AEG Washer-Dryer Combos Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E10
Washer-dryer does not fill with water or fills very slowly, cycle stops early with E10 on display.
Water Inlet Timeout / Filling Fault
E11
Washer-dryer attempts to fill but stops with E11, drum remains almost empty of water.
No Water Fill Detected
E13
Washer-dryer stops mid-cycle and displays E13, sometimes with water found in the base tray or under the machine.
Water Leakage Detected / Anti-Flood Activation
E20
Washer-dryer does not drain water, stops with E20, often with water remaining in the drum.
Drain Pump / Drainage Fault
E21
Washer-dryer attempts to drain but pump hums loudly or stops, then E21 appears on the display.
Drain Pump Blocked or Overloaded
E23
Washer-dryer will not start or stops with E23, often after a leak or during drain phase.
Drain Pump Triac / Pump Control Fault
E24
Washer-dryer shows E24 and may not drain or may run the pump continuously.
Drain Pump Feedback / Control Error
E30
Washer-dryer beeps and displays E30, often accompanied by the drain pump running continuously.
Water Safety System / Leak in Base
E31
Washer-dryer shows E31 and may not fill or may overfill slightly before stopping.
Pressure Sensor Signal Fault
E32
Washer-dryer intermittently stops with E32, often during filling or before spin.
Pressure Sensor Calibration / Level Error
E40
Door will not lock and cycle will not start, E40 displayed.
Door Locking System General Fault
E41
Display shows E41 and the door symbol, door appears closed but machine will not start.
Door Open Signal Fault
E42
Door remains locked at end of cycle or will not unlock, E42 displayed.
Door Unlock Fault
E43
Washer-dryer will not start or stops with E43, often related to door locking/unlocking issues.
Door Lock Triac / Control Fault
E50
Washer-dryer does not spin or tumble, sometimes shows E50 or related motor error.
General Motor Fault
E51
Washer-dryer attempts to start motor but stops and shows E51.
Motor Power Triac Short Circuit
E52
Washer-dryer drum turns erratically or not at all, E52 displayed.
Tachometer Signal Fault
E53
Washer-dryer shows E53 and will not spin, often after motor-related issues.
Motor Control Circuit Fault
E54
Washer-dryer intermittently fails to spin or reverse tumble, E54 displayed.
Motor Relay Sticking / Fault
E60
Washer-dryer does not heat water or dry clothes properly, E60 or related heating error shown.
General Heating System Fault
E61
Water does not reach the selected temperature within expected time, E61 displayed in service mode or on some models.
Heating Time-Out / Underheating
E62
Washer-dryer overheats water or shows E62, sometimes with very hot door glass.
Overheating / Overtemperature Fault
E70
Washer-dryer shows E70 and may not heat or dry correctly.
Temperature Sensor Circuit Fault
E90
Washer-dryer displays E90 and will not start or behaves erratically.
Communication / Configuration Error
E91
Display shows E91, buttons may not respond correctly.
No Communication Between Main PCB and User Interface
E92
Washer-dryer shows E92, often after replacing the control board or panel.
Configuration Mismatch Between PCB and User Interface
E93
E93 displayed, machine may not start or certain programs unavailable.
Invalid Configuration Data
E94
E94 appears and cycles may stop or not start.
Program Configuration Error
E95
E95 displayed, machine may freeze or reset unexpectedly.
EEPROM Communication Error
E96
E96 error, often after replacing power board or in regions with different mains voltage.
Incompatible Hardware Configuration
E97
E97 displayed, some programs may not be selectable.
User Interface / Program Selector Error
E98
E98 error, motor may not run or runs erratically.
Motor Control Module / Power Board Communication Fault
Symptom
Washer-dryer does not dry clothes effectively; laundry comes out damp after full dry cycle.
Poor Drying Performance
Symptom
Washer-dryer does not start at all, no lights or display, appears completely dead.
No Power / Main Supply Fault
Symptom
Washer-dryer door glass becomes extremely hot during drying, laundry feels overheated.
Drying Overheating
Symptom
Washer-dryer drum does not turn at all in wash or dry cycles, no error code shown.
Drive Belt or Motor Failure
Symptom
Washer-dryer emits a burning smell or smoke during operation.
Overheating Component or Belt Slippage
Symptom
Washer-dryer leaks water from the front during wash cycles, especially on high water level programs.
Door Seal (Bellow) Leak
Symptom
Washer-dryer leaks water from the rear or underneath during wash or drain.
Internal Hose or Pump Leak
Symptom
Washer-dryer leaves clothes very wet at the end of the cycle, spin seems weak or short.
Poor Spin Performance / Unbalanced Load Detection
Symptom
Washer-dryer leaves detergent residues or white streaks on clothes after washing.
Poor Rinsing / Detergent Dispensing Issue
Symptom
Washer-dryer makes squealing or screeching noises when the drum turns.
Drive Belt or Pulley Noise
Symptom
Washer-dryer makes very loud rumbling or roaring noise during spin, sometimes with visible drum wobble.
Drum Bearing Failure
Symptom
Washer-dryer powers on but will not start any program, start button unresponsive.
User Interface or Door Lock Start Inhibit
Symptom
Washer-dryer produces a strong musty or moldy odor from the drum and door area.
Biofilm and Mold Build-Up
Symptom
Washer-dryer produces loud banging or knocking during spin, especially with heavy loads.
Excessive Vibration / Suspension Fault
Symptom
Washer-dryer stops during drying with water collecting in the drum or poor condensation.
Drying Condensation / Pump Fault
Symptom
Washer-dryer takes excessively long to complete cycles, often pausing with drum turning slowly.
Extended Cycle Time / Heating or Drain Inefficiency
Symptom
Washer-dryer vibrates excessively and moves across the floor during spin, even when level.
Structural or Floor Instability
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E10 |
Washer-dryer does not fill with water or fills very slowly, cycle stops early with E10 on display.
|
Water Inlet Timeout / Filling Fault | View Details |
| E11 |
Washer-dryer attempts to fill but stops with E11, drum remains almost empty of water.
|
No Water Fill Detected | View Details |
| E13 |
Washer-dryer stops mid-cycle and displays E13, sometimes with water found in the base tray or under the machine.
|
Water Leakage Detected / Anti-Flood Activation | View Details |
| E20 |
Washer-dryer does not drain water, stops with E20, often with water remaining in the drum.
|
Drain Pump / Drainage Fault | View Details |
| E21 |
Washer-dryer attempts to drain but pump hums loudly or stops, then E21 appears on the display.
|
Drain Pump Blocked or Overloaded | View Details |
| E23 |
Washer-dryer will not start or stops with E23, often after a leak or during drain phase.
|
Drain Pump Triac / Pump Control Fault | View Details |
| E24 |
Washer-dryer shows E24 and may not drain or may run the pump continuously.
|
Drain Pump Feedback / Control Error | View Details |
| E30 |
Washer-dryer beeps and displays E30, often accompanied by the drain pump running continuously.
|
Water Safety System / Leak in Base | View Details |
| E31 |
Washer-dryer shows E31 and may not fill or may overfill slightly before stopping.
|
Pressure Sensor Signal Fault | View Details |
| E32 |
Washer-dryer intermittently stops with E32, often during filling or before spin.
|
Pressure Sensor Calibration / Level Error | View Details |
| E40 |
Door will not lock and cycle will not start, E40 displayed.
|
Door Locking System General Fault | View Details |
| E41 |
Display shows E41 and the door symbol, door appears closed but machine will not start.
|
Door Open Signal Fault | View Details |
| E42 |
Door remains locked at end of cycle or will not unlock, E42 displayed.
|
Door Unlock Fault | View Details |
| E43 |
Washer-dryer will not start or stops with E43, often related to door locking/unlocking issues.
|
Door Lock Triac / Control Fault | View Details |
| E50 |
Washer-dryer does not spin or tumble, sometimes shows E50 or related motor error.
|
General Motor Fault | View Details |
| E51 |
Washer-dryer attempts to start motor but stops and shows E51.
|
Motor Power Triac Short Circuit | View Details |
| E52 |
Washer-dryer drum turns erratically or not at all, E52 displayed.
|
Tachometer Signal Fault | View Details |
| E53 |
Washer-dryer shows E53 and will not spin, often after motor-related issues.
|
Motor Control Circuit Fault | View Details |
| E54 |
Washer-dryer intermittently fails to spin or reverse tumble, E54 displayed.
|
Motor Relay Sticking / Fault | View Details |
| E60 |
Washer-dryer does not heat water or dry clothes properly, E60 or related heating error shown.
|
General Heating System Fault | View Details |
| E61 |
Water does not reach the selected temperature within expected time, E61 displayed in service mode or on some models.
|
Heating Time-Out / Underheating | View Details |
| E62 |
Washer-dryer overheats water or shows E62, sometimes with very hot door glass.
|
Overheating / Overtemperature Fault | View Details |
| E70 |
Washer-dryer shows E70 and may not heat or dry correctly.
|
Temperature Sensor Circuit Fault | View Details |
| E90 |
Washer-dryer displays E90 and will not start or behaves erratically.
|
Communication / Configuration Error | View Details |
| E91 |
Display shows E91, buttons may not respond correctly.
|
No Communication Between Main PCB and User Interface | View Details |
| E92 |
Washer-dryer shows E92, often after replacing the control board or panel.
|
Configuration Mismatch Between PCB and User Interface | View Details |
| E93 |
E93 displayed, machine may not start or certain programs unavailable.
|
Invalid Configuration Data | View Details |
| E94 |
E94 appears and cycles may stop or not start.
|
Program Configuration Error | View Details |
| E95 |
E95 displayed, machine may freeze or reset unexpectedly.
|
EEPROM Communication Error | View Details |
| E96 |
E96 error, often after replacing power board or in regions with different mains voltage.
|
Incompatible Hardware Configuration | View Details |
| E97 |
E97 displayed, some programs may not be selectable.
|
User Interface / Program Selector Error | View Details |
| E98 |
E98 error, motor may not run or runs erratically.
|
Motor Control Module / Power Board Communication Fault | View Details |
| – |
Washer-dryer does not dry clothes effectively; laundry comes out damp after full dry cycle.
|
Poor Drying Performance | View Details |
| – |
Washer-dryer does not start at all, no lights or display, appears completely dead.
|
No Power / Main Supply Fault | View Details |
| – |
Washer-dryer door glass becomes extremely hot during drying, laundry feels overheated.
|
Drying Overheating | View Details |
| – |
Washer-dryer drum does not turn at all in wash or dry cycles, no error code shown.
|
Drive Belt or Motor Failure | View Details |
| – |
Washer-dryer emits a burning smell or smoke during operation.
|
Overheating Component or Belt Slippage | View Details |
| – |
Washer-dryer leaks water from the front during wash cycles, especially on high water level programs.
|
Door Seal (Bellow) Leak | View Details |
| – |
Washer-dryer leaks water from the rear or underneath during wash or drain.
|
Internal Hose or Pump Leak | View Details |
| – |
Washer-dryer leaves clothes very wet at the end of the cycle, spin seems weak or short.
|
Poor Spin Performance / Unbalanced Load Detection | View Details |
| – |
Washer-dryer leaves detergent residues or white streaks on clothes after washing.
|
Poor Rinsing / Detergent Dispensing Issue | View Details |
| – |
Washer-dryer makes squealing or screeching noises when the drum turns.
|
Drive Belt or Pulley Noise | View Details |
| – |
Washer-dryer makes very loud rumbling or roaring noise during spin, sometimes with visible drum wobble.
|
Drum Bearing Failure | View Details |
| – |
Washer-dryer powers on but will not start any program, start button unresponsive.
|
User Interface or Door Lock Start Inhibit | View Details |
| – |
Washer-dryer produces a strong musty or moldy odor from the drum and door area.
|
Biofilm and Mold Build-Up | View Details |
| – |
Washer-dryer produces loud banging or knocking during spin, especially with heavy loads.
|
Excessive Vibration / Suspension Fault | View Details |
| – |
Washer-dryer stops during drying with water collecting in the drum or poor condensation.
|
Drying Condensation / Pump Fault | View Details |
| – |
Washer-dryer takes excessively long to complete cycles, often pausing with drum turning slowly.
|
Extended Cycle Time / Heating or Drain Inefficiency | View Details |
| – |
Washer-dryer vibrates excessively and moves across the floor during spin, even when level.
|
Structural or Floor Instability | View Details |
No matching codes found
Advertisements