Brandt Washing Machines Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
D01
Washer will not start; display shows D01 and cycle will not begin when Start is pressed.
Door Lock Failure
D02
Washer stops mid-cycle or will not start spinning; display shows D02 and door remains locked.
Drain Timeout / Drain Pump Failure
D03
Washer fills but does not start drum movement; display shows D03 and cycle aborts.
Motor / Tachometer Fault
D04
Washer does not fill with water; display shows D04 shortly after cycle start.
Water Inlet Fault
D05
Washer stops during heating phase; display shows D05 and water remains cold.
Heating Circuit Fault
D06
Washer displays D06 and will not start; sometimes accompanied by beeping and no response to buttons.
Control Panel / User Interface Communication Error
D07
Washer shows D07 and drum does not spin; sometimes accompanied by humming from motor area.
Motor Blocked or Overload Protection
D08
Washer displays D08 and stops; often occurs during spin or high-speed operation.
Unbalanced Load / Spin Protection
D09
Washer shows D09 and will not start; door may not lock or unlock correctly.
Door Lock Circuit Error
D10
Washer displays D10 and stops; often associated with overfilling or water visible in the drum when it should be empty.
Water Level / Pressure Switch Fault
D11
Washer shows D11 and may stop with water remaining in the drum; sometimes accompanied by slow or no spin.
Drain / Water Level Inconsistency
D12
Washer displays D12 and does not heat; cycle may take unusually long.
Temperature Sensor (NTC) Error
D13
Washer shows D13 and stops; may occur when switching from wash to spin.
Program Sequence / Relay Error
D14
Washer displays D14 and does not start; often related to door not closing properly on certain Brandt models.
Door Not Properly Closed
D15
Washer shows D15 and may stop with water inside; sometimes occurs after power interruptions.
Memory / Program Corruption
E01
Washer does not start; display shows E01 and door symbol may flash.
Door Lock Error
E02
Washer does not fill or fills very slowly; display shows E02.
Water Fill Timeout
E03
Washer does not drain; display shows E03 and cycle stops with water in the drum.
Drain Fault
E04
Washer overfills or leaks from the door; display shows E04.
Overfill / Overflow Protection
E05
Washer does not heat; display shows E05 or cycle ends with cold water.
Heating Element Fault
E06
Washer shows E06 and drum does not rotate; may occur at start of wash or spin.
Motor Drive Fault
E07
Washer displays E07 and may stop during spin with excessive vibration.
Unbalanced Load / Motor Overspeed
E08
Washer shows E08 and may not spin; sometimes associated with water level issues.
Water Level / Spin Interlock Fault
E09
Washer displays E09 and stops; may be related to heating or motor on some Brandt models.
Power Component / Triac Error
E10
Washer shows E10 and does not fill correctly; may alternate between fill and drain.
Fill / Drain Conflict
E11
Washer displays E11 and may not lock the door or start.
Door Lock Communication Error
E12
Washer shows E12 and may stop during heating or rinsing.
NTC / Heating Control Error
E13
Washer displays E13 and may not spin or may stop unexpectedly.
Motor Tachometer / Speed Feedback Error
E21
Washer shows E21 and does not drain or spin properly.
Drain Pump / Blockage Error
E23
Washer displays E23 and may not drain; sometimes accompanied by tripping of household breaker.
Drain Pump Triac / PCB Fault
E31
Washer shows E31 and may not fill or may misread water level.
Pressure Sensor Calibration Error
Symptom
Washer does not take detergent or softener from the dispenser drawer properly.
Dispenser Drawer / Valve Flow Issue
Symptom
Washer door will not unlock at the end of the cycle; no error code displayed.
Door Lock Stuck Closed
Symptom
Washer drum does not turn at all, but the machine fills and drains normally and no error code is shown.
Drive Belt or Motor Failure
Symptom
Washer emits a burning smell or visible smoke during operation.
Electrical Overheating / Component Burnout
Symptom
Washer has a persistent bad odor inside the drum or on clothes.
Biofilm / Mold Build-up
Symptom
Washer intermittently trips the household circuit breaker or RCD during operation.
Electrical Leakage / Short Circuit
Symptom
Washer leaks water from the bottom rear or underneath the cabinet.
Internal Hose or Tub Seal Leak
Symptom
Washer leaks water from the front door area during wash or rinse.
Door Gasket (Boot Seal) Leak
Symptom
Washer leaves clothes very wet at the end of the cycle; spin seems weak but no error code is shown.
Poor Spin Performance
Symptom
Washer makes a loud banging or knocking noise during spin and may move across the floor.
Excessive Vibration / Suspension Failure
Symptom
Washer makes a very loud rumbling or roaring noise during spin.
Drum Bearing Failure
Symptom
Washer powers on but will not start a cycle; Start button unresponsive, no error code.
User Interface / Control Lock Issue
Symptom
Washer takes much longer than the displayed time to complete a cycle.
Cycle Time Extension / Heating or Drain Inefficiency
Symptom
Washer will not start at all; no lights or display, completely dead.
No Power / Main Supply Fault
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| D01 |
Washer will not start; display shows D01 and cycle will not begin when Start is pressed.
|
Door Lock Failure | View Details |
| D02 |
Washer stops mid-cycle or will not start spinning; display shows D02 and door remains locked.
|
Drain Timeout / Drain Pump Failure | View Details |
| D03 |
Washer fills but does not start drum movement; display shows D03 and cycle aborts.
|
Motor / Tachometer Fault | View Details |
| D04 |
Washer does not fill with water; display shows D04 shortly after cycle start.
|
Water Inlet Fault | View Details |
| D05 |
Washer stops during heating phase; display shows D05 and water remains cold.
|
Heating Circuit Fault | View Details |
| D06 |
Washer displays D06 and will not start; sometimes accompanied by beeping and no response to buttons.
|
Control Panel / User Interface Communication Error | View Details |
| D07 |
Washer shows D07 and drum does not spin; sometimes accompanied by humming from motor area.
|
Motor Blocked or Overload Protection | View Details |
| D08 |
Washer displays D08 and stops; often occurs during spin or high-speed operation.
|
Unbalanced Load / Spin Protection | View Details |
| D09 |
Washer shows D09 and will not start; door may not lock or unlock correctly.
|
Door Lock Circuit Error | View Details |
| D10 |
Washer displays D10 and stops; often associated with overfilling or water visible in the drum when it should be empty.
|
Water Level / Pressure Switch Fault | View Details |
| D11 |
Washer shows D11 and may stop with water remaining in the drum; sometimes accompanied by slow or no spin.
|
Drain / Water Level Inconsistency | View Details |
| D12 |
Washer displays D12 and does not heat; cycle may take unusually long.
|
Temperature Sensor (NTC) Error | View Details |
| D13 |
Washer shows D13 and stops; may occur when switching from wash to spin.
|
Program Sequence / Relay Error | View Details |
| D14 |
Washer displays D14 and does not start; often related to door not closing properly on certain Brandt models.
|
Door Not Properly Closed | View Details |
| D15 |
Washer shows D15 and may stop with water inside; sometimes occurs after power interruptions.
|
Memory / Program Corruption | View Details |
| E01 |
Washer does not start; display shows E01 and door symbol may flash.
|
Door Lock Error | View Details |
| E02 |
Washer does not fill or fills very slowly; display shows E02.
|
Water Fill Timeout | View Details |
| E03 |
Washer does not drain; display shows E03 and cycle stops with water in the drum.
|
Drain Fault | View Details |
| E04 |
Washer overfills or leaks from the door; display shows E04.
|
Overfill / Overflow Protection | View Details |
| E05 |
Washer does not heat; display shows E05 or cycle ends with cold water.
|
Heating Element Fault | View Details |
| E06 |
Washer shows E06 and drum does not rotate; may occur at start of wash or spin.
|
Motor Drive Fault | View Details |
| E07 |
Washer displays E07 and may stop during spin with excessive vibration.
|
Unbalanced Load / Motor Overspeed | View Details |
| E08 |
Washer shows E08 and may not spin; sometimes associated with water level issues.
|
Water Level / Spin Interlock Fault | View Details |
| E09 |
Washer displays E09 and stops; may be related to heating or motor on some Brandt models.
|
Power Component / Triac Error | View Details |
| E10 |
Washer shows E10 and does not fill correctly; may alternate between fill and drain.
|
Fill / Drain Conflict | View Details |
| E11 |
Washer displays E11 and may not lock the door or start.
|
Door Lock Communication Error | View Details |
| E12 |
Washer shows E12 and may stop during heating or rinsing.
|
NTC / Heating Control Error | View Details |
| E13 |
Washer displays E13 and may not spin or may stop unexpectedly.
|
Motor Tachometer / Speed Feedback Error | View Details |
| E21 |
Washer shows E21 and does not drain or spin properly.
|
Drain Pump / Blockage Error | View Details |
| E23 |
Washer displays E23 and may not drain; sometimes accompanied by tripping of household breaker.
|
Drain Pump Triac / PCB Fault | View Details |
| E31 |
Washer shows E31 and may not fill or may misread water level.
|
Pressure Sensor Calibration Error | View Details |
| – |
Washer does not take detergent or softener from the dispenser drawer properly.
|
Dispenser Drawer / Valve Flow Issue | View Details |
| – |
Washer door will not unlock at the end of the cycle; no error code displayed.
|
Door Lock Stuck Closed | View Details |
| – |
Washer drum does not turn at all, but the machine fills and drains normally and no error code is shown.
|
Drive Belt or Motor Failure | View Details |
| – |
Washer emits a burning smell or visible smoke during operation.
|
Electrical Overheating / Component Burnout | View Details |
| – |
Washer has a persistent bad odor inside the drum or on clothes.
|
Biofilm / Mold Build-up | View Details |
| – |
Washer intermittently trips the household circuit breaker or RCD during operation.
|
Electrical Leakage / Short Circuit | View Details |
| – |
Washer leaks water from the bottom rear or underneath the cabinet.
|
Internal Hose or Tub Seal Leak | View Details |
| – |
Washer leaks water from the front door area during wash or rinse.
|
Door Gasket (Boot Seal) Leak | View Details |
| – |
Washer leaves clothes very wet at the end of the cycle; spin seems weak but no error code is shown.
|
Poor Spin Performance | View Details |
| – |
Washer makes a loud banging or knocking noise during spin and may move across the floor.
|
Excessive Vibration / Suspension Failure | View Details |
| – |
Washer makes a very loud rumbling or roaring noise during spin.
|
Drum Bearing Failure | View Details |
| – |
Washer powers on but will not start a cycle; Start button unresponsive, no error code.
|
User Interface / Control Lock Issue | View Details |
| – |
Washer takes much longer than the displayed time to complete a cycle.
|
Cycle Time Extension / Heating or Drain Inefficiency | View Details |
| – |
Washer will not start at all; no lights or display, completely dead.
|
No Power / Main Supply Fault | View Details |
No matching codes found
Advertisements