Asko Ranges & Cooktops Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E0
Induction cooktop displays E0 when attempting to use a zone.
No Cookware Detected
E1
Induction cooktop shows E1 and beeps, zone will not heat.
NTC Sensor Open Circuit
E2
Induction cooktop shows E2 and shuts down the affected zone.
NTC Sensor Short Circuit / Overtemperature
E3
Induction cooktop displays E3 and all zones shut down during heavy use.
Cooktop Overtemperature Protection
E4
Induction cooktop shows E4 on a specific zone and it will not heat.
Induction Coil Open Circuit
E5
Induction cooktop displays E5 and beeps when turned on.
Internal Power Supply Fault
E6
Induction cooktop shows E6 and all zones are disabled.
Overvoltage Protection
E7
Induction cooktop displays E7 intermittently and zones shut off unexpectedly.
Communication Error Between UI and Power Board
E8
Induction cooktop shows E8 and one side of the cooktop is inoperative.
Half-Bridge / Side Power Module Failure
E9
Induction cooktop displays E9 and will not power on fully.
Internal Configuration / Model Mismatch Error
F1
Induction cooktop beeps and shuts off shortly after power-up, F1 displayed on one or more zones.
Cooktop Touch Control Panel Communication Fault
F10
Asko range oven display shows F10 and beeps; oven shuts off.
Oven Temperature Sensor (RTD) Fault
F2
Induction cooktop displays F2 and disables one or more cooking zones.
Induction Power Module Overtemperature Fault
F20
Asko range displays F20 and oven will not start a cooking cycle.
Oven Door Lock / Latch Fault (Self-Clean Models)
F3
Cooktop shows F3 on one zone and that zone will not heat.
Glass Surface Temperature Sensor Fault
F30
Asko range cooktop section shows F30 and one or more radiant elements will not heat.
Radiant Element Temperature Limiter Fault
F4
Induction cooktop displays F4 and one or more zones are disabled.
Induction Coil or Power Module Fault
F40
Asko gas cooktop with electronic ignition shows F40 or flashes a fault indicator; burners will not ignite.
Ignition Module Fault
F5
Cooktop shows F5 and beeps when trying to use a zone.
Pan Detection / Induction Load Fault
F50
Asko range displays F50 and oven fan does not run during cooking or cooling.
Cooling Fan Fault
F6
Cooktop displays F6 and will not allow operation of one or more zones.
Supply Voltage Out of Range
F7
Cooktop shows F7 and touch controls are unresponsive or erratic.
Touch Keypad / Glass Interface Fault
F8
Induction cooktop displays F8 and shuts down during use.
Internal Overcurrent / Short Circuit Protection
F9
Cooktop shows F9 and will not start any zones.
Configuration / EEPROM Error
LOC
Range or cooktop display shows LOC or a key symbol and controls do not respond.
Control Lock (Child Lock) Activated
PF
Asko range display shows PF and clock is flashing after a power interruption.
Power Failure Indication
Symptom
Cooktop controls are completely dead; no lights or response.
No Power to Control System
Symptom
Cooktop glass surface is cracked or shattered.
Ceramic Glass Top Structural Failure
Symptom
Cooktop makes loud buzzing or humming noises during induction operation.
Induction Acoustic Noise / Coil Vibration
Symptom
Cooktop or range emits a burning smell or light smoke during use.
Overheating or Residue Burning Off
Symptom
Cooktop or range trips the circuit breaker when a burner or zone is turned on.
Electrical Short or Overcurrent
Symptom
Cooktop surface around burners becomes excessively hot or discolors.
Localized Overheating / Heat Migration
Symptom
Cooktop touch controls are erratic or respond only intermittently.
Touch Sensor Sensitivity / Calibration Issue
Symptom
Electric radiant element does not heat at all; indicator light may or may not come on.
Open Radiant Heating Element Circuit
Symptom
Gas burner ignites but flame is weak, yellow, or noisy.
Improper Gas-Air Mixture or Supply Issue
Symptom
Gas burner keeps clicking even after flame is established.
Continuous Ignition / Stuck Spark Switch
Symptom
Gas burner will not ignite; no clicking sound and no flame on any burner.
Complete Ignition System Failure
Symptom
Induction zone cycles on and off rapidly or power level seems unstable.
Intermittent Pan Detection / Load Instability
Symptom
Oven cooling fan runs continuously long after the oven has been turned off.
Cooling Fan Control Stuck On
Symptom
Oven door on Asko range will not close fully or pops open slightly during baking.
Door Hinge or Gasket Misalignment
Symptom
Oven in Asko range does not heat, but cooktop works normally.
Oven Heating Circuit Failure
Symptom
Oven temperature is inaccurate; food undercooked or overcooked compared to set temperature.
Oven Temperature Calibration / Sensor Drift
Symptom
Single gas burner will not ignite but others work normally; clicking is present.
Individual Burner Ignition Failure
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E0 |
Induction cooktop displays E0 when attempting to use a zone.
|
No Cookware Detected | View Details |
| E1 |
Induction cooktop shows E1 and beeps, zone will not heat.
|
NTC Sensor Open Circuit | View Details |
| E2 |
Induction cooktop shows E2 and shuts down the affected zone.
|
NTC Sensor Short Circuit / Overtemperature | View Details |
| E3 |
Induction cooktop displays E3 and all zones shut down during heavy use.
|
Cooktop Overtemperature Protection | View Details |
| E4 |
Induction cooktop shows E4 on a specific zone and it will not heat.
|
Induction Coil Open Circuit | View Details |
| E5 |
Induction cooktop displays E5 and beeps when turned on.
|
Internal Power Supply Fault | View Details |
| E6 |
Induction cooktop shows E6 and all zones are disabled.
|
Overvoltage Protection | View Details |
| E7 |
Induction cooktop displays E7 intermittently and zones shut off unexpectedly.
|
Communication Error Between UI and Power Board | View Details |
| E8 |
Induction cooktop shows E8 and one side of the cooktop is inoperative.
|
Half-Bridge / Side Power Module Failure | View Details |
| E9 |
Induction cooktop displays E9 and will not power on fully.
|
Internal Configuration / Model Mismatch Error | View Details |
| F1 |
Induction cooktop beeps and shuts off shortly after power-up, F1 displayed on one or more zones.
|
Cooktop Touch Control Panel Communication Fault | View Details |
| F10 |
Asko range oven display shows F10 and beeps; oven shuts off.
|
Oven Temperature Sensor (RTD) Fault | View Details |
| F2 |
Induction cooktop displays F2 and disables one or more cooking zones.
|
Induction Power Module Overtemperature Fault | View Details |
| F20 |
Asko range displays F20 and oven will not start a cooking cycle.
|
Oven Door Lock / Latch Fault (Self-Clean Models) | View Details |
| F3 |
Cooktop shows F3 on one zone and that zone will not heat.
|
Glass Surface Temperature Sensor Fault | View Details |
| F30 |
Asko range cooktop section shows F30 and one or more radiant elements will not heat.
|
Radiant Element Temperature Limiter Fault | View Details |
| F4 |
Induction cooktop displays F4 and one or more zones are disabled.
|
Induction Coil or Power Module Fault | View Details |
| F40 |
Asko gas cooktop with electronic ignition shows F40 or flashes a fault indicator; burners will not ignite.
|
Ignition Module Fault | View Details |
| F5 |
Cooktop shows F5 and beeps when trying to use a zone.
|
Pan Detection / Induction Load Fault | View Details |
| F50 |
Asko range displays F50 and oven fan does not run during cooking or cooling.
|
Cooling Fan Fault | View Details |
| F6 |
Cooktop displays F6 and will not allow operation of one or more zones.
|
Supply Voltage Out of Range | View Details |
| F7 |
Cooktop shows F7 and touch controls are unresponsive or erratic.
|
Touch Keypad / Glass Interface Fault | View Details |
| F8 |
Induction cooktop displays F8 and shuts down during use.
|
Internal Overcurrent / Short Circuit Protection | View Details |
| F9 |
Cooktop shows F9 and will not start any zones.
|
Configuration / EEPROM Error | View Details |
| LOC |
Range or cooktop display shows LOC or a key symbol and controls do not respond.
|
Control Lock (Child Lock) Activated | View Details |
| PF |
Asko range display shows PF and clock is flashing after a power interruption.
|
Power Failure Indication | View Details |
| – |
Cooktop controls are completely dead; no lights or response.
|
No Power to Control System | View Details |
| – |
Cooktop glass surface is cracked or shattered.
|
Ceramic Glass Top Structural Failure | View Details |
| – |
Cooktop makes loud buzzing or humming noises during induction operation.
|
Induction Acoustic Noise / Coil Vibration | View Details |
| – |
Cooktop or range emits a burning smell or light smoke during use.
|
Overheating or Residue Burning Off | View Details |
| – |
Cooktop or range trips the circuit breaker when a burner or zone is turned on.
|
Electrical Short or Overcurrent | View Details |
| – |
Cooktop surface around burners becomes excessively hot or discolors.
|
Localized Overheating / Heat Migration | View Details |
| – |
Cooktop touch controls are erratic or respond only intermittently.
|
Touch Sensor Sensitivity / Calibration Issue | View Details |
| – |
Electric radiant element does not heat at all; indicator light may or may not come on.
|
Open Radiant Heating Element Circuit | View Details |
| – |
Gas burner ignites but flame is weak, yellow, or noisy.
|
Improper Gas-Air Mixture or Supply Issue | View Details |
| – |
Gas burner keeps clicking even after flame is established.
|
Continuous Ignition / Stuck Spark Switch | View Details |
| – |
Gas burner will not ignite; no clicking sound and no flame on any burner.
|
Complete Ignition System Failure | View Details |
| – |
Induction zone cycles on and off rapidly or power level seems unstable.
|
Intermittent Pan Detection / Load Instability | View Details |
| – |
Oven cooling fan runs continuously long after the oven has been turned off.
|
Cooling Fan Control Stuck On | View Details |
| – |
Oven door on Asko range will not close fully or pops open slightly during baking.
|
Door Hinge or Gasket Misalignment | View Details |
| – |
Oven in Asko range does not heat, but cooktop works normally.
|
Oven Heating Circuit Failure | View Details |
| – |
Oven temperature is inaccurate; food undercooked or overcooked compared to set temperature.
|
Oven Temperature Calibration / Sensor Drift | View Details |
| – |
Single gas burner will not ignite but others work normally; clicking is present.
|
Individual Burner Ignition Failure | View Details |
No matching codes found
Advertisements