Casarte Washing Machines Error Codes

E1

Washer does not fill with water, cycle will not start, E1 displayed on Casarte washer

Water Inlet Timeout / No Fill

E10

Washer shows E10 and will not start or stops mid-cycle, often related to communication between boards

Communication Error Between Main PCB and Motor/Inverter PCB

E11

Washer displays E11 and does not start, often immediately after pressing Start

Door Not Closed / Door Switch Signal Error

E12

Washer shows E12 and may stop heating or abort cycle, often related to temperature sensing

NTC Temperature Sensor Error

E13

Washer displays E13 and may stop with water in drum, often related to drain or overflow sensor

Drain / Overflow Sensor Error

E2

Washer does not drain, water remains in drum, E2 displayed on Casarte washer

Drain Timeout / No Drain

E21

Washer shows E21 and stops, often during spin or drain, drum may not rotate correctly

Motor Tachometer / Speed Feedback Error

E22

Washer displays E22 and may not start or may stop unexpectedly, often related to door lock timing

Door Lock Timeout / Unlock Error

E3

Washer drum does not spin or spin is very weak, E3 displayed on Casarte washer

Motor Drive Fault / No Spin

E30

Washer shows E30 and will not start or stops, often related to power supply or internal voltage

Power Supply / Voltage Error

E31

Washer displays E31 and may not heat or may stop mid-cycle, often related to heater relay

Heater Relay / Triac Error

E32

Washer shows E32 and may not spin at high speed, often related to imbalance detection

Spin Imbalance Detection Error

E4

Washer displays E4 and stops during spin, drum vibrates excessively or cannot balance load

Unbalanced Load / Vibration Protection

E40

Washer displays E40 and will not start, often accompanied by beeping and door symbol

Door Open Detection Error

E41

Washer shows E41 and may lock the door but not start the cycle

Door Lock Circuit Error

E5

Washer does not heat water properly, cycle takes very long, E5 displayed on Casarte washer

Water Heating Fault

E50

Washer displays E50 and may not spin or wash, often related to motor drive

General Motor Error

E51

Washer shows E51 and stops, often during spin acceleration

Motor Overcurrent / Short Circuit

E6

Washer door will not lock or unlock, E6 displayed on Casarte washer

Door Lock / Interlock Failure

E60

Washer displays E60 and does not heat, or trips breaker when heating should start

Heating System General Error

E7

Washer overfills or shows E7 with water level error, water may be too high or too low

Water Level Sensor / Pressure Switch Fault

E70

Washer shows E70 and may not respond correctly to temperature settings

Temperature Sensor Circuit General Error

E8

Washer displays E8 and stops, often during wash or spin, may not start motor

Motor Overload / Overcurrent Protection

E9

Washer displays E9 and stops, often associated with water leakage or abnormal water level changes

Leakage / Overflow Protection

E90

Washer displays E90 and is unresponsive or stuck, often after power issues or firmware problems

Main Control Board Communication / Configuration Error

Symptom

Washer display flickers or resets during operation

Intermittent Power or Control Issue

Symptom

Washer does not dispense detergent or softener properly, residues remain in drawer

Detergent Dispenser Blockage

Symptom

Washer does not power on at all, no lights or display

No Power / Dead Appliance

Symptom

Washer door remains locked after cycle ends and no error code is shown

Door Lock Stuck Closed

Symptom

Washer drum does not turn during wash but can be turned by hand

Drive Failure Without Error Code

Symptom

Washer drum is very noisy when spinning, with rumbling or grinding sound

Drum Bearing Failure

Symptom

Washer emits a burning smell or electrical odor during operation

Overheating Electrical Component

Symptom

Washer emits a sewage or rotten smell from the drain hose or standpipe

Drain System Odor

Symptom

Washer fills and drains repeatedly without progressing in the cycle

Siphoning or Incorrect Drain Installation

Symptom

Washer has a strong moldy or musty odor inside the drum

Biofilm and Mold Build-Up

Symptom

Washer leaks water from the front door area during wash or spin

Door Gasket (Boot) Leak

Symptom

Washer leaks water from the rear or bottom during operation

Internal Hose or Pump Leak

Symptom

Washer leaves clothes soaking wet at the end of the cycle

Poor Spin / Incomplete Drain

Symptom

Washer makes loud banging or knocking noises during spin

Excessive Vibration / Suspension Failure

Symptom

Washer powers on but will not start any cycle when Start button is pressed

User Interface / Control Lock or Start Circuit Issue

Symptom

Washer produces excessive foam and may leak suds from the door or drawer

Over-Sudsing

Symptom

Washer takes much longer than the displayed time to complete a cycle

Extended Cycle Time / Heating or Balancing Issues

Symptom

Washer vibrates and moves across the floor during spin

Excessive Vibration / Installation Issue