Fagor Dryers Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E01
Dryer will not start; display shows E01 immediately after pressing the start button.
Door Lock / Door Switch Fault
E02
Dryer stops shortly after starting and displays E02; drum may tumble briefly then shut off.
Overheating / High Temperature Cut-Out
E03
Dryer displays E03 and stops; clothes remain damp; often occurs early in the cycle.
NTC Temperature Sensor Fault
E04
Dryer shows E04 and will not start or stops mid-cycle; may be accompanied by no heat.
Heating Circuit Failure
E05
Dryer displays E05 and does not start; sometimes accompanied by a humming noise from the motor area.
Motor Start Failure / Motor Circuit Fault
E06
Dryer shows E06 and stops; may not heat properly or may overheat; cycle times become erratic.
Moisture Sensor / Humidity Detection Fault
E07
Dryer displays E07 and stops; on condenser models, water may not collect in the tank or may leak.
Condenser Pump / Drainage Fault
E08
Dryer shows E08; drum may not rotate even though the motor can be heard or attempts to start.
Drive Belt / Drum Rotation Fault
E09
Dryer displays E09 and will not start; sometimes occurs after a power surge or outage.
Control Board / EEPROM Error
E10
Dryer shows E10 and does not start; often associated with incorrect or unstable mains voltage.
Power Supply / Voltage Detection Fault
E11
Dryer displays E11; on condenser models, drying performance is poor and the unit may stop prematurely.
Condenser Airflow / Heat Exchanger Blockage
E12
Dryer shows E12; cycle may not start or may stop; often related to sensor drying programs.
Program Selector / User Interface Communication Fault
E13
Dryer displays E13; may be accompanied by unusual noises or failure to rotate.
Tachometer / Motor Speed Feedback Fault
E14
Dryer shows E14 and stops; may be associated with overheating or very long drying times.
Exhaust Air Temperature / Outlet Sensor Fault
E15
Dryer displays E15; on condenser or heat pump models, the compressor or heat pump may not run.
Heat Pump / Compressor System Fault (heat pump models only)
E16
Dryer shows E16; may not respond to button presses or may behave erratically.
Keypad / Button Stuck or Shorted
E17
Dryer displays E17; door may not lock or unlock correctly at the start or end of the cycle.
Door Locking Mechanism Error
E18
Dryer shows E18; may stop mid-cycle with a beeping alarm; often related to water tank on condenser models.
Water Tank Full / Level Sensor Fault
E19
Dryer displays E19; may not heat correctly or may shut down unexpectedly.
Internal Communication Error (PCB-to-Module)
E20
Dryer shows E20; may not start or may stop with no other obvious symptoms.
General System Error / Undefined Fault
Symptom
Dryer display and lights work, but there is no response from any buttons or the knob.
User Interface Lockup / Control Panel Failure
Symptom
Dryer display shows incorrect remaining time or jumps suddenly to end of cycle while clothes are still wet.
Sensor Drying Calibration / Moisture Detection Issue
Symptom
Dryer door pops open during the cycle, causing the machine to stop.
Door Latch / Strike Failure
Symptom
Dryer door will not open at the end of the cycle; door appears locked even though the machine is off.
Door Lock Stuck Closed
Symptom
Dryer drum does not turn and there is only a humming noise when Start is pressed.
Seized Motor or Start Capacitor Failure
Symptom
Dryer drum does not turn, but the motor can be heard running or humming.
Drum Drive Failure
Symptom
Dryer emits a burning smell during operation, with or without visible smoke.
Overheating / Lint Ignition Risk
Symptom
Dryer emits a musty or moldy odor when running, especially at the start of the cycle.
Odor / Bacterial Growth in Lint and Condensate Areas
Symptom
Dryer interior light does not turn on when the door is opened, but the dryer otherwise works.
Drum Light Circuit Failure
Symptom
Dryer leaks water onto the floor, especially on condenser or heat pump models.
Water Leakage / Condensate Management Fault
Symptom
Dryer makes loud squealing or screeching noises during operation.
Worn Drum Support Components
Symptom
Dryer powers on but will not start the cycle when Start/Pause is pressed; display remains on the program screen.
Start Circuit / Safety Interlock Fault
Symptom
Dryer produces a loud banging or thumping noise as the drum turns.
Drum Imbalance or Support Wear
Symptom
Dryer produces a rattling or metallic clinking noise during operation.
Foreign Object in Drum or Blower
Symptom
Dryer runs but clothes come out very wrinkled and excessively hot.
Overheating / Incorrect Temperature Control
Symptom
Dryer runs but does not heat; clothes remain cold and wet at the end of the cycle.
No Heat Condition
Symptom
Dryer stops mid-cycle and will not resume unless power is cycled.
Intermittent Power or Overheat Shutdown
Symptom
Dryer takes too long to dry clothes; loads are still damp after a full cycle.
Poor Drying Performance / Extended Dry Times
Symptom
Dryer trips the household circuit breaker or RCD during or shortly after starting.
Electrical Short or Ground Fault
Symptom
Dryer vibrates excessively or moves across the floor during operation.
Excessive Vibration / Unstable Installation
Symptom
Dryer will not start at all; no lights or display when the power button is pressed.
No Power / Dead Appliance
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E01 |
Dryer will not start; display shows E01 immediately after pressing the start button.
|
Door Lock / Door Switch Fault | View Details |
| E02 |
Dryer stops shortly after starting and displays E02; drum may tumble briefly then shut off.
|
Overheating / High Temperature Cut-Out | View Details |
| E03 |
Dryer displays E03 and stops; clothes remain damp; often occurs early in the cycle.
|
NTC Temperature Sensor Fault | View Details |
| E04 |
Dryer shows E04 and will not start or stops mid-cycle; may be accompanied by no heat.
|
Heating Circuit Failure | View Details |
| E05 |
Dryer displays E05 and does not start; sometimes accompanied by a humming noise from the motor area.
|
Motor Start Failure / Motor Circuit Fault | View Details |
| E06 |
Dryer shows E06 and stops; may not heat properly or may overheat; cycle times become erratic.
|
Moisture Sensor / Humidity Detection Fault | View Details |
| E07 |
Dryer displays E07 and stops; on condenser models, water may not collect in the tank or may leak.
|
Condenser Pump / Drainage Fault | View Details |
| E08 |
Dryer shows E08; drum may not rotate even though the motor can be heard or attempts to start.
|
Drive Belt / Drum Rotation Fault | View Details |
| E09 |
Dryer displays E09 and will not start; sometimes occurs after a power surge or outage.
|
Control Board / EEPROM Error | View Details |
| E10 |
Dryer shows E10 and does not start; often associated with incorrect or unstable mains voltage.
|
Power Supply / Voltage Detection Fault | View Details |
| E11 |
Dryer displays E11; on condenser models, drying performance is poor and the unit may stop prematurely.
|
Condenser Airflow / Heat Exchanger Blockage | View Details |
| E12 |
Dryer shows E12; cycle may not start or may stop; often related to sensor drying programs.
|
Program Selector / User Interface Communication Fault | View Details |
| E13 |
Dryer displays E13; may be accompanied by unusual noises or failure to rotate.
|
Tachometer / Motor Speed Feedback Fault | View Details |
| E14 |
Dryer shows E14 and stops; may be associated with overheating or very long drying times.
|
Exhaust Air Temperature / Outlet Sensor Fault | View Details |
| E15 |
Dryer displays E15; on condenser or heat pump models, the compressor or heat pump may not run.
|
Heat Pump / Compressor System Fault (heat pump models only) | View Details |
| E16 |
Dryer shows E16; may not respond to button presses or may behave erratically.
|
Keypad / Button Stuck or Shorted | View Details |
| E17 |
Dryer displays E17; door may not lock or unlock correctly at the start or end of the cycle.
|
Door Locking Mechanism Error | View Details |
| E18 |
Dryer shows E18; may stop mid-cycle with a beeping alarm; often related to water tank on condenser models.
|
Water Tank Full / Level Sensor Fault | View Details |
| E19 |
Dryer displays E19; may not heat correctly or may shut down unexpectedly.
|
Internal Communication Error (PCB-to-Module) | View Details |
| E20 |
Dryer shows E20; may not start or may stop with no other obvious symptoms.
|
General System Error / Undefined Fault | View Details |
| – |
Dryer display and lights work, but there is no response from any buttons or the knob.
|
User Interface Lockup / Control Panel Failure | View Details |
| – |
Dryer display shows incorrect remaining time or jumps suddenly to end of cycle while clothes are still wet.
|
Sensor Drying Calibration / Moisture Detection Issue | View Details |
| – |
Dryer door pops open during the cycle, causing the machine to stop.
|
Door Latch / Strike Failure | View Details |
| – |
Dryer door will not open at the end of the cycle; door appears locked even though the machine is off.
|
Door Lock Stuck Closed | View Details |
| – |
Dryer drum does not turn and there is only a humming noise when Start is pressed.
|
Seized Motor or Start Capacitor Failure | View Details |
| – |
Dryer drum does not turn, but the motor can be heard running or humming.
|
Drum Drive Failure | View Details |
| – |
Dryer emits a burning smell during operation, with or without visible smoke.
|
Overheating / Lint Ignition Risk | View Details |
| – |
Dryer emits a musty or moldy odor when running, especially at the start of the cycle.
|
Odor / Bacterial Growth in Lint and Condensate Areas | View Details |
| – |
Dryer interior light does not turn on when the door is opened, but the dryer otherwise works.
|
Drum Light Circuit Failure | View Details |
| – |
Dryer leaks water onto the floor, especially on condenser or heat pump models.
|
Water Leakage / Condensate Management Fault | View Details |
| – |
Dryer makes loud squealing or screeching noises during operation.
|
Worn Drum Support Components | View Details |
| – |
Dryer powers on but will not start the cycle when Start/Pause is pressed; display remains on the program screen.
|
Start Circuit / Safety Interlock Fault | View Details |
| – |
Dryer produces a loud banging or thumping noise as the drum turns.
|
Drum Imbalance or Support Wear | View Details |
| – |
Dryer produces a rattling or metallic clinking noise during operation.
|
Foreign Object in Drum or Blower | View Details |
| – |
Dryer runs but clothes come out very wrinkled and excessively hot.
|
Overheating / Incorrect Temperature Control | View Details |
| – |
Dryer runs but does not heat; clothes remain cold and wet at the end of the cycle.
|
No Heat Condition | View Details |
| – |
Dryer stops mid-cycle and will not resume unless power is cycled.
|
Intermittent Power or Overheat Shutdown | View Details |
| – |
Dryer takes too long to dry clothes; loads are still damp after a full cycle.
|
Poor Drying Performance / Extended Dry Times | View Details |
| – |
Dryer trips the household circuit breaker or RCD during or shortly after starting.
|
Electrical Short or Ground Fault | View Details |
| – |
Dryer vibrates excessively or moves across the floor during operation.
|
Excessive Vibration / Unstable Installation | View Details |
| – |
Dryer will not start at all; no lights or display when the power button is pressed.
|
No Power / Dead Appliance | View Details |
No matching codes found
Advertisements