Hisense Washing Machines Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E1
Washer will not fill with water, E1 displayed shortly after cycle start
Water Inlet Timeout / No Fill
E10
Washer shows E10 and stops, often at the beginning of the cycle
Door Not Closed / Door Switch Error
E11
Washer displays E11, cycle stops unexpectedly, often with water still in drum
Communication Error Between Main PCB and Motor/Inverter
E12
Washer shows E12, drum does not rotate correctly during wash or spin
Motor Overload / Stall Detection
E13
Washer displays E13, often associated with water leakage into base
Leakage Detected / Anti-Flood Protection
E2
Washer does not drain water, E2 displayed, drum remains full
Drain Timeout / No Drain
E21
Washer shows E21, drum speed abnormal during spin
Spin Speed Sensor / Unstable Spin Fault
E3
Washer drum does not spin or spin is very weak, E3 displayed
Motor Drive Fault / No Spin
E30
Washer displays E30 and will not start or stops mid-cycle
Door Locking System General Fault
E31
Washer shows E31, water temperature reading appears incorrect (very hot or very cold) and cycle aborts
NTC Temperature Sensor Fault
E32
Washer displays E32, water level reading unstable, frequent fill and drain
Pressure Sensor Calibration / Range Error
E4
Washer displays E4 and stops during spin, drum tries to spin but stops repeatedly
Unbalanced Load / Out-of-Balance Detection
E40
Washer shows E40 and will not start, often accompanied by beeping
Door Open Detected at Start
E41
Washer displays E41 during cycle, door reported as open while running
Door Lock Signal Lost During Operation
E5
Washer does not heat water, E5 displayed during wash cycle
Water Heating Fault
E51
Washer shows E51, motor does not run or runs erratically
Motor Power Triac / Inverter Fault
E6
Washer stops mid-cycle with E6, water level appears incorrect or erratic
Water Level Sensor / Pressure Switch Fault
E60
Washer displays E60, heating-related malfunction (no heat or overheating)
General Heating System Error
E7
Washer door will not lock or unlock, E7 displayed
Door Lock / Interlock Fault
E8
Washer shows E8 and will not start or stops shortly after starting
Motor Tachometer / Speed Feedback Fault
E9
Washer displays E9, water level rises too high or overflows into the door gasket
Overfill / Overflow Protection
E90
Washer shows E90, often after a power outage or surge, machine unresponsive or erratic
Configuration / Communication Error
F01
Washer displays F01 and will not start a cycle
Water Supply Fault / Low Inlet Flow
F02
Washer shows F02, drum not rotating properly during wash
Motor Drive Error
F03
Washer displays F03, water not draining at end of cycle
Drain Pump Fault
F04
Washer shows F04, water level error at start or during wash
Pressure Switch / Water Level Error
F05
Washer displays F05, heater not functioning correctly
Heating Circuit Error
F06
Washer shows F06, door lock error at start
Door Lock Failure
F07
Washer displays F07, motor-related fault during spin
Motor/Tachometer Error
F08
Washer shows F08, water level too high or overflow condition
Overfill Error
F09
Washer displays F09, internal software/configuration error
EEPROM / Configuration Fault
Symptom
Washer causes lights to flicker or trips the circuit breaker when starting
Electrical Overload / Short Circuit
Symptom
Washer door remains locked after cycle ends and no error code is shown
Door Lock Stuck Closed
Symptom
Washer drum does not turn at all during wash but can be turned by hand
Drive System Failure
Symptom
Washer emits a burning smell or smoke during operation
Overheating Electrical or Drive Component
Symptom
Washer fills and drains repeatedly without progressing into wash
Water Level Sensing / Siphoning Issue
Symptom
Washer has a strong musty or moldy odor inside the drum
Biofilm and Mold Build-Up
Symptom
Washer leaks water from the front door area during wash or rinse
Door Gasket (Boot Seal) Leak
Symptom
Washer leaks water from underneath the cabinet during wash or spin
Internal Hose or Pump Leak
Symptom
Washer leaves clothes very wet at the end of the cycle
Poor Spin Performance
Symptom
Washer leaves visible detergent or powder residue on clothes
Poor Rinsing / Detergent Dispensing Issue
Symptom
Washer makes loud banging or knocking noises during spin
Excessive Vibration / Suspension Failure
Symptom
Washer powers on but will not start any cycle when Start/Pause is pressed
User Interface / Control Lock or Start Circuit Issue
Symptom
Washer produces a high-pitched squealing or grinding noise when spinning
Drum Bearing or Drive System Wear
Symptom
Washer takes much longer than the displayed time to complete a cycle
Extended Cycle Time / Auto Time Adjustment
Symptom
Washer vibrates excessively and walks across the floor even with small loads
Installation / Suspension Imbalance
Symptom
Washer will not power on, no lights or display
No Power / Dead Appliance
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E1 |
Washer will not fill with water, E1 displayed shortly after cycle start
|
Water Inlet Timeout / No Fill | View Details |
| E10 |
Washer shows E10 and stops, often at the beginning of the cycle
|
Door Not Closed / Door Switch Error | View Details |
| E11 |
Washer displays E11, cycle stops unexpectedly, often with water still in drum
|
Communication Error Between Main PCB and Motor/Inverter | View Details |
| E12 |
Washer shows E12, drum does not rotate correctly during wash or spin
|
Motor Overload / Stall Detection | View Details |
| E13 |
Washer displays E13, often associated with water leakage into base
|
Leakage Detected / Anti-Flood Protection | View Details |
| E2 |
Washer does not drain water, E2 displayed, drum remains full
|
Drain Timeout / No Drain | View Details |
| E21 |
Washer shows E21, drum speed abnormal during spin
|
Spin Speed Sensor / Unstable Spin Fault | View Details |
| E3 |
Washer drum does not spin or spin is very weak, E3 displayed
|
Motor Drive Fault / No Spin | View Details |
| E30 |
Washer displays E30 and will not start or stops mid-cycle
|
Door Locking System General Fault | View Details |
| E31 |
Washer shows E31, water temperature reading appears incorrect (very hot or very cold) and cycle aborts
|
NTC Temperature Sensor Fault | View Details |
| E32 |
Washer displays E32, water level reading unstable, frequent fill and drain
|
Pressure Sensor Calibration / Range Error | View Details |
| E4 |
Washer displays E4 and stops during spin, drum tries to spin but stops repeatedly
|
Unbalanced Load / Out-of-Balance Detection | View Details |
| E40 |
Washer shows E40 and will not start, often accompanied by beeping
|
Door Open Detected at Start | View Details |
| E41 |
Washer displays E41 during cycle, door reported as open while running
|
Door Lock Signal Lost During Operation | View Details |
| E5 |
Washer does not heat water, E5 displayed during wash cycle
|
Water Heating Fault | View Details |
| E51 |
Washer shows E51, motor does not run or runs erratically
|
Motor Power Triac / Inverter Fault | View Details |
| E6 |
Washer stops mid-cycle with E6, water level appears incorrect or erratic
|
Water Level Sensor / Pressure Switch Fault | View Details |
| E60 |
Washer displays E60, heating-related malfunction (no heat or overheating)
|
General Heating System Error | View Details |
| E7 |
Washer door will not lock or unlock, E7 displayed
|
Door Lock / Interlock Fault | View Details |
| E8 |
Washer shows E8 and will not start or stops shortly after starting
|
Motor Tachometer / Speed Feedback Fault | View Details |
| E9 |
Washer displays E9, water level rises too high or overflows into the door gasket
|
Overfill / Overflow Protection | View Details |
| E90 |
Washer shows E90, often after a power outage or surge, machine unresponsive or erratic
|
Configuration / Communication Error | View Details |
| F01 |
Washer displays F01 and will not start a cycle
|
Water Supply Fault / Low Inlet Flow | View Details |
| F02 |
Washer shows F02, drum not rotating properly during wash
|
Motor Drive Error | View Details |
| F03 |
Washer displays F03, water not draining at end of cycle
|
Drain Pump Fault | View Details |
| F04 |
Washer shows F04, water level error at start or during wash
|
Pressure Switch / Water Level Error | View Details |
| F05 |
Washer displays F05, heater not functioning correctly
|
Heating Circuit Error | View Details |
| F06 |
Washer shows F06, door lock error at start
|
Door Lock Failure | View Details |
| F07 |
Washer displays F07, motor-related fault during spin
|
Motor/Tachometer Error | View Details |
| F08 |
Washer shows F08, water level too high or overflow condition
|
Overfill Error | View Details |
| F09 |
Washer displays F09, internal software/configuration error
|
EEPROM / Configuration Fault | View Details |
| – |
Washer causes lights to flicker or trips the circuit breaker when starting
|
Electrical Overload / Short Circuit | View Details |
| – |
Washer door remains locked after cycle ends and no error code is shown
|
Door Lock Stuck Closed | View Details |
| – |
Washer drum does not turn at all during wash but can be turned by hand
|
Drive System Failure | View Details |
| – |
Washer emits a burning smell or smoke during operation
|
Overheating Electrical or Drive Component | View Details |
| – |
Washer fills and drains repeatedly without progressing into wash
|
Water Level Sensing / Siphoning Issue | View Details |
| – |
Washer has a strong musty or moldy odor inside the drum
|
Biofilm and Mold Build-Up | View Details |
| – |
Washer leaks water from the front door area during wash or rinse
|
Door Gasket (Boot Seal) Leak | View Details |
| – |
Washer leaks water from underneath the cabinet during wash or spin
|
Internal Hose or Pump Leak | View Details |
| – |
Washer leaves clothes very wet at the end of the cycle
|
Poor Spin Performance | View Details |
| – |
Washer leaves visible detergent or powder residue on clothes
|
Poor Rinsing / Detergent Dispensing Issue | View Details |
| – |
Washer makes loud banging or knocking noises during spin
|
Excessive Vibration / Suspension Failure | View Details |
| – |
Washer powers on but will not start any cycle when Start/Pause is pressed
|
User Interface / Control Lock or Start Circuit Issue | View Details |
| – |
Washer produces a high-pitched squealing or grinding noise when spinning
|
Drum Bearing or Drive System Wear | View Details |
| – |
Washer takes much longer than the displayed time to complete a cycle
|
Extended Cycle Time / Auto Time Adjustment | View Details |
| – |
Washer vibrates excessively and walks across the floor even with small loads
|
Installation / Suspension Imbalance | View Details |
| – |
Washer will not power on, no lights or display
|
No Power / Dead Appliance | View Details |
No matching codes found
Advertisements