Fagor Washing Machines Error Codes

E01

Washer will not start a cycle; display shows E01 and door does not lock

Door Lock / Interlock Failure

E02

Washer fills very slowly or not at all; display shows E02

Water Inlet / Fill Timeout

E03

Washer will not drain; cycle stops with water in drum and E03 on display

Drain Pump Timeout / Drain Failure

E04

Washer overfills or shows E04 shortly after starting; may attempt to drain immediately

Overfill / Water Level Sensor Error

E05

Washer does not heat water; cycle may be very long or stop with E05

Heating Circuit Failure

E06

Washer stops during spin or will not spin; E06 displayed

Motor / Tachometer Feedback Error

E07

Washer door will not unlock at end of cycle; E07 displayed

Door Unlock Failure

E08

Washer drum does not turn; E08 displayed shortly after start

Motor Start Failure

E09

Washer stops mid-cycle with E09; may trip household breaker in some cases

Heater Short / Power Supply Error

E10

Washer does not detect water level correctly; may stop with E10 or show erratic fill/drain behavior

Pressure Switch / Level Sensor Fault

E11

Washer fills and drains repeatedly without progressing; E11 displayed

Water Level Not Reached / Fill-Drain Loop

E12

Washer shows E12 and stops; often related to overheating or temperature sensing

NTC Temperature Sensor Error

E13

Washer leaks into base tray and stops with E13; may activate anti-flood protection

Leak Detected / Anti-Flood Activated

E14

Washer shows E14 and does not start; often related to door or safety circuits

Safety Circuit / Door Signal Error

E15

Washer stops with E15; may be associated with unbalanced load or spin issues

Unbalanced Load / Spin Protection

E16

Washer door can be opened during cycle or E16 appears related to door safety

Door Locking Safety Fault

E17

Washer shows E17 and does not fill; often associated with water inlet safety

Aqua-Stop / Inlet Safety Fault (if equipped)

E18

Washer stops with E18; often related to drain time or pump performance

Extended Drain Time / Partial Blockage

E19

Washer displays E19; may be associated with internal communication or configuration

Configuration / EEPROM Error

E20

Washer shows E20 and will not start or stops unexpectedly

General Motor Control Error

Symptom

Washer does not take detergent or softener from the dispenser drawer

Dispenser Drawer / Valve Flow Issue

Symptom

Washer door is stuck locked with no water inside and no error code

Mechanical Door Lock Jam

Symptom

Washer drum does not spin but motor can be heard running

Drive Belt Slipped or Broken

Symptom

Washer emits a burning smell or smoke during operation

Overheating Electrical Component

Symptom

Washer fills with water even when switched off

Inlet Valve Not Closing

Symptom

Washer has a bad odor inside the drum or on clothes

Biofilm / Mold Build-Up

Symptom

Washer leaks from the rear or bottom during drain or spin

Drain System Leak

Symptom

Washer leaks water from the front under the door during wash or rinse

Door Gasket (Bellows) Leak

Symptom

Washer leaves clothes very wet at the end of the cycle

Poor Spin Performance

Symptom

Washer makes loud banging or knocking noises during spin

Suspension / Shock Absorber Wear

Symptom

Washer produces a high-pitched squeal or grinding noise when spinning

Drum Bearing Failure

Symptom

Washer stops mid-cycle and water remains in drum, but no error code is shown

Intermittent Power or Control Fault

Symptom

Washer takes too long to complete a cycle

Extended Cycle Time / Heating or Fill Inefficiency

Symptom

Washer vibrates excessively and walks across the floor during spin

Excessive Vibration / Installation Issue

Symptom

Washer will not power on; no lights or display

No Power / Dead Appliance

Symptom

Washer will not start; all lights on but no response when pressing Start

User Interface / Control Lock Issue