Electrolux Garbage Disposals Error Codes

E01

Garbage disposal will not power on at all; no humming, no sound, wall switch appears to do nothing.

Primary Power Supply Interruption

E02

Garbage disposal hums when switched on but the grinding plate does not spin; unit may shut off after a few seconds.

Impeller Plate Jam / Rotor Locked

E03

Disposal runs but water backs up into the sink or drains very slowly; grinding seems normal but sink does not clear.

Discharge / Drain Outlet Obstruction

E04

Newly installed Electrolux disposal runs but water and food back up into the sink or dishwasher immediately.

Dishwasher Knockout Plug Not Removed / Installation Drain Blockage

E05

Disposal trips the reset button or circuit breaker frequently during normal use.

Overcurrent / Overload Condition

E06

Disposal runs but makes a loud metallic grinding or rattling noise, even with no food present.

Foreign Object in Grinding Chamber

E07

Disposal vibrates excessively and causes the sink or countertop to shake during operation.

Imbalance / Mounting System Looseness

E08

Water leaks from the top of the disposal where it meets the sink, especially when the sink is full.

Sink Flange Seal Failure

E09

Water leaks from the side of the disposal where the dishwasher drain hose connects.

Dishwasher Inlet Connection Leak

E10

Water leaks from the very bottom of the disposal housing, even when the unit is off but the sink is in use.

Internal Seal / Motor Housing Leak

E11

Disposal turns on by itself intermittently or will not turn off even when the wall switch is off.

Control / Switch Circuit Fault

E12

Disposal emits a burning smell or visible smoke when operated; may shut off quickly.

Motor Overheating / Winding Failure

E13

Disposal makes a low humming sound but then shuts off immediately, even with no visible jam.

Motor Start Failure

E14

Disposal runs but does not grind food effectively; large particles remain and are not broken down.

Dull Grinding Components

E15

Disposal is extremely loud, with a harsh roaring or growling sound, even when not grinding hard items.

Worn Motor Bearings / Internal Mechanical Wear

E16

Disposal will not run unless the reset button is pressed each time before use.

Faulty Internal Overload / Thermal Protector

E17

Disposal operates, but water and food waste back up into the opposite sink bowl.

Improper Double-Bowl Drain Configuration / Partial Blockage

E18

Disposal splashes water and food particles back up into the sink opening during operation.

Splash Guard / Baffle Malfunction

E19

Disposal emits a persistent foul odor even after normal use and rinsing.

Organic Buildup in Grinding Chamber and Drain

E20

Disposal is very slow to drain and water stands in the chamber after use, but there is no full blockage.

Partial Obstruction / Grease Buildup in Discharge Path

E21

Disposal will not start, but a faint click is heard from the unit when the switch is turned on.

Internal Relay / Control Module Failure

E22

Disposal runs but causes lights to flicker or dim significantly when starting.

High Inrush Current / Electrical Supply Issue

E23

Disposal stops abruptly during operation and will not restart until it cools down.

Thermal Overload Tripping Under Normal Load

E24

Disposal runs but water leaks from the side discharge connection where it joins the drain pipe.

Discharge Gasket / Slip Joint Leak

E25

Disposal will not operate when the air switch button is pressed (for models using an air switch), but unit runs if wired directly.

Air Switch / Pneumatic Control Failure

E26

Disposal runs only when the batch-feed stopper is held in a specific position; slight movement causes it to stop.

Batch-Feed Lid Sensor Misalignment

E27

Disposal causes a noticeable electrical shock or tingle when touching the sink or nearby metal surfaces during operation.

Grounding / Leakage Current Fault

E28

Disposal runs but the dishwasher does not drain through the disposal as expected.

Dishwasher Drain Flow Restriction at Disposal

E29

Disposal makes a chattering or clacking noise as if the impellers are loose, but it still grinds.

Loose or Worn Swivel Impellers

E30

Disposal will not turn on, but there is confirmed power at the unit and the reset button is not tripped.

Open Motor Circuit / Internal Fuse Failure

Symptom

Disposal causes cabinet moisture and mold due to slow, intermittent leaks at plumbing joints.

Chronic Low-Rate Plumbing Leaks

Symptom

Disposal intermittently fails to start; sometimes works after tapping the unit or toggling the switch several times.

Intermittent Electrical Connection / Failing Motor Brushes (if equipped)

Symptom

Disposal is completely dead after a power outage or surge; no hum, no reset response.

Surge Damage to Motor or Control

Symptom

Disposal works but there is a constant dripping sound inside the unit and minor rust is visible in the grinding chamber.

Surface Corrosion / Minor Chamber Wear

Symptom

Newly installed Electrolux disposal vibrates and leaks slightly at the sink flange immediately after installation.

Improper Initial Installation / Mounting Misalignment