Beko Dryers Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E01
Dryer will not start; display shows E01 immediately after pressing Start/Pause.
Door Lock / Door Closed Detection Fault
E02
Dryer stops shortly after starting; display shows E02 and drum may not rotate.
Motor Start / Motor Triac Fault
E03
Dryer does not heat; cycle runs but clothes remain cold and wet; E03 appears on display.
Heating Circuit Fault (Vented Dryer)
E04
Dryer stops mid-cycle and shows E04; may be accompanied by overheating or very hot cabinet surfaces.
Overheating / High Temperature Protection Trip
E05
Dryer does not heat properly; cycle ends quickly or runs indefinitely; E05 displayed.
NTC Temperature Sensor Fault
E06
Dryer drum does not rotate; E06 appears shortly after attempting to start a cycle.
Drum Motor / Tachometer Feedback Fault
E07
Dryer stops and displays E07; may occur on condenser and heat pump Beko dryers when water is not draining from the condenser area.
Condensate Pump / Water Level Fault
E08
On heat pump Beko dryers, E08 appears and the dryer does not heat properly or stops early.
Heat Pump System / Compressor Fault
E09
Dryer shows E09 and will not start or stops shortly after starting; often related to power supply or control issues.
Main Control Board / Power Supply Fault
E10
Dryer displays E10 and may not respond to program selection or start commands.
User Interface / Communication Fault
E11
Dryer shows E11; often associated with humidity sensing or drying time issues.
Moisture Sensor / Humidity Detection Fault
E12
Dryer displays E12; may be related to reverse rotation or motor direction control issues.
Motor Direction / Relay Fault
E13
On some Beko condenser/heat pump dryers, E13 appears and the water tank symbol may flash.
Water Tank Full Detection Fault
E14
Dryer shows E14; often associated with fan or airflow monitoring on some models.
Blower Fan / Airflow Monitoring Fault
E15
Dryer displays E15 and may shut down unexpectedly; can be related to internal communication or sensor bus errors.
Internal Communication / Sensor Bus Fault
E16
Dryer shows E16; may be associated with door locking/unlocking sequence errors on some models.
Door Lock Release / Detection Error
E17
Dryer displays E17; often linked to overcurrent or short circuit detection in the motor or heater circuit.
Overcurrent / Short Circuit Protection Trip
E18
Dryer shows E18; may be associated with low voltage or mains frequency detection on some electronic models.
Mains Supply / Frequency Detection Fault
Symptom
Dryer control panel buttons are unresponsive or only some buttons work intermittently.
User Interface Keypad Fault
Symptom
Dryer display and lights flicker or reset during operation.
Intermittent Power / Loose Connection
Symptom
Dryer door pops open during the cycle, stopping the program.
Door Latch / Catch Failure
Symptom
Dryer door seal is torn or clothes get caught at the door opening.
Damaged Door Gasket / Front Felt Seal
Symptom
Dryer door will not open at the end of the cycle; door appears locked even though the machine is off.
Door Lock Stuck Closed
Symptom
Dryer drum does not turn, but you can hear the motor humming or a buzzing noise.
Drum Not Turning / Belt or Motor Start Issue
Symptom
Dryer drum light does not work, but the dryer otherwise operates normally.
Drum Light Failure
Symptom
Dryer emits a burning smell during operation, even if clothes appear normal.
Overheating or Foreign Object on Heater
Symptom
Dryer ends the cycle very quickly and clothes are still wet; often on automatic sensor programs.
Moisture Sensor Not Detecting Wet Laundry
Symptom
Dryer has a musty or moldy smell that transfers to clothes.
Odor from Damp Lint and Condensate
Symptom
Dryer leaks water onto the floor from the front or bottom (condenser/heat pump models).
Water Leakage from Condenser System
Symptom
Dryer makes a thumping or banging noise as the drum turns, especially with certain loads.
Load Imbalance or Flat-Spotted Rollers
Symptom
Dryer makes loud squealing or screeching noises while running.
Worn Drum Support Components
Symptom
Dryer powers on but will not start when Start/Pause is pressed; a beep may sound but nothing happens.
Start Inhibit / Safety Interlock Not Satisfied
Symptom
Dryer produces a low rumbling or grinding noise that gets worse over time.
Drum Bearing / Motor Bearing Wear
Symptom
Dryer runs but clothes come out very hot and sometimes slightly scorched or with a burnt smell.
Overheating / Thermostat Regulation Fault
Symptom
Dryer runs but does not heat; clothes remain cold and damp at the end of the cycle (no error code displayed).
Heating Failure Without Error
Symptom
Dryer runs continuously and does not stop on automatic programs; clothes become over-dried.
Moisture Sensor Always Detecting Wet Laundry
Symptom
Dryer stops after a few minutes and the cabinet feels very hot; after cooling, it will run again for a short time.
Thermal Cut-Out Tripping Due to Blocked Airflow
Symptom
Dryer stops mid-cycle and the water tank full indicator lights, but the tank is empty or nearly empty.
False Water Tank Full Indication
Symptom
Dryer takes too long to dry clothes; loads are still damp after the normal program completes.
Poor Drying Performance / Restricted Airflow
Symptom
Dryer vibrates excessively or moves across the floor during operation.
Excessive Vibration / Imbalance
Symptom
Dryer will not start at all; no lights or display, completely dead.
No Power / Dead Appliance
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E01 |
Dryer will not start; display shows E01 immediately after pressing Start/Pause.
|
Door Lock / Door Closed Detection Fault | View Details |
| E02 |
Dryer stops shortly after starting; display shows E02 and drum may not rotate.
|
Motor Start / Motor Triac Fault | View Details |
| E03 |
Dryer does not heat; cycle runs but clothes remain cold and wet; E03 appears on display.
|
Heating Circuit Fault (Vented Dryer) | View Details |
| E04 |
Dryer stops mid-cycle and shows E04; may be accompanied by overheating or very hot cabinet surfaces.
|
Overheating / High Temperature Protection Trip | View Details |
| E05 |
Dryer does not heat properly; cycle ends quickly or runs indefinitely; E05 displayed.
|
NTC Temperature Sensor Fault | View Details |
| E06 |
Dryer drum does not rotate; E06 appears shortly after attempting to start a cycle.
|
Drum Motor / Tachometer Feedback Fault | View Details |
| E07 |
Dryer stops and displays E07; may occur on condenser and heat pump Beko dryers when water is not draining from the condenser area.
|
Condensate Pump / Water Level Fault | View Details |
| E08 |
On heat pump Beko dryers, E08 appears and the dryer does not heat properly or stops early.
|
Heat Pump System / Compressor Fault | View Details |
| E09 |
Dryer shows E09 and will not start or stops shortly after starting; often related to power supply or control issues.
|
Main Control Board / Power Supply Fault | View Details |
| E10 |
Dryer displays E10 and may not respond to program selection or start commands.
|
User Interface / Communication Fault | View Details |
| E11 |
Dryer shows E11; often associated with humidity sensing or drying time issues.
|
Moisture Sensor / Humidity Detection Fault | View Details |
| E12 |
Dryer displays E12; may be related to reverse rotation or motor direction control issues.
|
Motor Direction / Relay Fault | View Details |
| E13 |
On some Beko condenser/heat pump dryers, E13 appears and the water tank symbol may flash.
|
Water Tank Full Detection Fault | View Details |
| E14 |
Dryer shows E14; often associated with fan or airflow monitoring on some models.
|
Blower Fan / Airflow Monitoring Fault | View Details |
| E15 |
Dryer displays E15 and may shut down unexpectedly; can be related to internal communication or sensor bus errors.
|
Internal Communication / Sensor Bus Fault | View Details |
| E16 |
Dryer shows E16; may be associated with door locking/unlocking sequence errors on some models.
|
Door Lock Release / Detection Error | View Details |
| E17 |
Dryer displays E17; often linked to overcurrent or short circuit detection in the motor or heater circuit.
|
Overcurrent / Short Circuit Protection Trip | View Details |
| E18 |
Dryer shows E18; may be associated with low voltage or mains frequency detection on some electronic models.
|
Mains Supply / Frequency Detection Fault | View Details |
| – |
Dryer control panel buttons are unresponsive or only some buttons work intermittently.
|
User Interface Keypad Fault | View Details |
| – |
Dryer display and lights flicker or reset during operation.
|
Intermittent Power / Loose Connection | View Details |
| – |
Dryer door pops open during the cycle, stopping the program.
|
Door Latch / Catch Failure | View Details |
| – |
Dryer door seal is torn or clothes get caught at the door opening.
|
Damaged Door Gasket / Front Felt Seal | View Details |
| – |
Dryer door will not open at the end of the cycle; door appears locked even though the machine is off.
|
Door Lock Stuck Closed | View Details |
| – |
Dryer drum does not turn, but you can hear the motor humming or a buzzing noise.
|
Drum Not Turning / Belt or Motor Start Issue | View Details |
| – |
Dryer drum light does not work, but the dryer otherwise operates normally.
|
Drum Light Failure | View Details |
| – |
Dryer emits a burning smell during operation, even if clothes appear normal.
|
Overheating or Foreign Object on Heater | View Details |
| – |
Dryer ends the cycle very quickly and clothes are still wet; often on automatic sensor programs.
|
Moisture Sensor Not Detecting Wet Laundry | View Details |
| – |
Dryer has a musty or moldy smell that transfers to clothes.
|
Odor from Damp Lint and Condensate | View Details |
| – |
Dryer leaks water onto the floor from the front or bottom (condenser/heat pump models).
|
Water Leakage from Condenser System | View Details |
| – |
Dryer makes a thumping or banging noise as the drum turns, especially with certain loads.
|
Load Imbalance or Flat-Spotted Rollers | View Details |
| – |
Dryer makes loud squealing or screeching noises while running.
|
Worn Drum Support Components | View Details |
| – |
Dryer powers on but will not start when Start/Pause is pressed; a beep may sound but nothing happens.
|
Start Inhibit / Safety Interlock Not Satisfied | View Details |
| – |
Dryer produces a low rumbling or grinding noise that gets worse over time.
|
Drum Bearing / Motor Bearing Wear | View Details |
| – |
Dryer runs but clothes come out very hot and sometimes slightly scorched or with a burnt smell.
|
Overheating / Thermostat Regulation Fault | View Details |
| – |
Dryer runs but does not heat; clothes remain cold and damp at the end of the cycle (no error code displayed).
|
Heating Failure Without Error | View Details |
| – |
Dryer runs continuously and does not stop on automatic programs; clothes become over-dried.
|
Moisture Sensor Always Detecting Wet Laundry | View Details |
| – |
Dryer stops after a few minutes and the cabinet feels very hot; after cooling, it will run again for a short time.
|
Thermal Cut-Out Tripping Due to Blocked Airflow | View Details |
| – |
Dryer stops mid-cycle and the water tank full indicator lights, but the tank is empty or nearly empty.
|
False Water Tank Full Indication | View Details |
| – |
Dryer takes too long to dry clothes; loads are still damp after the normal program completes.
|
Poor Drying Performance / Restricted Airflow | View Details |
| – |
Dryer vibrates excessively or moves across the floor during operation.
|
Excessive Vibration / Imbalance | View Details |
| – |
Dryer will not start at all; no lights or display, completely dead.
|
No Power / Dead Appliance | View Details |
No matching codes found
Advertisements