IPSO
IPSO Washing Machines Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E01
Washer will not start; display shows E01 immediately after pressing Start
Door Lock Failure
E02
Washer does not fill with water or fills very slowly; E02 displayed after a few minutes
Water Inlet Fill Timeout
E03
Washer does not drain; water remains in drum and E03 is displayed
Drain Timeout / Drain Pump Failure
E04
Washer overfills or water level too high; E04 displayed and cycle stops
Overfill / Water Level Sensor Fault
E05
Washer does not heat water; cycle may extend indefinitely and E05 is displayed
Heating Circuit Failure
E06
Washer drum does not rotate; E06 displayed shortly after cycle start
Motor Drive Fault
E07
Washer will not spin; E07 displayed near the spin phase
Unbalanced Load / Spin Protection Fault
E08
Washer stops mid-cycle with E08; drum may be locked or difficult to turn
Motor Overload / Drum Jam
E09
Washer stops and displays E09; no obvious mechanical issue, may occur randomly
EEPROM / Control Board Configuration Error
E10
Washer door remains locked at end of cycle; E10 displayed
Door Unlock Failure
E11
Washer fills but then stops with E11; water level appears incorrect for selected program
Water Level Calibration / Pressure Sensor Range Error
E12
Washer stops and displays E12; often associated with very hot water or steam
Temperature Sensor (NTC) Fault
E13
Washer shows E13 and may stop during drain or spin; sometimes accompanied by water leak detection
Leak / Overflow Protection Activated
E14
Washer displays E14; cycle may not start or may stop unexpectedly
Door Open Detection Error
E15
Washer shows E15; user interface may be unresponsive or buttons not working correctly
User Interface / Keypad Communication Error
E16
Washer displays E16; often associated with excessive vibration or spin abort
Tachometer / Speed Sensor Error
E17
Washer shows E17; water temperature too high for selected program or safety cut-out triggered
Overtemperature Protection
E18
Washer displays E18; water level does not drop as expected during spin
Drain Level Sensor / Siphon Error
E19
Washer shows E19; often related to coin or card payment system on commercial IPSO units
Payment System Communication Error
E20
Washer displays E20; motor runs erratically or not at all on inverter-driven IPSO models
Inverter / Frequency Drive Fault
Symptom
Washer display works but some buttons do not respond or respond intermittently
Keypad / Button Failure
Symptom
Washer does not dispense detergent or softener properly
Dispenser Drawer / Valve Flow Issue
Symptom
Washer does not start; display is on but Start button does nothing
Start Circuit / Door Interlock Logic Fault
Symptom
Washer does not start; no lights or display
No Power / Dead Machine
Symptom
Washer door seal is torn or moldy but no active leak yet
Door Gasket Deterioration
Symptom
Washer door will not unlock at end of cycle; no error code shown
Mechanical Door Lock Jam
Symptom
Washer drum overfills and water can be seen near the door glass but no code is shown
Water Level Control Malfunction
Symptom
Washer drum scrapes or grinds when turning by hand
Foreign Object Between Drum and Tub
Symptom
Washer emits a burning smell during operation
Overheating Component or Friction
Symptom
Washer fills and drains but drum does not turn at all
Drive System Failure
Symptom
Washer has a strong musty or moldy odor inside drum
Biofilm and Mold Build-Up
Symptom
Washer leaks water from front during wash or rinse
Door Gasket (Boot Seal) Leak
Symptom
Washer leaks water from underneath the cabinet during operation
Internal Hose or Pump Leak
Symptom
Washer leaves clothes soaking wet at end of cycle
No or Poor Final Spin
Symptom
Washer makes loud banging or knocking noise during spin
Suspension or Shock Absorber Wear
Symptom
Washer makes loud rumbling or roaring noise during spin
Drum Bearing Failure
Symptom
Washer takes much longer than expected to complete cycles
Extended Cycle Time / Control Compensation
Symptom
Washer trips the circuit breaker or blows fuses during operation
Electrical Short or Ground Fault
Symptom
Washer vibrates excessively and walks across the floor during spin
Excessive Vibration / Out-of-Balance Condition
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E01 |
Washer will not start; display shows E01 immediately after pressing Start
|
Door Lock Failure | View Details |
| E02 |
Washer does not fill with water or fills very slowly; E02 displayed after a few minutes
|
Water Inlet Fill Timeout | View Details |
| E03 |
Washer does not drain; water remains in drum and E03 is displayed
|
Drain Timeout / Drain Pump Failure | View Details |
| E04 |
Washer overfills or water level too high; E04 displayed and cycle stops
|
Overfill / Water Level Sensor Fault | View Details |
| E05 |
Washer does not heat water; cycle may extend indefinitely and E05 is displayed
|
Heating Circuit Failure | View Details |
| E06 |
Washer drum does not rotate; E06 displayed shortly after cycle start
|
Motor Drive Fault | View Details |
| E07 |
Washer will not spin; E07 displayed near the spin phase
|
Unbalanced Load / Spin Protection Fault | View Details |
| E08 |
Washer stops mid-cycle with E08; drum may be locked or difficult to turn
|
Motor Overload / Drum Jam | View Details |
| E09 |
Washer stops and displays E09; no obvious mechanical issue, may occur randomly
|
EEPROM / Control Board Configuration Error | View Details |
| E10 |
Washer door remains locked at end of cycle; E10 displayed
|
Door Unlock Failure | View Details |
| E11 |
Washer fills but then stops with E11; water level appears incorrect for selected program
|
Water Level Calibration / Pressure Sensor Range Error | View Details |
| E12 |
Washer stops and displays E12; often associated with very hot water or steam
|
Temperature Sensor (NTC) Fault | View Details |
| E13 |
Washer shows E13 and may stop during drain or spin; sometimes accompanied by water leak detection
|
Leak / Overflow Protection Activated | View Details |
| E14 |
Washer displays E14; cycle may not start or may stop unexpectedly
|
Door Open Detection Error | View Details |
| E15 |
Washer shows E15; user interface may be unresponsive or buttons not working correctly
|
User Interface / Keypad Communication Error | View Details |
| E16 |
Washer displays E16; often associated with excessive vibration or spin abort
|
Tachometer / Speed Sensor Error | View Details |
| E17 |
Washer shows E17; water temperature too high for selected program or safety cut-out triggered
|
Overtemperature Protection | View Details |
| E18 |
Washer displays E18; water level does not drop as expected during spin
|
Drain Level Sensor / Siphon Error | View Details |
| E19 |
Washer shows E19; often related to coin or card payment system on commercial IPSO units
|
Payment System Communication Error | View Details |
| E20 |
Washer displays E20; motor runs erratically or not at all on inverter-driven IPSO models
|
Inverter / Frequency Drive Fault | View Details |
| – |
Washer display works but some buttons do not respond or respond intermittently
|
Keypad / Button Failure | View Details |
| – |
Washer does not dispense detergent or softener properly
|
Dispenser Drawer / Valve Flow Issue | View Details |
| – |
Washer does not start; display is on but Start button does nothing
|
Start Circuit / Door Interlock Logic Fault | View Details |
| – |
Washer does not start; no lights or display
|
No Power / Dead Machine | View Details |
| – |
Washer door seal is torn or moldy but no active leak yet
|
Door Gasket Deterioration | View Details |
| – |
Washer door will not unlock at end of cycle; no error code shown
|
Mechanical Door Lock Jam | View Details |
| – |
Washer drum overfills and water can be seen near the door glass but no code is shown
|
Water Level Control Malfunction | View Details |
| – |
Washer drum scrapes or grinds when turning by hand
|
Foreign Object Between Drum and Tub | View Details |
| – |
Washer emits a burning smell during operation
|
Overheating Component or Friction | View Details |
| – |
Washer fills and drains but drum does not turn at all
|
Drive System Failure | View Details |
| – |
Washer has a strong musty or moldy odor inside drum
|
Biofilm and Mold Build-Up | View Details |
| – |
Washer leaks water from front during wash or rinse
|
Door Gasket (Boot Seal) Leak | View Details |
| – |
Washer leaks water from underneath the cabinet during operation
|
Internal Hose or Pump Leak | View Details |
| – |
Washer leaves clothes soaking wet at end of cycle
|
No or Poor Final Spin | View Details |
| – |
Washer makes loud banging or knocking noise during spin
|
Suspension or Shock Absorber Wear | View Details |
| – |
Washer makes loud rumbling or roaring noise during spin
|
Drum Bearing Failure | View Details |
| – |
Washer takes much longer than expected to complete cycles
|
Extended Cycle Time / Control Compensation | View Details |
| – |
Washer trips the circuit breaker or blows fuses during operation
|
Electrical Short or Ground Fault | View Details |
| – |
Washer vibrates excessively and walks across the floor during spin
|
Excessive Vibration / Out-of-Balance Condition | View Details |
No matching codes found
Advertisements