Baumatic Dishwashers Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E1
Dishwasher will not fill with water, cycle stops shortly after start and E1 is displayed.
Water Inlet Timeout / No Fill
E10
Dishwasher displays E10 and may not start or may stop shortly after filling.
Water Distribution / Water Matrix Fault
E11
Dishwasher shows E11 and may not start the wash phase.
Door Lock / Door Switch Fault
E12
Dishwasher displays E12 and may have poor drying performance.
Drying System / Fan Fault
E13
Dishwasher shows E13 and may stop with water remaining or unusual noises.
Drain Sensor / Pressure Sensor Fault
E14
Dishwasher displays E14 and may not start or may stop early in the cycle.
Control Board Communication / Internal Error
E15
Dishwasher shows E15 and may not start; sometimes accompanied by beeping.
Water Hardness / Regeneration System Fault
E16
Dishwasher displays E16 and may not fill correctly or may overfill.
Inlet Valve / Flow Control Error
E17
Dishwasher shows E17 and may stop with water in the base or tub.
Leakage / Overflow Detection
E18
Dishwasher displays E18 and may not drain fully or may leave water in the sump.
Partial Drain / Slow Drain Fault
E19
Dishwasher shows E19 and may not complete the program.
Detergent Dispenser / Dosing Fault
E2
Dishwasher stops mid-cycle and displays E2, often after attempting to drain.
Drain Timeout / No Drain
E20
Dishwasher displays E20 and may not start or may stop unexpectedly.
User Interface / Keypad Fault
E3
Dishwasher fills but does not heat the water; cycle may run long and end with E3.
Heating Circuit Failure
E4
Dishwasher displays E4 and may run the drain pump continuously; sometimes water is found in the base tray.
Anti-Flood / Overflow Protection Activated
E5
Dishwasher shows E5 and may stop during the wash or rinse phase.
Water Level / Overfill Error
E6
Dishwasher displays E6 and may not start or may stop shortly after starting.
Water Inlet Sensor / Flow Meter Fault
E7
Dishwasher shows E7 and may not heat or may stop during drying.
Temperature Sensor (NTC) Fault
E8
Dishwasher displays E8 and may stop during wash with poor spray performance.
Circulation Pump / Motor Fault
E9
Dishwasher shows E9 and may stop with water remaining in the tub or base.
Diverter Valve / Spray Distribution Fault
Symptom
Control panel buttons are unresponsive or respond intermittently.
Keypad / User Interface Failure
Symptom
Detergent tablet remains in the dispenser at the end of the cycle.
Detergent Dispenser Opening Fault
Symptom
Dishes are wet at the end of the cycle; poor drying performance.
Poor Drying / Condensation Issue
Symptom
Dishwasher does not power on at all; no lights or display.
No Power / Dead Appliance
Symptom
Dishwasher door drops down quickly or will not stay in the half-open position.
Door Hinge / Spring or Cable Failure
Symptom
Dishwasher fills with water but the spray arms do not rotate; dishes remain dirty.
No Wash / Circulation Failure
Symptom
Dishwasher interior light (if fitted) does not work, but machine otherwise operates normally.
Interior Light Failure
Symptom
Dishwasher leaks water from the front of the door during a cycle.
Door Seal / Over-foaming Leak
Symptom
Dishwasher leaks water from underneath the cabinet.
Base Leak / Internal Hose or Sump Leak
Symptom
Dishwasher makes a high-pitched whining noise during operation.
Worn Pump Bearings or Cavitation
Symptom
Dishwasher makes loud grinding or rattling noises during wash.
Foreign Object in Pump or Spray Arm Interference
Symptom
Dishwasher powers on but will not start the cycle when Start is pressed.
Start Inhibit / Door or Program Not Accepted
Symptom
Dishwasher runs but dishes come out dirty or with food residues.
Poor Cleaning Performance
Symptom
Dishwasher stops mid-cycle without any error code; lights may remain on.
Intermittent Power or Overheat Protection
Symptom
Dishwasher trips the household circuit breaker or RCD during operation.
Electrical Short or Earth Leakage
Symptom
Dishwasher vibrates excessively or moves during operation.
Excessive Vibration / Poor Installation
Symptom
Rinse aid is not dispensing; dishes have water spots and streaks.
Rinse Aid Dispenser Fault
Symptom
Rust spots appearing on cutlery or inside the dishwasher tub.
Corrosion / Rust Contamination
Symptom
Unpleasant odour coming from the dishwasher, especially when opened after being idle.
Odour / Bacterial Growth
Symptom
Water remains in the bottom of the dishwasher after the cycle completes.
Standing Water / Incomplete Drain
Symptom
White film or cloudy deposits on glassware and dishes.
Limescale / Detergent Residue
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E1 |
Dishwasher will not fill with water, cycle stops shortly after start and E1 is displayed.
|
Water Inlet Timeout / No Fill | View Details |
| E10 |
Dishwasher displays E10 and may not start or may stop shortly after filling.
|
Water Distribution / Water Matrix Fault | View Details |
| E11 |
Dishwasher shows E11 and may not start the wash phase.
|
Door Lock / Door Switch Fault | View Details |
| E12 |
Dishwasher displays E12 and may have poor drying performance.
|
Drying System / Fan Fault | View Details |
| E13 |
Dishwasher shows E13 and may stop with water remaining or unusual noises.
|
Drain Sensor / Pressure Sensor Fault | View Details |
| E14 |
Dishwasher displays E14 and may not start or may stop early in the cycle.
|
Control Board Communication / Internal Error | View Details |
| E15 |
Dishwasher shows E15 and may not start; sometimes accompanied by beeping.
|
Water Hardness / Regeneration System Fault | View Details |
| E16 |
Dishwasher displays E16 and may not fill correctly or may overfill.
|
Inlet Valve / Flow Control Error | View Details |
| E17 |
Dishwasher shows E17 and may stop with water in the base or tub.
|
Leakage / Overflow Detection | View Details |
| E18 |
Dishwasher displays E18 and may not drain fully or may leave water in the sump.
|
Partial Drain / Slow Drain Fault | View Details |
| E19 |
Dishwasher shows E19 and may not complete the program.
|
Detergent Dispenser / Dosing Fault | View Details |
| E2 |
Dishwasher stops mid-cycle and displays E2, often after attempting to drain.
|
Drain Timeout / No Drain | View Details |
| E20 |
Dishwasher displays E20 and may not start or may stop unexpectedly.
|
User Interface / Keypad Fault | View Details |
| E3 |
Dishwasher fills but does not heat the water; cycle may run long and end with E3.
|
Heating Circuit Failure | View Details |
| E4 |
Dishwasher displays E4 and may run the drain pump continuously; sometimes water is found in the base tray.
|
Anti-Flood / Overflow Protection Activated | View Details |
| E5 |
Dishwasher shows E5 and may stop during the wash or rinse phase.
|
Water Level / Overfill Error | View Details |
| E6 |
Dishwasher displays E6 and may not start or may stop shortly after starting.
|
Water Inlet Sensor / Flow Meter Fault | View Details |
| E7 |
Dishwasher shows E7 and may not heat or may stop during drying.
|
Temperature Sensor (NTC) Fault | View Details |
| E8 |
Dishwasher displays E8 and may stop during wash with poor spray performance.
|
Circulation Pump / Motor Fault | View Details |
| E9 |
Dishwasher shows E9 and may stop with water remaining in the tub or base.
|
Diverter Valve / Spray Distribution Fault | View Details |
| – |
Control panel buttons are unresponsive or respond intermittently.
|
Keypad / User Interface Failure | View Details |
| – |
Detergent tablet remains in the dispenser at the end of the cycle.
|
Detergent Dispenser Opening Fault | View Details |
| – |
Dishes are wet at the end of the cycle; poor drying performance.
|
Poor Drying / Condensation Issue | View Details |
| – |
Dishwasher does not power on at all; no lights or display.
|
No Power / Dead Appliance | View Details |
| – |
Dishwasher door drops down quickly or will not stay in the half-open position.
|
Door Hinge / Spring or Cable Failure | View Details |
| – |
Dishwasher fills with water but the spray arms do not rotate; dishes remain dirty.
|
No Wash / Circulation Failure | View Details |
| – |
Dishwasher interior light (if fitted) does not work, but machine otherwise operates normally.
|
Interior Light Failure | View Details |
| – |
Dishwasher leaks water from the front of the door during a cycle.
|
Door Seal / Over-foaming Leak | View Details |
| – |
Dishwasher leaks water from underneath the cabinet.
|
Base Leak / Internal Hose or Sump Leak | View Details |
| – |
Dishwasher makes a high-pitched whining noise during operation.
|
Worn Pump Bearings or Cavitation | View Details |
| – |
Dishwasher makes loud grinding or rattling noises during wash.
|
Foreign Object in Pump or Spray Arm Interference | View Details |
| – |
Dishwasher powers on but will not start the cycle when Start is pressed.
|
Start Inhibit / Door or Program Not Accepted | View Details |
| – |
Dishwasher runs but dishes come out dirty or with food residues.
|
Poor Cleaning Performance | View Details |
| – |
Dishwasher stops mid-cycle without any error code; lights may remain on.
|
Intermittent Power or Overheat Protection | View Details |
| – |
Dishwasher trips the household circuit breaker or RCD during operation.
|
Electrical Short or Earth Leakage | View Details |
| – |
Dishwasher vibrates excessively or moves during operation.
|
Excessive Vibration / Poor Installation | View Details |
| – |
Rinse aid is not dispensing; dishes have water spots and streaks.
|
Rinse Aid Dispenser Fault | View Details |
| – |
Rust spots appearing on cutlery or inside the dishwasher tub.
|
Corrosion / Rust Contamination | View Details |
| – |
Unpleasant odour coming from the dishwasher, especially when opened after being idle.
|
Odour / Bacterial Growth | View Details |
| – |
Water remains in the bottom of the dishwasher after the cycle completes.
|
Standing Water / Incomplete Drain | View Details |
| – |
White film or cloudy deposits on glassware and dishes.
|
Limescale / Detergent Residue | View Details |
No matching codes found
Advertisements