Hotpoint-Ariston
Hotpoint-Ariston Ranges & Cooktops Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
F01
Electric oven will not heat, display shows F01 shortly after a cooking program is selected.
Main Power Relay / Electronic Control Board Failure
F02
Electric oven does not reach set temperature, display shows F02 during preheat.
Oven Temperature Sensor (NTC) Fault
F03
Oven fan does not run, oven overheats or shuts down with F03 on the display.
Cooling / Convection Fan Motor Failure
F04
Oven display shows F04 and the oven will not start or stops mid-cycle.
Oven Door Lock / Latch Circuit Fault
F05
Oven display shows F05 and the oven light and fan may work but heating does not start.
Oven Overheat Thermostat / Safety Cut-Out Tripped or Faulty
F06
Oven display shows F06 and controls may be unresponsive or behave erratically.
User Interface / Touch Control Panel Communication Error
F07
Oven shows F07 and will not heat; sometimes accompanied by tripping of the household breaker.
Heating Element Short Circuit to Ground
F08
Oven display shows F08 and the oven may overheat or not regulate temperature correctly.
Relay Stuck or Heating Control Circuit Fault
F09
Oven display shows F09 and the clock/programmer cannot be set or loses settings.
EEPROM / Memory Error in Control Module
F10
Oven display shows F10 and the oven does not heat or heats erratically.
Temperature Calibration / Sensor Range Error
F11
Gas oven ignition fails and the display shows F11 after several clicking attempts.
Gas Oven Ignition Failure
F12
Gas cooktop burners will not ignite and the range display shows F12.
Cooktop Ignition System Failure
F13
Induction cooktop zone does not heat and the display shows F13 for that zone.
Induction Coil or Power Module Fault
F14
Induction cooktop shows F14 and all zones are disabled.
Cooktop Cooling System / Overtemperature Fault
F15
Induction cooktop zone shows F15 when a pan is placed on it and does not heat.
Pan Detection Error
F16
Induction cooktop shows F16 and beeps continuously when attempting to use any zone.
Touch Control Panel Fault
F17
Induction cooktop shows F17 and zones shut down shortly after starting.
Supply Voltage Out of Range
F18
Induction cooktop shows F18 and one or more zones cannot be activated.
Zone Configuration / Communication Error
F19
Induction cooktop shows F19 and shuts down when higher power levels are selected.
Overcurrent / Power Limitation Fault
F20
Gas cooktop shows F20 or a flashing gas symbol and shuts off gas shortly after ignition.
Flame Supervision Device (FSD) / Thermocouple Fault
Symptom
Clock/programmer display is blank and oven functions cannot be set, but cooktop still works.
Oven Programmer / Display Power Failure
Symptom
Control panel buttons or touch keys do not respond, but the display is lit.
User Interface Input Failure
Symptom
Cooktop control knobs are hard to turn or feel loose and wobbly.
Worn Gas Valve Spindles or Damaged Knobs
Symptom
Cooktop glass-ceramic surface is cracked or shattered.
Damaged Glass-Ceramic Top
Symptom
Electric oven does not heat on bake function, but grill/broil may still work.
Lower (Bake) Heating Element Failure
Symptom
Electric oven does not heat on grill/broil function, but bake may still work.
Upper (Grill/Broil) Heating Element Failure
Symptom
Gas cooktop burner clicks and sparks but the flame does not light or lights and then goes out when the knob is released.
Gas Flow or Flame Supervision Problem
Symptom
Gas cooktop burner flame is yellow, noisy, or lifts off the burner head.
Incorrect Combustion / Air–Gas Mixture Issue
Symptom
Gas cooktop burner will not ignite, no clicking sound is heard when the knob is turned to the ignition position.
Ignition Switch or Power Supply Failure
Symptom
Gas cooktop igniters keep clicking continuously even when all burner knobs are in the OFF position.
Stuck Ignition Switch or Moisture in Ignition System
Symptom
Oven door glass is loose, rattling, or has condensation between the panes.
Door Glass Assembly / Seal Failure
Symptom
Oven door will not close fully or appears misaligned, causing heat to escape.
Door Hinge or Hinge Receiver Failure
Symptom
Oven door will not unlock after a self-clean or pyrolytic cycle has finished.
Door Lock Mechanism Stuck Closed
Symptom
Oven fan makes loud rattling, scraping, or humming noises during operation.
Worn or Obstructed Convection / Cooling Fan
Symptom
Oven fan runs continuously even when the oven is off and cool.
Cooling Fan Control Stuck On
Symptom
Oven interior light and fan turn on when the door is opened, but the oven does not start cooking when a program is selected.
Programmer Not Enabling Heating
Symptom
Oven interior light does not work, but the oven heats normally.
Oven Lamp Circuit Failure
Symptom
Oven light, fan, and display work, but no heating on any function.
Main Power Supply to Heating Circuit Interrupted
Symptom
Oven produces excessive smoke or burning smell during normal cooking.
Contamination or Incorrect Use Causing Overheating of Residues
Symptom
Oven temperature is consistently too high or too low compared to the set temperature.
Oven Temperature Calibration / Sensor Drift
Symptom
Radiant (non-induction) electric cooktop zone does not heat or only heats partially.
Radiant Heating Element or Limiter Failure
Symptom
Range trips the household circuit breaker or RCD when the oven or a cooktop zone is turned on.
Earth Leakage or Short Circuit
Symptom
Strong gas smell around the range or cooktop, especially when not in use.
Gas Leak in Supply or Burner Circuit
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| F01 |
Electric oven will not heat, display shows F01 shortly after a cooking program is selected.
|
Main Power Relay / Electronic Control Board Failure | View Details |
| F02 |
Electric oven does not reach set temperature, display shows F02 during preheat.
|
Oven Temperature Sensor (NTC) Fault | View Details |
| F03 |
Oven fan does not run, oven overheats or shuts down with F03 on the display.
|
Cooling / Convection Fan Motor Failure | View Details |
| F04 |
Oven display shows F04 and the oven will not start or stops mid-cycle.
|
Oven Door Lock / Latch Circuit Fault | View Details |
| F05 |
Oven display shows F05 and the oven light and fan may work but heating does not start.
|
Oven Overheat Thermostat / Safety Cut-Out Tripped or Faulty | View Details |
| F06 |
Oven display shows F06 and controls may be unresponsive or behave erratically.
|
User Interface / Touch Control Panel Communication Error | View Details |
| F07 |
Oven shows F07 and will not heat; sometimes accompanied by tripping of the household breaker.
|
Heating Element Short Circuit to Ground | View Details |
| F08 |
Oven display shows F08 and the oven may overheat or not regulate temperature correctly.
|
Relay Stuck or Heating Control Circuit Fault | View Details |
| F09 |
Oven display shows F09 and the clock/programmer cannot be set or loses settings.
|
EEPROM / Memory Error in Control Module | View Details |
| F10 |
Oven display shows F10 and the oven does not heat or heats erratically.
|
Temperature Calibration / Sensor Range Error | View Details |
| F11 |
Gas oven ignition fails and the display shows F11 after several clicking attempts.
|
Gas Oven Ignition Failure | View Details |
| F12 |
Gas cooktop burners will not ignite and the range display shows F12.
|
Cooktop Ignition System Failure | View Details |
| F13 |
Induction cooktop zone does not heat and the display shows F13 for that zone.
|
Induction Coil or Power Module Fault | View Details |
| F14 |
Induction cooktop shows F14 and all zones are disabled.
|
Cooktop Cooling System / Overtemperature Fault | View Details |
| F15 |
Induction cooktop zone shows F15 when a pan is placed on it and does not heat.
|
Pan Detection Error | View Details |
| F16 |
Induction cooktop shows F16 and beeps continuously when attempting to use any zone.
|
Touch Control Panel Fault | View Details |
| F17 |
Induction cooktop shows F17 and zones shut down shortly after starting.
|
Supply Voltage Out of Range | View Details |
| F18 |
Induction cooktop shows F18 and one or more zones cannot be activated.
|
Zone Configuration / Communication Error | View Details |
| F19 |
Induction cooktop shows F19 and shuts down when higher power levels are selected.
|
Overcurrent / Power Limitation Fault | View Details |
| F20 |
Gas cooktop shows F20 or a flashing gas symbol and shuts off gas shortly after ignition.
|
Flame Supervision Device (FSD) / Thermocouple Fault | View Details |
| – |
Clock/programmer display is blank and oven functions cannot be set, but cooktop still works.
|
Oven Programmer / Display Power Failure | View Details |
| – |
Control panel buttons or touch keys do not respond, but the display is lit.
|
User Interface Input Failure | View Details |
| – |
Cooktop control knobs are hard to turn or feel loose and wobbly.
|
Worn Gas Valve Spindles or Damaged Knobs | View Details |
| – |
Cooktop glass-ceramic surface is cracked or shattered.
|
Damaged Glass-Ceramic Top | View Details |
| – |
Electric oven does not heat on bake function, but grill/broil may still work.
|
Lower (Bake) Heating Element Failure | View Details |
| – |
Electric oven does not heat on grill/broil function, but bake may still work.
|
Upper (Grill/Broil) Heating Element Failure | View Details |
| – |
Gas cooktop burner clicks and sparks but the flame does not light or lights and then goes out when the knob is released.
|
Gas Flow or Flame Supervision Problem | View Details |
| – |
Gas cooktop burner flame is yellow, noisy, or lifts off the burner head.
|
Incorrect Combustion / Air–Gas Mixture Issue | View Details |
| – |
Gas cooktop burner will not ignite, no clicking sound is heard when the knob is turned to the ignition position.
|
Ignition Switch or Power Supply Failure | View Details |
| – |
Gas cooktop igniters keep clicking continuously even when all burner knobs are in the OFF position.
|
Stuck Ignition Switch or Moisture in Ignition System | View Details |
| – |
Oven door glass is loose, rattling, or has condensation between the panes.
|
Door Glass Assembly / Seal Failure | View Details |
| – |
Oven door will not close fully or appears misaligned, causing heat to escape.
|
Door Hinge or Hinge Receiver Failure | View Details |
| – |
Oven door will not unlock after a self-clean or pyrolytic cycle has finished.
|
Door Lock Mechanism Stuck Closed | View Details |
| – |
Oven fan makes loud rattling, scraping, or humming noises during operation.
|
Worn or Obstructed Convection / Cooling Fan | View Details |
| – |
Oven fan runs continuously even when the oven is off and cool.
|
Cooling Fan Control Stuck On | View Details |
| – |
Oven interior light and fan turn on when the door is opened, but the oven does not start cooking when a program is selected.
|
Programmer Not Enabling Heating | View Details |
| – |
Oven interior light does not work, but the oven heats normally.
|
Oven Lamp Circuit Failure | View Details |
| – |
Oven light, fan, and display work, but no heating on any function.
|
Main Power Supply to Heating Circuit Interrupted | View Details |
| – |
Oven produces excessive smoke or burning smell during normal cooking.
|
Contamination or Incorrect Use Causing Overheating of Residues | View Details |
| – |
Oven temperature is consistently too high or too low compared to the set temperature.
|
Oven Temperature Calibration / Sensor Drift | View Details |
| – |
Radiant (non-induction) electric cooktop zone does not heat or only heats partially.
|
Radiant Heating Element or Limiter Failure | View Details |
| – |
Range trips the household circuit breaker or RCD when the oven or a cooktop zone is turned on.
|
Earth Leakage or Short Circuit | View Details |
| – |
Strong gas smell around the range or cooktop, especially when not in use.
|
Gas Leak in Supply or Burner Circuit | View Details |
No matching codes found
Advertisements