Vremi Ice Makers Error Codes

E1

Ice maker stops and displays E1 on the control panel; unit may still power on but will not start an ice-making cycle.

Ambient Temperature Sensor Failure

E10

E10 error displayed; unit may not fill with water or may stop shortly after starting.

Water Pump / Circulation Failure

E11

E11 error on display; unit may overfill or underfill the ice-making tray; ice size may be very inconsistent.

Water Fill Valve / Flow Sensor Fault

E12

E12 error displayed; unit may shut down shortly after starting; internal fan may not run.

Condenser Fan Motor Failure

E13

E13 error on display; unit may not detect when the ice basket is in place; cycles may not start.

Ice Basket Position Switch Fault

E14

E14 error displayed; unit may freeze water but fail to release ice cubes into the basket.

Harvest Motor / Ejector Mechanism Fault

E15

E15 error on display; unit may shut down and not respond until power is cycled.

Overcurrent / Internal Protection Trip

E2

E2 error on display; ice maker powers on but will not start or complete an ice cycle; fan may run intermittently.

Evaporator Temperature Sensor Failure

E3

E3 error displayed; ice maker may start but stops mid-cycle or fails to harvest ice properly.

Water Level Sensor / Float Switch Fault

E4

E4 error appears; unit may beep and stop; ice basket may be empty or partially full.

Ice Full Sensor / Infrared Beam Fault

E5

E5 error on display; compressor may not start or may shut down quickly; unit stops making ice.

Compressor Overload / High Temperature Protection

E6

E6 error displayed; unit may power on but no ice is produced; water pump and fan may still run.

Compressor Start Failure / PTC Relay Fault

E7

E7 error on display; unit may stop mid-cycle; ice size may be inconsistent before the error appears.

Ice Thickness Sensor / Probe Fault

E8

E8 error displayed; unit may fill with water but will not freeze properly; cycles may abort early.

Defrost / Evaporator Over-ice Protection Fault

E9

E9 error on display; unit may not respond to button presses or may behave erratically.

Control Panel / Keypad Communication Error

Symptom

Buttons on the control panel do not respond or respond only intermittently.

Keypad / Touch Button Failure

Symptom

Clicking sound from compressor area; compressor tries to start but shuts off repeatedly; little or no cooling.

Compressor Hard Start / Overload Cycling

Symptom

Display lights are dim, flicker, or go out intermittently while the unit is running.

Low Voltage to Control Panel

Symptom

High-pitched squealing or grinding noise from inside the unit during operation.

Worn Fan Motor or Pump Bearings

Symptom

Ice cubes are very small, thin, or hollow; ice basket fills with weak, quickly melting cubes.

Insufficient Water Fill / Premature Harvest

Symptom

Ice cubes stick to the evaporator and do not drop into the basket; ice builds up on the plate.

Harvest Failure Due to Scale or Temperature Imbalance

Symptom

Ice maker leaks water onto the counter or inside the cabinet; puddles form under or around the unit.

Water System Leak / Drain Misrouting

Symptom

Ice maker makes ice very slowly; production is much lower than normal and cubes may be small or hollow.

Poor Heat Exchange / Partial Refrigerant Restriction

Symptom

Ice maker powers on but will not start any cycle; all indicator lights may be on or flashing, but no sounds from inside.

Main Control Board Power Supply Failure

Symptom

Ice maker runs but makes no ice at all; fan and pump may run, but the evaporator plate never gets cold.

Refrigerant Loss / Sealed System Failure

Symptom

Loud rattling or vibrating noise during operation; unit may move slightly on the counter.

Cabinet Vibration / Loose Components

Symptom

Unit cycles on and off rapidly without completing a full ice-making cycle.

Control Logic Instability / Sensor Misread

Symptom

Unit does not power on at all; no lights, no sounds, completely dead.

Incoming Power / Line Fuse Failure

Symptom

Unit emits a burning smell or visible smoke during operation.

Electrical Overheating / Component Burnout

Symptom

Unit frequently indicates 'Ice Full' and stops even when the basket is not full (no specific code).

False Ice Full Detection

Symptom

Unit frequently shows 'Add Water' or stops due to low water even when the reservoir is full (no specific code).

False Low Water Detection

Symptom

Unit is excessively hot to the touch on the sides or top during normal operation.

Cabinet Heat Soak / Inadequate Ventilation

Symptom

Unit makes a gurgling or bubbling noise from inside the cabinet.

Normal Refrigerant Flow Sounds / Possible Low Charge

Symptom

Unit produces ice with a strong plastic, chemical, or musty odor or taste.

Contaminated Water Path / New Plastic Off-gassing

Symptom

Unit runs but the internal fan does not blow air; interior feels stagnant and ice production is reduced.

Internal Circulation Fan Failure

Symptom

Unit shuts off unexpectedly after running for a short time and will not restart until it cools down.

Thermal Overload / Overheating Protection

Symptom

Visible mold, slime, or discoloration inside the water reservoir or ice bin.

Microbial Contamination of Water System

Symptom

Water appears inside the ice storage bin under the ice, causing cubes to clump and melt quickly.

Poor Ice Bin Drainage / Ambient Heat Ingress