Belling Washer-Dryer Combos Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E01
Washer-dryer will not start a cycle and may display a key/lock symbol; door will not lock when Start is pressed.
Door Lock Circuit Failure
E02
Washer-dryer does not fill with water; cycle stops shortly after start and E02 is displayed.
Water Inlet Timeout / Fill Fault
E03
Washer-dryer does not drain; water remains in drum and E03 is displayed.
Drain Pump Timeout
E04
Washer-dryer overfills or shows E04 shortly after starting; may attempt to drain continuously.
Overfill / Water Level Sensor Fault
E05
Washer-dryer stops during wash or rinse with E05; water may be cold or cycle time extended.
Water Heating Fault
E06
Washer-dryer stops mid-cycle or will not start spin; E06 displayed, sometimes with heavy loads.
Motor Tachometer / Speed Sensor Fault
E07
Washer-dryer fails to spin or shows E07; drum may attempt to turn then stop.
Motor Drive / Triac Fault
E08
Washer-dryer displays E08 and may stop during spin; sometimes associated with excessive vibration.
Unbalanced Load / Spin Protection Fault
E09
Washer-dryer stops and displays E09; may be accompanied by tripping of household breaker or no power to motor.
Motor Short Circuit / Overcurrent Fault
E10
Washer-dryer will not start drying cycle; E10 displayed when attempting to use dryer function.
Dryer Heater Circuit Fault
E11
Drying cycle runs but clothes remain wet or only slightly warm; E11 may appear mid-cycle.
Dryer Airflow / Overheat Fault
E12
Washer-dryer displays E12 and may stop during drying; drum may be hot and humid inside.
Dryer Condenser / Pump Fault (if fitted)
E13
Washer-dryer shows E13 and may stop; often associated with water detected in base tray or leak alarm.
Anti-Flood / Leak Detection Fault
E14
Washer-dryer displays E14; may not respond to program selection or buttons.
User Interface / Control Panel Communication Fault
E15
Washer-dryer shows E15 and may not start; often associated with incorrect mains voltage or power issues.
Power Supply / Voltage Fault
E16
Washer-dryer displays E16; may be related to door lock not releasing at end of cycle.
Door Unlock Fault
E17
Washer-dryer shows E17; often associated with water inlet sensor or flow meter issues on some models.
Water Flow Meter / Inlet Sensor Fault
E18
Washer-dryer displays E18; may be related to communication between main PCB and motor control (on inverter models).
Communication Error (Main PCB to Motor Inverter)
E19
Washer-dryer shows E19; may be associated with EEPROM or configuration memory issues.
Configuration / EEPROM Fault
E20
Washer-dryer displays E20; may be linked to generic motor or spin issues on some Belling platforms.
Generic Motor Fault
Symptom
Washer-dryer combo will not power on at all; no lights or display, but wall socket has power.
No Power / Dead Appliance
Symptom
Washer-dryer display and buttons are unresponsive or behave erratically.
User Interface Malfunction
Symptom
Washer-dryer does not dry effectively; clothes come out damp and cool, but no error code is shown.
Poor Drying Performance
Symptom
Washer-dryer door will not open at end of cycle, but no error code is shown.
Door Stuck Locked
Symptom
Washer-dryer drum does not spin at high speed; only slow tumbling occurs and clothes come out very wet.
No High-Speed Spin
Symptom
Washer-dryer emits a high-pitched squeal or screech during spin.
Belt or Pulley Noise
Symptom
Washer-dryer fills and drains but drum does not turn during wash or spin; no error code displayed.
Drum Not Turning / Motor Inoperative
Symptom
Washer-dryer has a burning smell during wash or spin cycles.
Overheating Component / Electrical Burning
Symptom
Washer-dryer has a persistent musty or mouldy smell inside the drum and on clothes.
Biofilm / Mould Build-Up
Symptom
Washer-dryer leaks water from the front during wash or rinse cycles.
Front Leak / Door Seal Failure
Symptom
Washer-dryer leaks water from the rear or underneath during fill or drain.
Rear/Bottom Leak
Symptom
Washer-dryer leaves clothes very wet after a completed wash-dry cycle.
Poor Spin or Drying Performance
Symptom
Washer-dryer leaves visible detergent or softener residues on clothes after washing.
Poor Rinsing / Detergent Dispensing Issue
Symptom
Washer-dryer makes loud banging or knocking noises during spin.
Excessive Vibration / Mechanical Impact
Symptom
Washer-dryer produces a grinding or rumbling noise, especially at high spin speeds.
Drum Bearing Failure
Symptom
Washer-dryer stops mid-cycle and does not progress, but display remains on and no code is shown.
Program Stalling / Sensor Feedback Issue
Symptom
Washer-dryer takes excessively long to complete cycles; time remaining may increase instead of decrease.
Extended Cycle Time / Heating or Sensor Issue
Symptom
Washer-dryer trips the household circuit breaker or RCD during operation.
Electrical Short or Earth Leakage
Symptom
Washer-dryer vibrates excessively and moves across the floor during spin, even when not heavily loaded.
Cabinet Instability / Suspension Wear
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E01 |
Washer-dryer will not start a cycle and may display a key/lock symbol; door will not lock when Start is pressed.
|
Door Lock Circuit Failure | View Details |
| E02 |
Washer-dryer does not fill with water; cycle stops shortly after start and E02 is displayed.
|
Water Inlet Timeout / Fill Fault | View Details |
| E03 |
Washer-dryer does not drain; water remains in drum and E03 is displayed.
|
Drain Pump Timeout | View Details |
| E04 |
Washer-dryer overfills or shows E04 shortly after starting; may attempt to drain continuously.
|
Overfill / Water Level Sensor Fault | View Details |
| E05 |
Washer-dryer stops during wash or rinse with E05; water may be cold or cycle time extended.
|
Water Heating Fault | View Details |
| E06 |
Washer-dryer stops mid-cycle or will not start spin; E06 displayed, sometimes with heavy loads.
|
Motor Tachometer / Speed Sensor Fault | View Details |
| E07 |
Washer-dryer fails to spin or shows E07; drum may attempt to turn then stop.
|
Motor Drive / Triac Fault | View Details |
| E08 |
Washer-dryer displays E08 and may stop during spin; sometimes associated with excessive vibration.
|
Unbalanced Load / Spin Protection Fault | View Details |
| E09 |
Washer-dryer stops and displays E09; may be accompanied by tripping of household breaker or no power to motor.
|
Motor Short Circuit / Overcurrent Fault | View Details |
| E10 |
Washer-dryer will not start drying cycle; E10 displayed when attempting to use dryer function.
|
Dryer Heater Circuit Fault | View Details |
| E11 |
Drying cycle runs but clothes remain wet or only slightly warm; E11 may appear mid-cycle.
|
Dryer Airflow / Overheat Fault | View Details |
| E12 |
Washer-dryer displays E12 and may stop during drying; drum may be hot and humid inside.
|
Dryer Condenser / Pump Fault (if fitted) | View Details |
| E13 |
Washer-dryer shows E13 and may stop; often associated with water detected in base tray or leak alarm.
|
Anti-Flood / Leak Detection Fault | View Details |
| E14 |
Washer-dryer displays E14; may not respond to program selection or buttons.
|
User Interface / Control Panel Communication Fault | View Details |
| E15 |
Washer-dryer shows E15 and may not start; often associated with incorrect mains voltage or power issues.
|
Power Supply / Voltage Fault | View Details |
| E16 |
Washer-dryer displays E16; may be related to door lock not releasing at end of cycle.
|
Door Unlock Fault | View Details |
| E17 |
Washer-dryer shows E17; often associated with water inlet sensor or flow meter issues on some models.
|
Water Flow Meter / Inlet Sensor Fault | View Details |
| E18 |
Washer-dryer displays E18; may be related to communication between main PCB and motor control (on inverter models).
|
Communication Error (Main PCB to Motor Inverter) | View Details |
| E19 |
Washer-dryer shows E19; may be associated with EEPROM or configuration memory issues.
|
Configuration / EEPROM Fault | View Details |
| E20 |
Washer-dryer displays E20; may be linked to generic motor or spin issues on some Belling platforms.
|
Generic Motor Fault | View Details |
| – |
Washer-dryer combo will not power on at all; no lights or display, but wall socket has power.
|
No Power / Dead Appliance | View Details |
| – |
Washer-dryer display and buttons are unresponsive or behave erratically.
|
User Interface Malfunction | View Details |
| – |
Washer-dryer does not dry effectively; clothes come out damp and cool, but no error code is shown.
|
Poor Drying Performance | View Details |
| – |
Washer-dryer door will not open at end of cycle, but no error code is shown.
|
Door Stuck Locked | View Details |
| – |
Washer-dryer drum does not spin at high speed; only slow tumbling occurs and clothes come out very wet.
|
No High-Speed Spin | View Details |
| – |
Washer-dryer emits a high-pitched squeal or screech during spin.
|
Belt or Pulley Noise | View Details |
| – |
Washer-dryer fills and drains but drum does not turn during wash or spin; no error code displayed.
|
Drum Not Turning / Motor Inoperative | View Details |
| – |
Washer-dryer has a burning smell during wash or spin cycles.
|
Overheating Component / Electrical Burning | View Details |
| – |
Washer-dryer has a persistent musty or mouldy smell inside the drum and on clothes.
|
Biofilm / Mould Build-Up | View Details |
| – |
Washer-dryer leaks water from the front during wash or rinse cycles.
|
Front Leak / Door Seal Failure | View Details |
| – |
Washer-dryer leaks water from the rear or underneath during fill or drain.
|
Rear/Bottom Leak | View Details |
| – |
Washer-dryer leaves clothes very wet after a completed wash-dry cycle.
|
Poor Spin or Drying Performance | View Details |
| – |
Washer-dryer leaves visible detergent or softener residues on clothes after washing.
|
Poor Rinsing / Detergent Dispensing Issue | View Details |
| – |
Washer-dryer makes loud banging or knocking noises during spin.
|
Excessive Vibration / Mechanical Impact | View Details |
| – |
Washer-dryer produces a grinding or rumbling noise, especially at high spin speeds.
|
Drum Bearing Failure | View Details |
| – |
Washer-dryer stops mid-cycle and does not progress, but display remains on and no code is shown.
|
Program Stalling / Sensor Feedback Issue | View Details |
| – |
Washer-dryer takes excessively long to complete cycles; time remaining may increase instead of decrease.
|
Extended Cycle Time / Heating or Sensor Issue | View Details |
| – |
Washer-dryer trips the household circuit breaker or RCD during operation.
|
Electrical Short or Earth Leakage | View Details |
| – |
Washer-dryer vibrates excessively and moves across the floor during spin, even when not heavily loaded.
|
Cabinet Instability / Suspension Wear | View Details |
No matching codes found
Advertisements