the motor.
|
Motor Triac Short Circuit on Control Board | View Details |
| E52 |
Zanussi dryer intermittently stops or fails to start the drum and displays E52.
|
Motor Tachometer Signal Fault | View Details |
| E60 |
Zanussi dryer runs but does not heat properly and shows E60 or a related E6x code.
|
General Heating System Fault | View Details |
| E61 |
Zanussi dryer heats very slowly or not at all and shows E61.
|
Insufficient Heating / Low Temperature Fault | View Details |
| E62 |
Zanussi dryer overheats, may stop mid-cycle, and displays E62.
|
Overheating / High Temperature Fault | View Details |
| E63 |
Zanussi dryer stops heating and shows E63.
|
Heater Safety Cut-Out / Thermal Fuse Tripped | View Details |
| E64 |
Zanussi dryer shows E64 and does not heat, or heats only briefly.
|
Heater Relay / Heater Circuit Fault | View Details |
| E70 |
Zanussi dryer displays E70 and may not heat correctly.
|
Temperature Sensor (NTC) Circuit Fault | View Details |
| E80 |
Zanussi dryer shows E80 and buttons or program selector may not respond correctly.
|
User Interface / Selector Switch Fault | View Details |
| E90 |
Zanussi dryer will not start and shows E90 or related E9x codes.
|
Communication Error Between Main PCB and User Interface | View Details |
| EF0 |
Zanussi dryer stops and shows EF0, sometimes accompanied by water under or inside the machine.
|
Leak / Anti-Flood System Activated | View Details |
| EH0 |
Zanussi dryer intermittently stops or will not start and shows EH0 or a power supply error.
|
Mains Power Supply / Voltage Fault | View Details |
| – |
Zanussi dryer control panel buttons are unresponsive or only some buttons work intermittently.
|
User Interface Button Failure | View Details |
| – |
Zanussi dryer display and lights flicker or reset during operation.
|
Intermittent Power / Electrical Connection Issue | View Details |
| – |
Zanussi dryer display shows symbols or text but is very dim or partially unreadable.
|
Display Backlight / LCD Failure | View Details |
| – |
Zanussi dryer display shows very short remaining time and ends the cycle quickly with clothes still wet, no error code.
|
Moisture Sensing / Auto-Dry Miscalibration | View Details |
| – |
Zanussi dryer door pops open during the cycle, stopping the machine.
|
Door Latch / Catch Failure | View Details |
| – |
Zanussi dryer door will not open at the end of the cycle, even though the machine has stopped.
|
Door Lock Stuck Closed | View Details |
| – |
Zanussi dryer drum does not turn, but the machine powers on and may heat.
|
Drum Drive Failure | View Details |
| – |
Zanussi dryer drum light works but the drum does not rotate and there is a humming noise.
|
Motor Start Failure | View Details |
| – |
Zanussi dryer emits a burning smell during operation.
|
Overheating or Foreign Object Contact | View Details |
| – |
Zanussi dryer emits a musty or unpleasant odor from the drum and exhaust.
|
Odor from Bacterial or Mold Growth / Residue Build-Up | View Details |
| – |
Zanussi dryer interior light does not work, but the dryer otherwise operates normally.
|
Drum Light Circuit Failure | View Details |
| – |
Zanussi dryer leaks water onto the floor during or after a cycle.
|
Water Leak from Condenser or Drain System | View Details |
| – |
Zanussi dryer makes loud banging or thumping noises during operation.
|
Drum Support / Suspension Fault | View Details |
| – |
Zanussi dryer powers on but will not start the cycle when the start button is pressed.
|
Start Circuit / Safety Interlock Issue | View Details |
| – |
Zanussi dryer produces a high-pitched squealing or squeaking noise while running.
|
Friction in Drum Support or Idler Pulley | View Details |
| – |
Zanussi dryer runs but clothes remain wet or very damp at the end of the cycle, no error code displayed.
|
Poor Drying Performance / Extended Drying Time | View Details |
| – |
Zanussi dryer runs but the drum turns intermittently, starting and stopping during the cycle.
|
Intermittent Motor Drive | View Details |
| – |
Zanussi dryer stops mid-cycle and all lights go off, then comes back on after cooling.
|
Thermal Overload / Overheating Protection | View Details |
| – |
Zanussi dryer vibrates excessively or moves across the floor during operation.
|
Excessive Vibration / Installation Issue | View Details |
| – |
Zanussi dryer will not start at all; no lights or display, completely dead.
|
No Power / Dead Appliance | View Details |
| – |
Zanussi heat pump dryer runs but there is little or no warm air from the drum, and drying is very slow, no error code.
|
Heat Pump System Underperformance | View Details |
No matching codes found
Advertisements