Toshiba Washing Machines Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E1
Washer stops mid-cycle and displays E1; water does not drain or drains very slowly.
Drain System Failure
E10
Washer shows E10 and does not start; control panel may be unresponsive or stuck.
Control Panel / Communication Error
E11
Washer displays E11; door remains locked at the end of the cycle or will not unlock.
Door Unlock Failure
E12
Washer shows E12; heating function does not work or water does not reach target temperature.
Heater Circuit Fault
E13
Washer displays E13; motor speed feedback error, drum may jerk or not reach full spin speed.
Motor Tachometer / Hall Sensor Fault
E2
Washer displays E2 and will not proceed to spin; lid or door does not lock properly.
Lid/Door Lock Failure
E21
Washer shows E21; drain time exceeds limit, water remains in drum at end of cycle.
Extended Drain Time / Partial Blockage
E23
Washer displays E23; door lock circuit error, machine may not start.
Door Lock Circuit Error
E3
Washer displays E3 and stops; drum appears overloaded or unbalanced, often during spin.
Unbalanced Load / Overload Detection
E31
Washer shows E31; water level sensor signal out of range at start of cycle.
Water Level Sensor Out-of-Range Error
E32
Washer displays E32; water level does not change as expected during fill or drain.
Water Level Change Timeout
E4
Washer shows E4 and does not fill with water or fills very slowly.
Water Inlet Failure
E5
Washer displays E5; water level does not reach the correct height or overfills/underfills.
Water Level Sensor (Pressure Switch) Error
E51
Washer shows E51; motor overcurrent or overload detected, drum may stop abruptly.
Motor Overcurrent Protection
E52
Washer displays E52; motor does not start or runs erratically at low speed.
Motor Start Failure / Inverter Error
E6
Washer shows E6 and will not spin or agitate; motor does not run.
Motor Drive Fault
E61
Washer shows E61; heating time too long or water does not reach set temperature within allowed time.
Heating Timeout
E62
Washer displays E62; overheating detected, water temperature exceeds safe limit.
Overheating Protection
E7
Washer displays E7; spin cycle does not start or stops quickly, often with heavy loads.
Clutch / Transmission or Motor Overload Fault (Top-Load Models)
E71
Washer shows E71; NTC temperature sensor open or short circuit detected.
NTC Sensor Circuit Fault
E8
Washer shows E8; water level rises abnormally or overflows, or the machine detects abnormal water level signal.
Abnormal Water Level / Overflow Protection
E9
Washer displays E9; water leaks detected in base tray or abnormal water level drop.
Leak Detection / Water Escape Fault
E91
Washer displays E91; communication error between main control board and user interface.
Communication Bus Error
E92
Washer shows E92; configuration or EEPROM error on control board.
Configuration / Memory Error
E93
Washer displays E93; incompatible or missing configuration data for installed hardware.
Hardware Configuration Mismatch
E94
Washer shows E94; program sequence or software error detected.
Program Sequence Error
E95
Washer displays E95; communication error between main PCB and motor inverter module.
Main PCB–Inverter Communication Fault
Symptom
Washer displays random lights or buttons do not respond correctly; panel behaves erratically.
User Interface Malfunction
Symptom
Washer does not spin or spins very slowly; clothes come out very wet.
Spin Failure / Low Spin Speed
Symptom
Washer door or lid slams shut or does not stay open properly.
Door Hinge / Damper Wear
Symptom
Washer drum has excessive play; you can lift it up and down noticeably by hand.
Suspension / Support Wear
Symptom
Washer emits a burning smell or electrical odor during operation.
Overheating Electrical Component
Symptom
Washer fills with water but does not agitate or tumble; drum stays still during wash phase.
Agitation / Wash Motor Failure
Symptom
Washer has a strong moldy or musty odor inside the drum.
Biofilm / Mold Build-Up
Symptom
Washer is dead: no lights, no display, no response when power button is pressed.
No Power / Power Supply Failure
Symptom
Washer is very noisy during spin; loud rumbling or grinding sound from the drum area.
Drum Bearing Failure
Symptom
Washer leaks water from the front door area during wash or spin.
Door Gasket / Bellows Leak
Symptom
Washer leaks water from underneath the machine.
Internal Hose or Pump Leak
Symptom
Washer leaves detergent residue or white streaks on clothes after washing.
Poor Rinsing / Detergent Dissolution Issue
Symptom
Washer makes loud banging or knocking noises during spin; machine may move or walk across the floor.
Excessive Vibration / Suspension Failure
Symptom
Washer powers on but will not start any cycle; Start button beeps or flashes but nothing happens.
Start Inhibit / Door Not Ready
Symptom
Washer takes much longer than expected to complete a cycle.
Extended Cycle Time / Adaptive Control Response
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E1 |
Washer stops mid-cycle and displays E1; water does not drain or drains very slowly.
|
Drain System Failure | View Details |
| E10 |
Washer shows E10 and does not start; control panel may be unresponsive or stuck.
|
Control Panel / Communication Error | View Details |
| E11 |
Washer displays E11; door remains locked at the end of the cycle or will not unlock.
|
Door Unlock Failure | View Details |
| E12 |
Washer shows E12; heating function does not work or water does not reach target temperature.
|
Heater Circuit Fault | View Details |
| E13 |
Washer displays E13; motor speed feedback error, drum may jerk or not reach full spin speed.
|
Motor Tachometer / Hall Sensor Fault | View Details |
| E2 |
Washer displays E2 and will not proceed to spin; lid or door does not lock properly.
|
Lid/Door Lock Failure | View Details |
| E21 |
Washer shows E21; drain time exceeds limit, water remains in drum at end of cycle.
|
Extended Drain Time / Partial Blockage | View Details |
| E23 |
Washer displays E23; door lock circuit error, machine may not start.
|
Door Lock Circuit Error | View Details |
| E3 |
Washer displays E3 and stops; drum appears overloaded or unbalanced, often during spin.
|
Unbalanced Load / Overload Detection | View Details |
| E31 |
Washer shows E31; water level sensor signal out of range at start of cycle.
|
Water Level Sensor Out-of-Range Error | View Details |
| E32 |
Washer displays E32; water level does not change as expected during fill or drain.
|
Water Level Change Timeout | View Details |
| E4 |
Washer shows E4 and does not fill with water or fills very slowly.
|
Water Inlet Failure | View Details |
| E5 |
Washer displays E5; water level does not reach the correct height or overfills/underfills.
|
Water Level Sensor (Pressure Switch) Error | View Details |
| E51 |
Washer shows E51; motor overcurrent or overload detected, drum may stop abruptly.
|
Motor Overcurrent Protection | View Details |
| E52 |
Washer displays E52; motor does not start or runs erratically at low speed.
|
Motor Start Failure / Inverter Error | View Details |
| E6 |
Washer shows E6 and will not spin or agitate; motor does not run.
|
Motor Drive Fault | View Details |
| E61 |
Washer shows E61; heating time too long or water does not reach set temperature within allowed time.
|
Heating Timeout | View Details |
| E62 |
Washer displays E62; overheating detected, water temperature exceeds safe limit.
|
Overheating Protection | View Details |
| E7 |
Washer displays E7; spin cycle does not start or stops quickly, often with heavy loads.
|
Clutch / Transmission or Motor Overload Fault (Top-Load Models) | View Details |
| E71 |
Washer shows E71; NTC temperature sensor open or short circuit detected.
|
NTC Sensor Circuit Fault | View Details |
| E8 |
Washer shows E8; water level rises abnormally or overflows, or the machine detects abnormal water level signal.
|
Abnormal Water Level / Overflow Protection | View Details |
| E9 |
Washer displays E9; water leaks detected in base tray or abnormal water level drop.
|
Leak Detection / Water Escape Fault | View Details |
| E91 |
Washer displays E91; communication error between main control board and user interface.
|
Communication Bus Error | View Details |
| E92 |
Washer shows E92; configuration or EEPROM error on control board.
|
Configuration / Memory Error | View Details |
| E93 |
Washer displays E93; incompatible or missing configuration data for installed hardware.
|
Hardware Configuration Mismatch | View Details |
| E94 |
Washer shows E94; program sequence or software error detected.
|
Program Sequence Error | View Details |
| E95 |
Washer displays E95; communication error between main PCB and motor inverter module.
|
Main PCB–Inverter Communication Fault | View Details |
| – |
Washer displays random lights or buttons do not respond correctly; panel behaves erratically.
|
User Interface Malfunction | View Details |
| – |
Washer does not spin or spins very slowly; clothes come out very wet.
|
Spin Failure / Low Spin Speed | View Details |
| – |
Washer door or lid slams shut or does not stay open properly.
|
Door Hinge / Damper Wear | View Details |
| – |
Washer drum has excessive play; you can lift it up and down noticeably by hand.
|
Suspension / Support Wear | View Details |
| – |
Washer emits a burning smell or electrical odor during operation.
|
Overheating Electrical Component | View Details |
| – |
Washer fills with water but does not agitate or tumble; drum stays still during wash phase.
|
Agitation / Wash Motor Failure | View Details |
| – |
Washer has a strong moldy or musty odor inside the drum.
|
Biofilm / Mold Build-Up | View Details |
| – |
Washer is dead: no lights, no display, no response when power button is pressed.
|
No Power / Power Supply Failure | View Details |
| – |
Washer is very noisy during spin; loud rumbling or grinding sound from the drum area.
|
Drum Bearing Failure | View Details |
| – |
Washer leaks water from the front door area during wash or spin.
|
Door Gasket / Bellows Leak | View Details |
| – |
Washer leaks water from underneath the machine.
|
Internal Hose or Pump Leak | View Details |
| – |
Washer leaves detergent residue or white streaks on clothes after washing.
|
Poor Rinsing / Detergent Dissolution Issue | View Details |
| – |
Washer makes loud banging or knocking noises during spin; machine may move or walk across the floor.
|
Excessive Vibration / Suspension Failure | View Details |
| – |
Washer powers on but will not start any cycle; Start button beeps or flashes but nothing happens.
|
Start Inhibit / Door Not Ready | View Details |
| – |
Washer takes much longer than expected to complete a cycle.
|
Extended Cycle Time / Adaptive Control Response | View Details |
No matching codes found
Advertisements